2010 Acura TL Owner's Manual

You can start the engine in any
power mode.
To start the engine:Depress the brake pedal and press
the engine start/stop button. Move the shift lever to Park (P). Af ter you unlock and open the
driver’s door, you will see the ‘‘TO
START ENGINE:’’ message on the
multi-inf ormation display. The ‘‘TO
TURN ACCESSORY ON:’’ message
will be shown af ter three seconds.
The display switches between the
‘‘TO START ENGINE:’’ and ‘‘TO
TURN ACCESSORY ON:’’ messages
every three seconds.
Apply the parking brake.
Press the clutch pedal down all the
way.
The engine does not start unless
the clutch pedal is pressed.
Press the engine start/stop button.
1.
2. 1.
2.
3.
Automatic Transmission
Manual Transmission
K eyless A ccess System
Starting the EngineStarting Guidance
182
ENGINE START/STOP BUTTON
BRAKE PEDAL
AUTOMATIC TRANSMISSION ENGINE START/STOP BUTTON
MANUAL TRANSMISSION CLUTCH PEDAL
M/TTO START ENGINE:
TO TURN
ACCESSORY ON:
A/T
09/07/29 17:13:34 31TK4610_187
2010 TL

Af ter entering the vehicle, insert the
keyless access remote into the slot
to start the engine (see page ). If the keyless access remote battery
dies, you may have to use the built-in
key to unlock/lock the vehicle. The
built-in key is stored inside the
keyless access remote (see page).
If the steering wheel is locked, the
engine cannot start. The multi-
inf ormation display shows you the
above message and the indicator in
the engine start/stop button blinks.
To unlock the steering wheel, apply
f orce by turning it lef t and right
while pressing the engine start/stop
button at the same time.
the multi-
inf ormation display shows the
‘‘INSERT KEYLESS REMOTE
INTO SLOT’’ message, then the ‘‘TO
START ENGINE:’’ message will be
shown af ter you insert the remote
into the slot. Each time you press the
engine start/stop button, the
‘‘INSERT KEYLESS REMOTE
INTO SLOT’’ message is shown on
the multi-information display if the
remote is not in the slot. 195
191
When the keyless access system mainswitch in the glove box is of f , T o unlock t he st eering wheel
K eyless A ccess System
Inst rument s and Cont rols
183
NOTE:
TO UNLOCK WHEEL
09/07/29 17:13:42 31TK4610_188
2010 TL

To turn the vehicle off when the
vehicle is completely stopped:Shif t to park (P).
Press the engine start/stop button
with your f oot on the brake pedal.
If the shift lever is in neutral, press
the engine start/stop button. If the shif t lever is in any gear
other than neutral, depress the
clutch pedal, then press the engine
start/stop button.
The engine stops and the power
mode switches f rom ON to
VEHICLE OFF (LOCK).
Bef ore leaving the vehicle, make
sure it is of f . You can verif y if the
power is of f by checking the engine
start/stop button LED indicator.
Make sure to press the brake pedal
or set the parking brake bef ore
turning of f the engine. If your f oot is
OFF on the clutch pedal in any gear
position, pressing the engine start/
stop button turns of f the engine, and
thevehiclemaymoveforwardor
backward. You can only place the vehicle in the
VEHICLE OFF (LOCK) mode if the
transmission is in Park. You will see
the ‘‘SHIFT TO PARK’’ message on
the multi-information display if you
press the engine start/stop button to
turn the vehicle of f with the shif t
lever in any other position except f or
P(Park).
1.
2.
Automatic Transmission
Manual Transmission On automatic transmission models
On manual transmission models
Stopping the Engine
K eyless A ccess System
Operat ion Guidance
184
SHIFT TO PARK
A/T model only
A/T model
09/07/29 17:13:55 31TK4610_189
2010 TL

CONT INUED
If the power mode is in ACCESSORY,
you may see the ‘‘ACCESSORY
MODE’’ message on the multi-
inf ormation display.Af ter the driver’s door is opened, you
willseethe‘‘TOTURNVEHICLE
OFF:’’ message on the multi-
inf ormation display. Press the engine
start/stop button twice with your
f oot of f the brake pedal to change
the power mode f rom ACCESSORY
to VEHICLE OFF (LOCK).Press the engine start/stop button
twice with your f oot of f the brake
pedal (automatic transmission) or
the clutch pedal (manual
transmission) to change the power
mode to VEHICLE OFF (LOCK). If you open the driver’s door in the
ACCESSORY mode, a beeper will
sound. You will also see a
‘‘ACCESSORY MODE’’ or ‘‘TO
TURN VEHICLE OFF:’’ message on
the multi-information display.
Bef ore leaving the vehicle, make
sure it is in VEHICLE OFF (LOCK).
All models
K eyless A ccess System
Inst rument s and Cont rols
185
TO TURN VEHICLE OFF
ACCESSORY MODE
09/07/29 17:14:05 31TK4610_190
2010 TL

