Page 46 of 341
5. Air conditioning On/Off
Press this button to switch off the air conditioning.
Switching the system off could result in discomfor t (humidity, condensation). Press this button again to return to automatic operation of the air conditioning. The indicator lamp on the "A /C" button comes on.
6. Air distribution adjustment
Press one or more buttons to
direct the air flow towards:
- the windscreen and side windows (demisting or defrosting), - the outer and centre air vents, - the footwells. You can combine the three orientations to obtain the desired air distribution.
7 . A i r fl o w a d j u s t m e n t
Turn this control to the left to decrease the air flow or to the right to increase the air flow.
8. Air intake/Air recirculation
Press this button for recirculation
of the interior air. The indicator lamp in the button comes on.
The air flow indicator lamps, between the two fans, come on progressively in relation to the value requested.
9. "REST" function: ventilation w i t h t h e e n g i n e o f f
Even with the engine is off, you can operate the ventilation for a few minutes.
Air recirculation enables the passenger compar tment to be isolated from exterior odours and smoke. As soon as possible, press this button again to permit the intake of outside air and prevent the formation of condensation. The indicator lamp in the button goes off.
For example, while you are away from the vehicle, the passengers can still enjoy some air circulation without having the engine running. This function is available after switching on the ignition, as well as after stopping the engine. The period that the function is available depends on the state of charge of the battery. You can activate the "REST" function while the air conditioning control screens are on.
Page 49 of 341
85Comfort
Rear screen demist - defrost
The control button is located on the air conditionin g system control panel.
S w i t c h i n g o n
The rear screen demisting/defrosting can only operate when the engine is running. Press this button to demist /defrost the rear screen and (depending on version) the door mirrors. The indicator lamp associated with the button comes on.
S w i t c h i n g o f f
The demisting/defrosting switches off automatically to prevent an excessive consumption of current. It is possible to stop the demisting/defrosting operation before it is switched off automatically by pressing the button again. The indicator lamp associated with the button goes off.
Switch off the demisting/defrosting of the rear screen and door mirrors as soon as appropriate, as lower current consumption results in reduced fuel consumption.
Page 51 of 341
Heated seats control
With the engine running, the front seats can be heated separately. Use the adjustment dial, placed on the side of each front seat, to switch on and select the level of heating required: 0: Off. 1: Low. 2: Medium. 3: High.
Additional adjustments
H e a d r e s t r a i n t h e i g h t a n d a n g l e adjustment
To raise a head restraint, pull it upwards. To remove the head restraint, press the lug A and pull the head restraint upwards. To put the head restraint back in place, engage the head restraint stems in the openings keeping them in line with the seat back. To lower the head restraint, press the lug Aand the head restraint at the same time. To adjust the angle of the head restraint, tilt its lower par t for wards or rear wards.
The head restraint is fitted with a frame with notches which prevents it from lowering; this is a safety device in case of impact. T h e a d j u s t m e n t i s c o r r e c t w h e n t h e u p p e r e d g e o f t h e h e a d r e s t r a i n t i s l e v e l w i t h t h e t o p o f t h e h e a d . Never drive with the head restraints removed; they must be in place and
adjusted correctly.
Page 52 of 341
Comfort
Manual lumbar adjustment
Turn the knob to obtain the desired level of lumbar suppor t.
Electric lumbar adjustment
Press the front or rear of the control to obtain the desired lumbar suppor t.
This function provides a back massage; it only operates when the engine is running. Press the switch to activate the function. The warning lamp on the switch comes on and the massage function is activated for a period of 60 minutes. During this time, massage is per formed in 6 cycles of 10 minutes each cycle (6 minutes of massage followed by 4 minutes break). After an hour, the function is automatically
deactivated. The warning lamp in the switch goes off.
Deactivation
You can deactivate the massage function at any time by pressing the switch. The movement in progress continues until the initial
non-massage position is reached.
Massage function
Page 54 of 341
Heated seats control
With the engine running, the front seats can be heated separately. Use the adjustment dial, placed on the side of each front seat, to switch on and select the level of heating required: 0: Off. 1: Low. 2: Medium. 3: High.
Additional adjustments
H e a d r e s t r a i n t h e i g h t a n d a n g l e adjustment
To raise a head restraint, pull it upwards. To remove the head restraint, press the lug A and pull the head restraint upwards. To put the head restraint back in place, engage the head restraint stems in the openings keeping them in line with the seat back. To lower the head restraint, press the lug Aand the head restraint at the same time. To adjust the angle of the head restraint, tilt its lower par t for wards or rear wards.
The head restraint is fitted with a frame with notches which prevents it from lowering; this is a safety device in case of impact. T h e a d j u s t m e n t i s c o r r e c t w h e n t h e u p p e r e d g e o f t h e h e a d r e s t r a i n t i s l e v e l w i t h t h e t o p o f t h e h e a d . Never drive with the head restraints removed; they must be in place and
adjusted correctly.
Page 55 of 341
Comfort
Manual lumbar adjustment
Turn the knob to obtain the desired level of lumbar suppor t.
Electric lumbar adjustment
Press the front or rear of the control to obtain the desired lumbar suppor t.
This function provides a back massage; it only operates when the engine is running. Press the switch to activate the function. The warning lamp on the switch comes on and the massage function is activated for a period of 60 minutes. During this time, massage is per formed in 6 cycles of 10 minutes each cycle (6 minutes of massage followed by 4 minutes break). After an hour, the function is automatically
deactivated. The warning lamp in the switch goes off.
Deactivation
You can deactivate the massage function at any time by pressing the switch. The movement in progress continues until the initial
non-massage position is reached.
Massage function
Page 59 of 341
Mirrors
Each fitted with an adjustable mirror glass permitting the lateral rear ward vision necessary for over taking or parking. They can also be folded for parking in confined spaces.
D e m i s t i n g - D e f r o s t i n g
Adjustment
Move control A to the right or to the left to select the corresponding mirror. Move control B in all four directions to adjust. Return control A to the central position.
Door mirrors
The objects obser ved are, in reality, closer than they appear. Take this into account in order to correctly judge the distance of vehicles approaching from behind.
Folding
From outside: lock the vehicle using the remote control or the key. From inside: with the ignition on, pull control A rear wards.
Unfolding
From outside: unlock the vehicle using the remote control or the key. From inside: with the ignition on, pull control A rear wards.
If the mirrors are folded using control A , they will not unfold when the vehicle is unlocked. Pull again on control A .
The folding and unfolding of the door mirrors using the remote control can be deactivated by a CITROËN dealer.
Never fold or unfold the electric folding mirrors manually.
If your vehicle is fitted with heated mirrors, the demisting-defrosting operates with the engine running, by switching on the heated rear screen (refer to the "Rear screen demist-
defrost" page).
Page 60 of 341
93Comfort
Automatic tilting in reverse gear
System which provides a view of the ground during parking manoeuvres in reverse gear.
Programming
With the engine running, engage reverse gear. Select and adjust the left-hand and right-hand mirrors in succession. The adjustment is stored immediately.
S w i t c h i n g o n
With the engine running, engage reverse gear. Move control A to the right or to the left to select the corresponding mirror. The glass of the mirror selected tilts downwards, in accordance with its programming.
S w i t c h i n g o f f
Exit reverse gear and wait ten seconds. or Return control A to the central position. The mirror glass returns to its initial position. The mirror glass also returns to its initial position: - if the speed exceeds 6 mph (10 km/h), - if the engine is switched off.
