2010.5 Peugeot 508 buttons

363
Comfort
Storing driving positions
System which stores the electrical settings of the driver's seat and door mirrors as well as the head-up display settings. It enables you to store up to two positions using the buttons on the side of the driver's seat.
Storing a position
using buttons M/1/2
 Switch on the ignition.  Adjust your seat, the door mirrors and the head-up display.  Press button M , then press button 1 or 2within four seconds. An audible signal indicates that the position has been stored. Storing a new position cancels the previous position.
Recalling a stored position
Ignition on or engine running
 Briefly press button 1 or 2 to recall the corresponding position. An audible signal indicates the end of the
adjustment. You can interrupt the current movement by pressing button M , 1 or 2 or by using one of the seat controls. A stored position cannot be recalled while driving. Recalling stored positions is deactivated 45 seconds after switching off the ignition.
Welcome function
The welcome function assists entry and leaving the vehicle. After switching off the ignition and opening the driver’s door, the seat moves back automatically and then stays in this position, ready for the next entry to the vehicle. When switching on the ignition, the seat moves for ward to the stored driving position. When moving the seat, take care that no person or object hinders the automatic movement of the seat. To activate or deactivate this function, contact a PEUGEOT or a qualified workshop.

80
Comfort
Heating and Ventilation
The air circulating in the passenger compartment is filtered and originates either from the outside via the grille located at the base of the windscreen or from the inside in air recirculation mode.
Controls
The incoming air follows various routes depending on the controls selected by the driver, the front passenger and rear passengers, according to the level of equipment. The temperature control enables you to obtain the level of comfor t required by mixing the air of the various circuits. The air distribution control enables you to select the air vents used in the passenger compar tment by the combined use of the
associated buttons. The air flow control enables you to increase or reduce the speed of the ventilation fan. These controls are grouped together on control panel A on the centre console.
1. Windscreen demisting/defrosting vents. 2. Front side window demisting/defrosting vents. 3. Side adjustable air vents. 4. Central adjustable air vents.
5. Air outlets to the front footwells. 6. Adjustable air vents for the rear passengers. 7. Air outlets to the rear footwells.
Air distribution
System which creates and maintains good conditions of comfor t and visibility in the vehicle's passenger compar tment.

82
Comfort
Manual air conditioning
The air conditioning system operates with the engine running.
1. Temperature adjustment
 Turn the dial from left (cold) to right (hot) to adjust the temperature to your requirements.
2. Air fl ow adjustment
 Press the "full fan" button to increase the air flow.
 Press the "empty fan" button to reduce the air flow.
3. Air distribution adjustment
 press the corresponding button for:
Windscreen and side windows.
Central and side vents.
Footwells.
Depending on your requirements, you can combine two distribution buttons or select the three distribution modes simultaneously.
According to the value selected, the associated line of LEDs fills progressively.

86
!
Comfort
8. Air distribution adjustment
 Press the corresponding button for:
Windscreen and side windows.
Centre and side vents.
Footwells.
To suit your requirements, you can combine two distribution buttons or select the three distribution modes simultaneously.
9. Air fl ow adjustment
 Press this "full fan" button to increase the air flow.
 Press "empty fan" button to reduce the air flow.
10. Air intake/Air recirculation
 Press this "empty fan" air flow button until the fan symbol disappears and "- -" appears.
Switching the system off
 Press this button for recirculation of the interior air. The indicator lamp on the button comes on.
Air recirculation enables the passenger compar tment to be isolated from exterior odours and smoke. It is activated automatically when operating the screenwash.
Avoid driving for long periods with the system off (risk of condensation and deterioration of the air quality). Pressing the "full fan" button reactivates the system with the values in use at the time it was switched off.
The air flow symbol, the fan, fills progressively according to the value requested.
This action switches off all of the functions of the air conditioning system. Temperature related comfort is no longer guaranteed but a slight flow of air, due to the forward movement of the vehicle, can still be felt.
 As soon as possible, press this button again to permit the intake of outside air and prevent the formation of condensation. The indicator lamp in the button goes off.