The engine start/stop button may be
used to stop the engine due to an
emergency situation even while
driving. If you must stop the engine,
do either of the f ollowing operations:Press and hold the engine start/
stop button for three seconds.
Firmly press the engine start/stop
button three times.
Do not press the button while driving
unless it is absolutely necessary f or
the engine to be switched of f . If you are driving, the power mode
switches f rom ON to ACCESSORY
or VEHICLE OFF (LOCK)
whenever you perf orm either
procedure. However, the steering
wheel will NOT lock.
If you cannot stop the engine by
pressing the engine start/stop
button once when the vehicle is
stopped and the shif t lever is in Park
(automatic transmission), do either
emergency engine stop procedure.
In this case, the power mode will
change to VEHICLE OFF (LOCK),
however, the steering wheel may
NOT lock.
K eyless A ccess System
Emergency Engine St op
186
09/07/29 17:14:12 31TK4610_191
2010 TL

CONT INUED
If you take the keyless access
remote out of the vehicle and close
the door with the power mode ON or
ACCESSORY, the inside and outside
beepers sound and a ‘‘KEYLESS
REMOTE NOT DETECTED’’
message will be displayed on the
multi-inf ormation display, and the
doors will not lock.The displayed message goes away
when you bring the remote back
inside the vehicle.
If the engine is running and you take
the remote out of the vehicle, it will
continue to run, and the inside and
outside beepers will sound. Once the
power mode is changed to VEHICLE
OFF (LOCK), the engine will not
restart until you bring back a remote
into the vehicle.
Even when the remote is inside the
vehicle, the beeper may sound when
the location of the remote is not
detected due to surrounding
conditions. It is not a f ailure. Make
sure that you carry the remote with
you. The engine does not start if you push
the engine start/stop button when
theremoteisoutsidethevehicle.
Check where the remote is. Make
sure that the remote is in the vehicle
with you when you operate the
engine start/stop button.
K eyless A ccess System
K eyless Remot e Not Det ect ed
Beeper and Message
Inst rument s and Cont rols
187
09/07/29 17:14:22 31TK4610_192
2010 TL

Thebatteryintheremotenormally
lasts about 2 years. To ensure
maximum battery life, do not store
the remote close to electrical devices
such as computers or TVs. When the
multi-inf ormation display shows
‘‘CHANGE KEYLESS REMOTE
BATTERY,’’ replace the battery as
soon as possible (see page ).If the remote battery becomes weak
and the power door lock/unlock
operation is disabled, you should
insert the remote into the keyless
access remote slot to set the power
mode and start the engine. Af ter
inserting the remote to the slot,
operate the engine start/stop button
as previously described (see pages
and ). For more information
on the keyless access slot, see page .
Inserting the remote does not charge
the remote battery. You should
replace the battery as soon as
possible.
The outside beeper sounds when the
power mode is in ACCESSORY, and
a door is opened, then closed.
175178 182
191
K eyless A ccess System
K eyless Remot e L ow Bat t ery
188
09/07/29 17:14:30 31TK4610_193
2010 TL

This switch is in the glove box. You
can cancel the keyless access system
f eatures, which are locking/
unlocking the doors, unlocking the
trunk, and starting the engine while
carrying the keyless access remote.
To cancel the system, turn the
keyless access system main switch
of f by pushing it down.Turning of f the keyless
access system will disable lockout
prevention.
With the keyless access remote
system main switch of f , you should
insert the keyless access remote into
the keyless remote slot to start the
engine. For more inf ormation, see
page . According to the message on the
multi-inf ormation display, this
indicator has two indications. A
‘‘CHECK KEYLESS ACCESS
SYSTEM’’ message indicates a
problem with the keyless access
system. A ‘‘CHECK KEYLESS
STARTING SYSTEM’’ message
indicates a problem with the keyless
starting system.
This indicator normally comes on f or
several seconds when you change
the power mode to ON.
191
CONT INUED
K eyless A ccess System
K eyless Access Remote System
Main Switch
K eyless Access System
Indicator
Inst rument s and Cont rols
189
NOTE:
OFF
MAIN SWITCH
09/07/29 17:14:40 31TK4610_194
2010 TL