Page 206 of 345
PRACTICAL INFORMATION
172
TEMPORARY PUNCTURE REPAIR KIT
Complete system consisting of a com-
pressor and a sealant cartridge which
permits the temporary repair of a tyre so
that you can drive to the nearest garage.
It is designed to repair most punctures
which could affect the tyre, located on
the tyre tread or shoulder.
A l l o f t h e s e t o o l s a r e s p e c i fi c t o y o u r
vehicle. Do not use them for other
purposes.
1. 12 V compressor.
Contains a sealant cartridge for the temporary repair of a tyre and
can be used to adjust the tyre
pressures.
2. Two chocks to chock the vehicle.
3. Socket for security bolts (located
in the glove box * ).
For adapting the wheelbrace to the special security bolts.
List of tools Other accessories
4. Removable towing eye.
Refer to "Electric parking brake"
in the "Driving" section.
Refer to the paragraph "Towing
the vehicle".
5. Electric parking brake emergency
release control.
Access to the kit
(5 SEAT VERSION)
The kit is located in the boot under the
concertina board.
Tools
4 and 5 are located in the boot
interior trim, on the left-hand side.
* Depending on destination country.
Page 212 of 345
PRACTICAL INFORMATION
178
CHANGING A WHEEL *
The tools 2 to 4 are installed in a box,
in the middle of the spare wheel, placed
underneath the vehicle.
The tools 1 and 6 to 9 are installed un-
der the concertina boards, in the boot
inner trim.
To gain access to them:
open the boot,
raise the concertina boards.
Access to the tools
Procedure for changing a faulty wheel
for the spare wheel using the tools pro-
vided with the vehicle.
A l l o f t h e s e t o o l s a r e s p e c i fi c t o y o u r
vehicle. Do not use them for other
purposes.
List of tools *
1. Wheelbrace.
For removing the wheel trim and t h e w h e e l fi x i n g b o l t s .
2. Jack with integral handle.
For raising the vehicle.
3. "Bolt cover" tool (according to
equipment).
For removing the bolt protectors (covers) on alloy wheels.
4. Centring guide.
F o r r e fi t t i n g a n a l l o y w h e e l t o t h e hub.
5. Socket for the security bolts (lo-
cated in the glove box).
For adapting the wheelbrace to the special security bolts.
6. Two chocks to immobilise the ve-
hicle.
7. Wheelbrace extension.
For unscrewing/tightening the spare wheel carrier drive.
* Depending on destination country.
Page 216 of 345
PRACTICAL INFORMATION
182
Parking the vehicle
Immobilise the vehicle where
i t d o e s n o t b l o c k t r a f fi c : t h e
ground must be level, stable and
non-slippery ground.
Apply the parking brake unless it
has been programmed to automatic
mode, switch off the ignition and en-
g a g e fi r s t g e a r * t o l o c k t h e w h e e l s .
Check that the braking warning lamp
and the P warning lamp on the park-
ing brake control come on.
If necessary, place a chock under the
wheel diagonally opposite the wheel
to be changed.
The occupants must get out of the ve-
hicle and wait where they are safe.
Never go underneath a vehicle raised
using a jack; use an axle stand.
Removing a wheel
List of operations
Remove the chromed bolt cover
from each of the bolts using the
tool 3 (according to equipment).
Fit the security socket 5 on the
wheelbrace 1 to slacken the security
bolt (if your vehicle has them).
Slacken the other bolts using the
wheelbrace 1 only.
Place the jack 2 in contact with one
of the two front A or rear B locations
provided on the underbody, which-
ever is closest to the wheel to be
changed.
Extend the jack 2 until its base plate
is in contact with the ground. Ensure
that the centreline of the jack base
plate is directly below the location A
or B used.
Raise the vehicle until there is suf-
fi c i e n t s p a c e b e t w e e n t h e w h e e l a n d
the ground to admit the spare (not
punctured) wheel easily.
Remove the bolts and store them in
a clean place.
Remove the wheel.
* position R for the electronic gear
control manual gearbox; P for the
automatic gearbox.
Page 217 of 345
PRACTICAL INFORMATION
After changing a wheel
To store the punctured wheel in the boot
c o r r e c t l y , fi r s t r e m o v e t h e c e n t r a l c o v e r .
When using the "space-saver" type
spare wheel, do not exceed 50 mph
(80 km/h).
Have the tightening of the bolts and the
pressure of the spare wheel checked
by a PEUGEOT dealer without delay.
Have the punctured wheel repaired
and replace it on the vehicle as soon
as possible.
Fitting a wheel
List of operations
Put the wheel in place on the hub
using the centring guide 4 .
Screw in the bolts by hand to the
stop.
Using the wheelbrace 1 fi t t e d w i t h
the security socket 5 , pre-tighten
the security bolt (if your vehicle has
them).
Pre-tighten the other bolts using the
wheelbrace 1 only.
Lower the vehicle fully.
Fold the jack 2 and detach it.
Using the wheelbrace 1 fi t t e d w i t h
the security socket 5 , tighten the
security bolt (if your vehicle has
them).
Tighten the other bolts using the
wheelbrace 1 only.
R e fi t t h e c h r o m e d b o l t c o v e r s o n
each of the bolts (according to
equipment).
Store the tools in the box.
Fitting the "space-saver"
spare wheel
I f y o u r v e h i c l e i s fi t t e d w i t h a l -
loy wheels, when tightening the bolts
o n fi t t i n g i t i s n o r m a l t o n o t i c e t h a t t h e
washers do not come into contact
with the "space-saver" spare wheel.
The wheel is secured by the conical
contact of each bolt.