2010 Acura RL clock

To adjust the hour, turn the interface
knob, then press the center of the
interf ace selector.Turn the interface knob to adjust the
minute.
To adjust the minute, turn the
interface knob to the right to display
the adjustment screen f or MINUTE. Press the center of the interf ace
selector to enter the time. The
screen will return to the
screen (see page ). 313
Compass System (U.S. model without navigation system)
Clock
adjustment
314
——y


y
(y
y
2010 RL

The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
When the radiator and engine are
cool, relieve any pressure in the
cooling system by turning the
radiator cap counterclockwise,
without pressing down.
Remove the radiator cap by
pushing down and turning
counterclockwise.
Lift up the lid on the front
bulkhead cover f rom the f ront.
Pourthecoolantslowlyand
caref ully so you do not spill any.
Clean up any spill immediately; it
could damage components in the
engine compartment.
3. 2.
1. 4.
Engine Coolant
456
LID
RADIATOR CAP
RESERVE TANK
——y
y
(y
y
2010 RL

CONT INUED
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it one-
quarter turn counterclockwise.
Remove the left or right side
engine compartment cover f rom
thesideyouareworkingonby
caref ully pulling the cover out (see
page ).
If youarereplacingthebulbon
the driver’s side, remove the
battery cover (see page ).
Your vehicle has halogen high beam
headlight bulbs which are also used
f or the daytime running light.
Handle it by its base and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
2.
3.
1.
451 485
Lights
Replacing a Headlight/Daytime
Running L ight Bulb
Maint enance
463
BULB
CONNECTOR
Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.
——y


y
(yy
2010 RL

Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Turn on the headlights to test the
new bulb. Push the electrical connector back
onto the bulb. Make sure it is on
all the way.Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Push the bulb in slightly, and turn
it counterclockwise.
Remove the left or right side
engine compartment cover f rom
thesideyouareworkingonby
caref ully pulling the cover out (see
page ).
Reinstall the engine compartment
side cover.
(Driver’s side)
Reinstall the battery cover. 2.
1.
4.
5.
6.
7.
8.
3.
451
Lights
Replacing a Front T urn Signal
Light Bulb
464
BULB SOCKET
——y

y
(yy
2010 RL

CONT INUED
Remove the left or right side
engine compartment cover (see
page ).
Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working. Reinstall the engine compartment
side cover.
(Driver’s side)
Reinstall the battery cover.
(Passenger’s side)
Use a f lat-tip screwdriver to
remove the holding clip f rom the
windshield washer reservoir.
1.
2.
5.
6. 7.
8.
4.
451
Lights
Replacing a Front Parking/Side
Marker Bulb
Maint enance
465
——y
y
(yy
2010 RL

Your vehicle uses halogen light
bulbs. When replacing a bulb, handle
it by its plastic case, and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. (Passenger’s side)
Reinstall the windshield washer
reservoir.
Reinstall the engine compartment
side cover.
(Driver’s side)
Reinstall the battery cover.
5.
6.
7.
8.
9.
3.
4.
Lights
ReplacingaFogLightBulb
466
SOCKET
BULB
CLIP
Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.
——y

y
(y
y
2010 RL

Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the f og lights to test the
new bulb.
Reinstall the two undercover bolts
onthesideundercoverand
tighten them securely. Put the
holding clip back on the side
undercover and push on the center
until it locks (the center is f lush
with the head).
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it one-
quarter turn counterclockwise.
Caref ully push up the side under
cover into the bumper. Use a Phillips-head screwdriver to
remove the two undercover bolts,
and remove the holding clip with a
f lat-tip screwdriver. 3.
4. 5.
6.
8. 7.
1.
2.
Lights
Maint enance
467
CLIP CONNECTOR BULB
BOLTS
——y
y
(yy
2010 RL

Open the trunk lid, and remove
the lef t or right maintenance lid.
Remove the mounting nut with an
8mmwrench.Carefully pry in the top or bottom
edge of the trim with a small f lat-
tip screwdriver, and pull the trim
straight back.
Remove the two mounting bolts
with an 8 mm wrench.
Pull the taillight assembly straight
back out of the body.Remove the socket by turning it
one-quarter turn counterclockwise.
Remove the burned out bulb by
pulling it straight out of its socket.
2. 1.
3.
4.
5.6.
7.
Lights
Replacing a Rear Turn Signal
Light Bulb
468
MOUNTING NUT
MAINTENANCE LID TAIL LIGHT TRIMBOLTS
BULB
SOCKET
——y
y
(yy
2010 RL