2010 Alfa Romeo Giulietta boot

128
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
fig. 89A0K0115mfig. 90A0K0222m
FUEL FILLER CAP
The fuel cap is unlocked when the central locking system is released
and automatically locked when the central locking system is ap-
plied.
To open
Press the flap A-fig. 89 to release it and reach the fuel filler cap
B. Then press the cap B and turn it anticlockwise.
The cap has a loss prevention device C which secures it to the flap
so that it cannot be lost. Attach the cap to device D during refu-
elling.
How to open the flap in an emergency
In case of emergency, pull the cord A-fig. 90 on the right-hand side
of the boot to open the fuel flap.
Closing
Release the cap B from the device D and insert it in its housing.
Tighten the cap in a clockwise direction until one or more clicks are
heard. Finally, close the flap A and check that is it correctly locked.
The hermetic seal may cause a slight increase in pressure in the
tank. A suction noise when you release the cap is therefore entirely
normal.
Do not place naked flames or lit cigarettes near
to the fuel filler: fire risk. Keep your face away
from the fuel tank opening to avoid breathing in
harmful vapours.
001-130 Alfa Giulietta EN 5ed 26-07-2010 16:34 Pagina 128

155
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
SAVING FUEL
Here are some suggestions which may help you to save fuel and
lower the amount of harmful emissions released into the atmos-
phere.
GENERAL CONSIDERATIONS
Car maintenance
Have checks and adjustments carried out in accordance with the
“Scheduled Servicing Plan” (see chapter “Servicing and mainte-
nance”).
Tyres
Check the tyre pressure at least once every 4 weeks: if the pres-
sure is too low, consumption levels increase as resistance to rolling
is higher.
Unnecessar y loads
Do not travel with an overloaded boot. The weight of the car and
its arrangement greatly affect fuel consumption and stability.
Roof rack/ski rack
Remove the roof rack or the ski rack from the roof after use. These
accessories decrease aerodynamic penetration and have a nega-
tive effect on fuel consumption. It is better to use a trailer to trans-
port particularly bulky objects.
Electric devices
Use electric devices only for the amount of time needed. The heat-
ed rear windscreen, additional headlights, windscreen wipers and
heater fan require a considerable amount of energy; increasing the
current uptake increases fuel consumption (by up to +25% in an
urban cycle).
Climate control system
Using the climate control system will increase consumption: use
the air vents when the external temperature so allows.
Spoilers
The use of non-certified spoilers may adversely affect aerodynam-
ics and fuel consumption.
151-160 Alfa Giulietta EN 3ed 13-04-2010 11:46 Pagina 155

164
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Replace the wheel as follows:
❍stop the car in a position so that it is not a danger for on-com-
ing traffic and where you can replace the wheel safely. The
ground must be flat and solid;
❍switch off the engine, pull up the handbrake and engage 1st
gear or reverse; put on the high visibility jacket (required by
law) before leaving the car;
❍open the boot, pull tab A-fig. 113 and lift up the mat;
❍using the wrench A - fig. 114 positioned in the tool box, loosen
the locking device, take the tool box B and place it close to the
wheel to be replaced, then take the space/saver wheel C;
fig. 115A0K0038m
❍take tool A-fig. 115 and loosen the fastening bolts by ap-
proximately one turn. For versions with alloy rims, shake the
car to facilitate detachment of the rim from the wheel hub.
fig. 114A0K0124m
fig. 113A0K0168m
161-198 Alfa Giulietta EN 4ed 5-05-2010 9:04 Pagina 164

166
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
fig. 118A0K0040mfig. 119A0K0235m
❍use the wrench A-fig. 115 provided to fasten the bolts com-
pletely in a criss-cross fashion as per the order illustrated in
fig. 118;
❍when replacing an alloy wheel it is advisable to place it upside
down, with the aesthetic part facing upwards.
Restore the standard wheel as soon as possible, because, once placed
in the associated compartment, the luggage compartment load plat-
form is rendered uneven as the standard wheel is larger than the
spare wheel.
REMOVING THE SUBWOOFER
(versions with Bose HI-FI)
(for versions/markets, where provided)
IMPORTANT The following procedure only applies to cars equipped
with Bose HI-FI systems with subwoofer (for versions/markets,
where provided).
Subwoofer and space-saver spare wheel
On these versions, the tools needed for changing the wheel are
arranged in a specific container on the left-hand side of the boot
(see fig. 119). The jack is located in a pocket, again on the left-
hand side of the boot (see fig. 119a).
161-198 Alfa Giulietta EN 4ed 5-05-2010 9:04 Pagina 166

