2010 Acura TSX Trans

µµ When you unlock the driver’s door
with your remote transmitter, each
remote transmitter activates the
customized settings related to that
remote.
Press and hold this
button for about 1 second to attract
attention; the horn will sound, and
the exterior lights will f lash f or about
30 seconds. To cancel panic mode,
press any other button on the remote
transmitter, or turn the ignition
switch to the ON (II) position. Panic
mode does not work when the key is
in the ignition switch.
Press and hold this
button f or about 1 second to open
the trunk. You cannot open the trunk
if the key is in the ignition switch.
The driving position memory
activated (Driver 1, Driver 2) is
shownonthebackof each
transmitter. Make sure you store
your desired driving position in thememory that is activated by the
transmitter you normally carry.
Here are the settings activated with
the remote:
Customized settings
(see page ).
Driving position memory
(see page ).
When you unlock and open the
driver’s door with the remote
transmitter, the driver’s seat moves
to the position stored in memory.
You will hear two beeps when the
movement is completed. The
indicator in the related memory
button on the driver’s door remains
on. 81
142
CONT INUED
All models except Canadian TSX with 4-cylinder engine
Recalling a Memorized Driving
Position
PA NIC
TRUNK
Remote Transmitter
Inst rument s and Cont rols
127
With Driver 2
With Driver 1
2010 TSX

Avoid dropping or throwing the
transmitter.
Protect the transmitter from
extreme temperature.
Do not immerse the transmitter in
any liquid.
If you lose a transmitter, the
replacement needs to be
reprogrammed by your dealer.
If it takes several pushes on the
button to lock or unlock the doors,
replace the battery as soon as
possible.
Battery type: CR1616 Separate the keypad from the
transmitter by pushing any button
f rom outside.Be caref ul when removing
this screw as the head of the screw
can strip out. Remove the screw at the base of
the transmitter with a small
Phillips-head screwdriver.
To replace the battery:
To turn the memory position link
settings back on, repeat this
procedure. The LED will blink once
to indicate the feature has been
turned on. You can turn of f this driving position
memory activation. Press and hold
the LOCK and UNLOCK buttons at
thesametime.TheLEDinthe
remote transmitter will blink twice.
Then release the buttons. Doing this
also cancels the memory position
link setting f or that remote and
restores the default settings. You will also see the ‘‘DRIVER 1’’ or
‘‘DRIVER 2’’ message on the multi-
inf ormation display, depending on
which linked remote transmitter is
used.
1.
2.
Remote Transmitter
Remote Transmitter Care
Replacing the Transmitter
Battery
128
NOTE:
KEYPAD
SCREW
2010 TSX

´
As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.Remove the old battery and note
the polarity. Make sure the
polarity of the new battery is the
same ( side f acing down), then
insert it in the keypad.
Place a cloth on the edge of the
keypad to prevent scratches, and
remove the upper half by carefully
prying on the edge with a small
f lat-tip screwdriver. An improperly disposed of battery
can hurt the environment.
Always conf irm local regulations f or
battery disposal.
Snap the two halves of the keypad,
then install the parts in reverse
order.
4.
5.
3.
Remote Transmitter
Inst rument s and Cont rols
129
BATTERY
2010 TSX

The trunk will lock when you lock
the driver’s door with the key, the
remote transmitter, either master
door lock switch, or the lock tab on
the driver’s door.To open the trunk f rom the outside,
push the release switch, then lif t up.Youcanalsoopenthetrunkineither
of two ways:
Push the trunk release button on
the driver’s door.
Press and hold the trunk release
button on the remote transmitter.
To unlock the trunk, turn the key
twice to unlock the doors, push the
rear of either master door lock
switch, or push UNLOCK twice on
the remote transmitter.
Trunk
130
TRUNK RELEASE
SWITCH
TRUNK RELEASE BUTTON
2010 TSX

