2010.5 Citroen DS4 change wheel

1. Cruise control or speed limiter settings. 2. Engine oil level indicator. Reminder of ser vicing information. These functions are displayed successively on switching on the ignition, after the welcome sequence and before display of the available active functions. Aler t or information messages may appear temporarily.
Central colour screen associated with the satellite
navigation system
Rotation of the thumb wheel, located on the left of the steering wheel, allows the permanent display to be selected from the available active functions (trip computer, navigation-guidance...).
Approaching the maximum engine speed, the bars are displayed in red and flash, to indicate to you the need to change up a gear.
Rev counter

55Monitoring
Lighting dimmer
Permits manual adjustment of the brightness of the instruments and controls in relation to the exterior brightness. Only operates when the vehicle lighting is on in night mode.
Activation
 Press button A to change the brightness of the instruments and controls.  When the lighting reaches the minimum setting, release the button, then press again to increase it. or  When the lighting reaches the maximum setting, release the button, then press again to reduce it.  When the lighting reaches the level of brightness required, release the button.
This indicator and the lighting
value appear in the middle of the instrument panel during adjustment to show the lighting level compared to the 16 levels available.
You can also modify the level of lighting by turning the thumb wheel B , located on the left of the steering wheel:  upwards; to reduce the level,  downwards; to increase the level.
Deactivation
When the vehicle lighting is off, or in day mode (daytime running lamps on), pressing the button or turning the thumb wheel does not have any effect.

Tyre under-infl ation detection
System which automatically and continuously checks the pressure of the tyres while driving. Sensors fitted in each valve trigger a warning in the event of problem (speed above 12 mph (20 km/h)).
Puncture
The tyre under-inflation detection system is an aid to driving which does not replace the need for the driver to be vigilant or to drive responsibly.
Under-infl ated tyre
This warning lamp is displayed on the instrument panel and/or a message appears in the screen, accompanied by an audible
signal, to identify the wheel concerned.
The STOP warning lamp comes on and/or this warning lamp is displayed on the instrument panel, accompanied by
an audible signal and a message in the screen identifying the wheel concerned.
 Stop as soon as it is safe to do so, avoiding any sudden movement of the steering wheel and the brakes.  Repair or change the damaged wheel (punctured or very deflated tyre), and have the tyre pressure checked as soon as possible.
 Check the tyre pressures as soon as possible. This check must be carried out when the tyres are cold.

201Driving
Six-speed electronic gearbox system which offers a choice between the comfor t of fully automatic operation or the pleasure of manual gear changing. There are two driving modes:
- automatic mode for automatic control of the gears by the gearbox, - manual mode for sequential gear changing by the driver. In automatic mode, it remains possible to change gear manually by using the steering mounted control paddles, when over taking, for example.
6-speed electronic gearbox system
R. Reverse  With your foot on the brake, lift the lever and push for wards. N. Neutral.
 With your foot on the brake, select this position to star t. A. Automatic mode.
 Move the lever backwards to select this mode. M. Manual mode with sequential gear changing.  Move the lever backwards then to the left to select this mode, then use the steering mounted control paddles to change gear.
Gear lever
+. Change up paddle to the right of the steering wheel.  Press the back of the "+" steering mounted paddle to change up a gear.
-. Change down paddle to the left of the steering wheel.  Press the back of the "-" steering mounted
paddle to change down a gear.
Steering mounted control paddles
The steering mounted paddles cannot be used to select neutral or to engage or disengage reverse gear.

Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not block traffic: the ground must be level, stable and non-slippery ground. Apply the parking brake unless it has been programmed to automatic mode, switch off the ignition and engage first gear * to lock the wheels. Check that the braking warning lamps in the instrument panel are on (not flashing). If necessary, place a chock under the wheel diagonally opposite the wheel to be changed. The occupants must get out of the vehicle and wait where they are safe. Never go underneath a vehicle raised using a jack; use an axle stand.
List of operations
 Remove the chromed bolt cover from each of the bolts using the tool 3 (according to
equipment).  Fit the security socket 4 on the wheelbrace 1 to slacken the security bolt.
 Slacken the other bolts using the wheelbrace 1 only.
* position R for the electronic gearbox system.

247Practical information
 Place the jack 2 in contact with one of the two front A or rear B locations provided on the underbody, whichever is closest to the wheel to be changed.  Extend the jack 2 until its base plate is in contact with the ground. Ensure that the centreline of the jack base plate is directly below the location A or B used.  Raise the vehicle until there is sufficient space between the wheel and the ground to admit the spare (not punctured) wheel easily.
 Remove the bolts and store them in a clean place.  Remove the wheel.