167
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
When you have finished:
❍reposition the subwoofer correctly (see indications on the label
applied over the subwoofer itself), so that the word “BOSE”
is positioned in the right direction for reading;
❍reposition the subwoofer wire correctly to avoid pinching it. Then
fasten the clip B-fig. 120 and fasten the blocking device.Finally,
position the load compartment spacer fig. 119 correctly and
lower the boot mat.
fig. 120A0K0236mfig. 119aA0K0228m
Proceed as follows to remove the subwoofer:
❍open the boot, pull the tab A-fig. 113, lift the mat upwards and
remove the load compartment spacer fig. 119;
❍loosen the fastening device A-fig. 120, remove the clip B fas-
tening the cable and then lift the subwoofer;
❍rest the subwoofer on the side of the boot and take the space-
saver spare wheel;
❍then replace the wheel as described above.
161-198 Alfa Giulietta EN 4ed 5-05-2010 9:04 Pagina 167

168
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
REFITTING THE WHEEL
Following the procedure previously described, raise the car and
remove the space-saver spare wheel.
Proceed as follows:
❍make sure the contact surfaces between standard wheel and
hub are clean so that the fastening bolts will not come loose;
❍for versions with steel rims: fixed the wheel hub onto the rim;
❍fit the hub cap by aligning the crescent hole with the bolt you
have fitted, then insert the other 4 bolts;
❍tighten the retaining bolts using wrench A-fig. 115;
❍lower the car and remove the jack;
❍use wrench A-fig. 115 to fully tighten the bolts, following the
sequence shown in fig. 118;
When you have finished:
❍stow the space-saver spare wheel in the compartment provid-
ed in the boot;
❍insert the jack and the other tools in the container;
❍arrange the container and tools on the space-saver spare wheel;
❍reposition the boot mat correctly.
Subwoofer and “Automatic Fix&Go Kit”
Locating the Automatic Fix&Go Kit:
❍open the boot, pull tab A-fig. 113 and lift up the mat;
❍take the “Automatic Fix&Go Kit” located on the left side of the
boot (fig. 121);
❍inflate the wheel (see “Automatic Fix&Go Kit”).
IMPORTANT If you need to remove the subwoofer follow the indi-
cations shown on the adhesive label fig. 121 over the subwoofer
itself to reposition it correctly.
fig. 121A0K0178m
161-198 Alfa Giulietta EN 4ed 5-05-2010 9:04 Pagina 168

169
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
“Automatic Fix&Go” KIT
This is located in the boot (the kit container may change according
to versions - see fig. 122). The kit container also contains a screw-
driver and the tow ring. The kit contains:
❍a bottle A-fig. 122a containing sealing liquid, provided with:
filling tube B and adhesive label C with the wording
“max. 80 km/h” to be placed in a clearly visible position
(e.g. on the dashboard) after repairing the tyre;
fig. 122aA0K0019m
fig. 122A0K0126mfig. 123A0K0020m
❍a compressor D complete with pressure gauge and connectors;
❍an information booklet fig. 123, providing instructions for us-
ing the kit correctly. This booklet should be given to the per-
sons charged with handling the tyre treated with this kit;
161-198 Alfa Giulietta EN 4ed 5-05-2010 9:04 Pagina 169

–
–
55W
55W
D1S
24W
10W
–
–
–
5W
55W
21W
21W
10W
5W
5W
5WLED
LED
H7
H1
F
PY24W
R10W
LED
LED
LED
W5W
H3
H21W
P21W
C10W
W5W
C5W
W5W
176
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
–
–
D
E
–
B
B
–
–
–
A
E
B
B
C
A
C
A
Bulbs Type Power Ref. figure 130
Front side lights/Day lights (DRL)
Rear side lights
Dipped beams
Main beams
Main/Dipped beams
(versions with Bi-Xenon headlights)
(for versions/markets, where provided)
Front direction indicators
Rear direction indicators
Side direction indicators
Brake light
3rd brake light
Number plate light
Fog lights
Rear fog light
Reverse light
Front ceiling light
Boot courtesy light
Glove compartment courtesy light
Puddle light
161-198 Alfa Giulietta EN 4ed 5-05-2010 9:04 Pagina 176