To close the trunk, use the inner
handle to lower the lid, then press
down on the back edge.
Keep the trunk lid closed at all times
while driving to avoid damaging it,
and to prevent exhaust gas from
getting into the interior. See,page . To protect items in the trunk, you
can disable the trunk release button
on the driver’s door and the trunk
release switch on the trunk lid by
turning of f the trunk main switch in
the glove box and locking the glove
box. Make sure either rear seat is
not f olded down.
If you need to give the key to
someone else, give them the valet
key. Even if the trunk release is locked
with the main switch, you can open
the trunk with the remote
transmitter.
Your vehicle is equipped with the
emergency f uel lid release in the
trunk. Refer to page for how to
access it.
55 474
Trunk
Carbon
Monoxide Hazard Trunk Main Switch
Emergency Fuel L id Release
Inst rument s and Cont rols
131
MAIN SWITCH
ONOFF
2010 TSX

Store a driving position only when
the vehicle is parked.Turn the ignition switch to the ON
(II) position. You cannot add a
new driving position to the
memory unless the ignition switch
is in the ON (II) position. You can
recall a memorized position with
the ignition switch in any position.
Adjust the seat to a comfortable
position (see page ). Press and release the SET button
on the control panel. You will hear
a beep. Immediately press and
hold one of the memory buttons (1
or 2) until you hear two beeps.
The indicator in the memory
button will come on. The current
position of the driver’s seat is now
stored.
Your vehicle has a memory feature
f or the driver’s seat position.
Two seat positions can be stored in
separate memories. You select a
memorized position by pushing the
appropriate button or using the
appropriate remote transmitter
(Driver 1 or Driver 2).
This setting can be linked or
unlinked with the remote transmitter.
To switch the link setting, see page
. 3.
1.
2.
134
93
All models except Canadian TSX with
4-cylinder engineStoring a Driving Position in
Memory
Driving Position Memory System
142
MEMORY BUTTONS
SET BUTTON
2010 TSX

The system will move the driver’s
seat to the memorized position. The
indicator in the selected memory
button will flash during movement.
When the adjustment is complete,
you will hear two beeps, and the
indicator will stay on.
Fail to press a memory button
within 5 seconds.
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory. If
you want to add a new position while
retaining the current one, use the
other memory button. To select a memorized position, do
this:
To cancel the storing procedure
af ter pressing the SET button, do
any of the f ollowing:
Readjust the seat position.
Turn the ignition switch out from
the ON (II) position.
Make sure the parking brake is set
and the shif t lever is in Park
(automatic).If the parking brake is not set, you
must press and hold the memory
button until the adjustment is
complete.
Press the desired memory button
(1 or 2) until you hear a beep, then
release the button.
1.
2.
On vehicles with manual transmission
CONT INUED
Selecting a Memorized Position
Driving Position Memory System
Inst rument s and Cont rols
143
MEMORY BUTTONS
2010 TSX

Press the UNLOCK button a
second time, and hold it. The
remaining doors unlock, and all
f our windows and the moonroof
start to open. To stop the windows
and moonroof , release the button.Turn the key clockwise, then
release it. Insert the key in the driver’s door
lock.
To open:
Press the UNLOCK button once
to unlock the driver’s door. To open the windows and
moonroof f urther, press the
button again (within 10 seconds of
step 1) and hold it. If the windows
and the moonroof stop bef ore the
desired position, repeat steps 1
and 2.
You cannot close the windows or the
moonroof with the remote
transmitter.
You can open all of the windows and
the moonroof f rom outside with the
remote transmitter. You can open and close the windows
and moonroof with the key in the
driver’s door lock.
1. 2.
3.
1.
2.
CONT INUED
Power Windows
Opening the Windows and
Moonroof with the Remote
Transmitter Opening/Closing the Windows
and Moonroof with the K ey
Inst rument s and Cont rols
149
Open
Close
UNLOCK
BUTTON
2010 TSX