88
i
i
i
Comfort
5. Automatic visibility programme
6. Mono-zone/Quad-zone
7. Air conditioning On/Off
Manual operation
If you wish, you can change one of settings provided by the system. The other functions will still be controlled automatically. Press one of the Soft /Auto/Fast buttons to return to fully automatic operation.
On entering the vehicle, if the interior temperature is much colder or warmer than the comfor t value, there is no need to change the value displayed in order to obtain the comfor t required. The system corrects the difference in temperature automatically and as quickly as possible.
See "Front demisting-defrosting".
Press this button to apply the driver's comfort setting value to the front and rear passengers (mono-zone). The indicator lamp on the button comes on.
The air conditioning is designed to operate effectively in all seasons, with the windows closed. It allows you:
- in summer, to lower the temperature, - in winter, above 3 °C, to improve demisting per formance.
Switching on Press the "A /C" button, the associated green indicator lamp comes on. The air conditioning does not operate when the air flow control is set to off.
Switching off
 Press the "A /C" button again, the associated green indicator lamp goes off. Switching off the air conditioning may result in some discomfor t (humidity, misting).
For maximum cooling or heating of the passenger compar tment, it is possible to exceed the minimum value 14 or the maximum value 28.  Turn the dial 3 or 4 to the left until "LO" is displayed or to the right until "HI" is displayed.
With Stop & Star t, when demisting has been activated, the STOP mode is not available.

389
Comfort
 Press this "full fan" button to increase the air flow.  Press the corresponding button for:
Windscreen and side windows.
Centre and side vents.
Footwells.
To suit your requirements, you can combine two distribution buttons or select the three distribution modes simultaneously.
 Press "empty fan" button to reduce the air flow.
 Press this "empty fan" air flow button until the fan symbol disappears and "- -" appears.
Automatic air intake modeIt is activated by default with automatic comfor t regulation.
9. Air fl ow adjustment
The symbol for air flow, the fan, fills progressively according to the value requested.
Switching the system off
This action switches off all of the functions of the air conditioning system. Temperature related comfort is no longer assured but a slight flow of air, due to the forward movement of the vehicle, can still be felt. Avoid driving for long periods with the system
off (risk of condensation and deterioration of the air quality). Pressing the "full fan" button reactivates the system with the values in use at the time it was switched off.
10. Air intake/Air recirculation
Air recirculation enables the passenger compar tment to be isolated from exterior odours and smoke. It is activated automatically when operating the screenwash. It is inactive when the ambient temperature is below 5 °C to guard against the risk of misting in the vehicle.  As soon as possible, press this button again to permit the intake of outside air and prevent the formation of condensation. The indicator lamp in the button goes off.

118
i
Driving
Head-up display
System which projects various information onto a smoked strip in the field of vision of the driver so that they do not have to take their eyes off the road. This system operates when the engine is running and the settings are stored when the ignition is switched off.
1. Head-up display on. 2. Head-up display off (long press). 3. Brightness adjustment. 4. Display height adjustment.
Buttons
Once the system has been activated, the following information is grouped together inthe head-up display: A. The speed of your vehicle. B. Cruise control/speed limiter information.
Displays during operation
C. Navigation information (according to version).
For more information on the navigation system, refer to the "Audio and telematic" section.

4119
i
!
Driving
With the engine running, press button 1 to activate the system and deploy the strip.  Press and hold button 2 to deactivate the system and retract the strip. The activated/deactivated state is saved and restored on restar ting the engine.
Activation/Deactivation
 With the engine running, adjust the brightness of the information displayed using buttons 3 : - the "sun" to increase the brightness, - the "moon" to decrease the brightness.
Brightness adjustment
We recommend that adjustments are made using these buttons only when the vehicle is stationary. When stationary or while driving, no
objects should be placed around the strip (or in its recess) so as to not impede deployment of the strip and its correct operation.
In cer tain extreme weather conditions (rain and/or snow, bright sunshine, ...) the head-up display may not be legible or may suffer temporary inter ference. Cer tain glasses (sunglasses, spectacles or polarised lenses) may hamper reading of the information. To clean the strip, which is made of organic glass, use a clean, soft cloth (such as a spectacles cloth or microfibre cloth). Do not use a dry or abrasive cloth or detergent or solvent products as these could scratch the strip or damage the non-reflective coating.
Height adjustment
 With the engine running, adjust the display to the desired height using buttons 4 : - up to move the display up,
- down to move the display down.