Page 196 of 330
8181
i
Practical information
Fitting a wheel
Fitting the "space-saver" spare wheel
If your vehicle is fitted with alloy wheels, when tightening the bolts on fitting, it is normal to notice that the washers
do not come into contact with the "space-saver" spare wheel. The wheel is secured by the conical sur face of each bolt.
After changing a wheel
To store the punctured wheel in the boot correctly, first remove the central cover. When using the "space-saver" type spare wheel, do not exceed 50 mph (80 km/h). Have the tightening of the bolts and the pressure of the spare wheel checked by a PEUGEOT dealer or a qualified workshop without delay. Have the punctured wheel repaired and refitted to the vehicle as soon as possible.
List of operations
Put the wheel in place on the hub. Screw in the bolts fully by hand. Pre-tighten the security bolt using the wheelbrace 1 fitted with the security socket 4 . Pre-tighten the other bolts using the wheelbrace 1 only.
Page 197 of 330
182
Practical information
Lower the vehicle fully. Fold the jack 2 and detach it. Tighten the security bolt using the wheelbrace 1 fitted with the security socket 4 . Tighten the other bolts using the wheelbrace 1 only.
Refit the bolt covers on each of the bolts (according to equipment). Store the tools in the box.
Page 201 of 330
186
Practical information
lamps
Turn the wheel fully inwards for easy access to the wheel arch liner. Remove the two fixing screws for the access flap, located in the wheel arch. Pull away the wheel arch liner.
Turn the bulb holder a quar ter of a turn and pull it out. Disconnect the bulb holder connector. Pull the bulb and change it. For reassembly, carry out these operations in reverse order. You may also contact a PEUGEOT dealer or a qualified workshop to have these bulbs replaced.
Page 217 of 330
8201
i!
Practical information
Towing the vehicle
Procedure for having your vehicle towed or for towing another vehicle using a removable towing eye.
Towing your vehicle Towing another vehicle Access to the tools
The towing eye is installed in the boot under the floor. To gain access to it: open the boot, position the floor ver tically, remove the towing eye.
On the front bumper, unclip the cover by pressing at the bottom. Screw the towing eye in fully. Install the towing bar. Switch on the hazard warning lamps on the towed vehicle.
On the rear bumper, unclip the cover by pressing at the bottom. Screw the towing eye in fully. Install the towing bar. Switch on the hazard warning lamps on the towed vehicle.
When towing with all four wheels on the ground, always use a towing bar. When towing with only two wheels on the ground, always use professional lifting equipment. When towing with the engine off, there is no longer any braking or steering assistance.
Place the gear lever in neutral (position N on the electronic gear control gearbox or automatic gearbox). Failure to obser ve this special condition could result in damage to cer tain braking components and the absence of braking assistance the next time the engine is star ted.
Page 222 of 330
8205
Practical information
Accessories
A wide range of accessories and genuine par ts is offer ed by the PEUGEOT dealer network. These accessories and par ts have been tested and app roved for reliability and safety. They are all adapted to your vehicle and benefit from PEUGEOT's recommendation and warranty.
"Comfort":
cool box, smoker's kit, 230 V socket, torch...
"Transport solutions":
booster seats and child seats, boot tray, roof box, ski carrier, towbar-mounted bicycle carrier, towbars (swan-neck, quickly detachable ball, folding), harnesses, sliding floor, utility vehicle conversion kit, ... The trailer towbar and its harness must be
fitted by a PEUGEOT dealer.
"Style":
spoiler, front and rear mud flaps, aluminium gear lever knob, alloy wheels (16", 17", 18", 19"), body kit, door mirror shells, door air deflectors, ...
* To avoid any risk of jamming of the pedals: - ensure that the mat is positioned and secured correctly, - never fit one mat on top of another.
"Safety and security":
speed limiter/cruise control, anti-theft alarm, microwave unit, window etching, wheel security bolts, breathalyser, first aid kit, warning triangle, high visibility vest, stolen vehicle tracking system, winter equipment (17" wheels for snow chains), reversing camera, front and
rear parking sensors, boot spacers...
"Protection":
mats * , seat covers, vehicle covers, sun blinds, boot net, load protection net, dog guard, door and boot sill protectors, resin side rubbing strips...
Page 243 of 330
10
227
i
Technical data
I d e n t i fi c a t i o n m a r k i n g s
A. Vehicle Identification Number (VIN) under the bonnet.
This number is engraved on the bodywork near the damper suppor t.
The tyre pressures must be checked when the tyres are cold, at least once a month.
If the tyre pressures are too low, this increases fuel consumption. B. Vehicle identification Number (VIN) on the windscreen lower crossmember. This number is indicated on a self-adhesive label which is visible through the windscreen.
C. Manufacturer’s label. The VIN is indicated on a self-destroying
label affixed to the door aper ture, on the driver’s side.
D. Tyre/paint label. This label is affixed to the door aper ture, on the driver’s side.
It bears the following information: - the tyre inflation pressures with and without load, - the wheel rim and tyre sizes, - the brands of tyre recommended by the manufacturer, - the inflation pressure of the spare wheel,
- the paint colour code.
Page 280 of 330
266
08
1a
1b
1c
1
2
RADIO
By alphabetical list
Press RADIO or LIST , select the station o f y o u r c h o i c e a n d c o n fi r m .
By automatic frequency search
Press or for the automatic search f o r a l o w e r o r h i g h e r r a d i o f r e q u e n c y .
O r t u r n t h e t h u m b w h e e l o n t h e s t e e r i n g mounted control.
By manual frequency search
Press or to adjust the radio frequency step by step.
Press the button on the numerical keypad to recall a preset station.
Or press then turn the thumb wheel at t h e s t e e r i n g m o u n t e d c o n t r o l s .
SELECTING A STATION
T h e e x t e r n a l e n v i r o n m e n t ( h i l l , b u i l d i n g , t u n n e l , u n d e r g r o u n d c a r p a r k . . . ) m a y i n t e r f e r e w i t h t h e r e c e p t i o n , i n c l u d i n g i n R D S s t a t i o n t r a c k i n g m o d e . T h i s phenomenon is a normal result of the way in which r adio waves are transmitted and does not in any way indicate a fault with the audio system.
PRESETTING A STATION
Press one of the buttons on the numerical keypad for 2 seconds to preset the current station.
A n a u d i b l e s i g n a l c o n fi r m s t h a t t h e station has been preset.
The quality of reception is represented by this symbol.
