2010.5 Citroen DS4 DAG ESP

Warning lampis onCauseAction/Obser vations
Anti-lock Braking System (ABS) fixed. The anti-lock braking system has a fault. The vehicle retains conventional braking. Drive carefully at reduced speed and contact a CITROËN dealer or a qualified workshop without delay.
Dynamic stability control (ESP/ASR)
flashing. The ESP/ASR regulation is active. The system optimises traction and improves the directional stability of the vehicle.
fixed. Unless it has been deactivated (button pressed and its indicator lamp on), the ESP/ASR or hill star t assist system has a fault.
Have it checked by a CITROËN dealer or a qualified workshop.
Low fuel level fixed with the two last bars flashing. When it first comes on there remains approximately 6 litres of fuel in the tank.
You must refuel as soon as possible to avoid running out of fuel. This warning lamp will come on every time the ignition is switched on, until a sufficient addition of fuel is made. Fuel tank capacity: approximately 60 litres. Never continue to drive until you run out of fuel a s this could damage the emission control and injection systems.
Engine autodiagnosis system
fixed. The emission control system has a fault. The warning lamp should go off when the engine is started. If it does not go off, contact a CITROËN dealer or qualified workshop without delay.
flashing. The engine management system has a fault. Risk of destruction of the catalytic conver ter. Have it checked by a CITROËN dealer or a qualified workshop.

Warning lampis onCauseAction/Obser vations
Left-hand
direction indicator
flashing with buzzer. The lighting stalk is pushed down.
Right-hand direction indicator flashing with buzzer. The lighting stalk is pushed up.
Sidelamps fixed. The lighting stalk is in the "Sidelamps" position.
Dipped beam headlamps fixed. The lighting stalk is in the "Dipped beam headlamps" position.
Main beam headlamps fixed. The lighting stalk is pulled towards you. Pull the stalk to return to dipped beam headlamps.
Front foglamps fixed. The front foglamps are switched on. Turn the ring on the stalk rear wards twice to switch off the front foglamps.
Rear foglamps fixed. The rear foglamps are switched on. Turn the ring on the stalk rear wards to switch off the rear foglamps.
Hazard warning lamps flashing with audible signal. The hazard warning lamps switch, located on the dashboard, has been operated.
The left-hand and right-hand direction indicators a nd their associated indicator lamps flash simultaneously.
Operation indicator lamps
If one of the following indicator lamps comes on, this confirms that the corresponding system has come into o peration. It may be accompanied by an audible signal and a message on the multifunction screen.

49Monitoring
Passenger's
airbag system
fixed in the seat belt
and front passenger's airbag warning lamps display.
The control switch, located in the
glove box, is set to the OFF position. The passenger's front airbag is deactivated.
Set the control to the ON position to activate the
passenger's front airbag. In this case, do not fit a child seat in the rear-facing position.
Warning lampis onCauseAction/Obser vations
ESP/ASR fixed. The button, located at the bottom left of the dashboard, is pressed. Its indicator lamp is on. The ESP/ASR is deactivated. ESP: electronic stability programme. ASR: anti-skid regulation.
Press the button to activate the ESP/ASR. Its indica tor lamp goes off. The ESP/ASR system is activated automatically when the vehicle is star ted. If deactivated, the system is reactivated automatical ly from around 30 mph (50 km/h).
Deactivation indicator lamps
If one of the following indicator lamps comes on, this confirms that the corresponding system has been switch ed off intentionally. This is may be accompanied by an audible signal and a message on the multifunction screen.

Monitoring
Manual test in the central colour screen associated with the satellite navigation system
This function allows you to check the status of the vehicle systems (reminder of the "activated"/"deactivated " status of the configurable functions) and to display the aler ts log.
 With the engine running, to star t a manual test, briefly press the ".../000" button on the instrument panel.
The following information appears successively in the instrument panel central colour screen: - engine oil level indicator (see corresponding section),
- ser vice indicator (see corresponding section), - under-inflation detection (if your vehicle
is fitted with this system; see the "Safety" section), - current warnings and aler t messages, if any (see corresponding section for the warning lamp or system concerned), - status of configurable functions (see
"Multifunction screens").
This information also appears every time the ignition is switched on (automatic test).

Colour screen and map
It displays the following information automatically and directly: - time, - date, - altitude, - ambient temperature (the value displayed flashes if there is a risk of ice),
- parking sensor information, - audio functions, - directory and telephone information,
- satellite navigation system information.
Displays in the screen
From the navigation system control panel, to select one of the applications:  press the dedicated "R ADIO" , "MUSIC" , "NAV" , "TR AFFIC" , "PHONE" or "SETUP" button for access to the corresponding menu,  turn the wheel A to select a function, an item in a list,  press button B to confirm the selection, or
 press the "ESC" button to abandon the current operation and return to the previous display.
Controls
For more information on these applications, refer to the "Audio and Telematics" section.

81Comfort
2. Driver's side adjustment 4. Automatic visibility programme
For maximum cooling or heating of the passenger compar tment, it is possible to exceed the minimum value 14 or the maximum value 28.  Turn control 2 or 3 to the left until
"LO" is displayed or to the right until "HI" is displayed.
See "Front demisting - defrosting". 3. Passenger's side adjustment
The driver and front passenger can each adjust the temperature to their requirements. The value indicated on the display corresponds to a level of comfor t and not to a temperature in degrees Celsius or Fahrenheit.
 Turn control 2 or 3 to the left or to the right respectively to decrease or increase this
value.
A setting around the value 21 provides optimum comfort. However, depending on your requirements, a setting between 18 and 24 is normal. You are advised to avoid a left /right setting difference of more than 3.
Manual operation
If you wish, you can make a different choice from that offered by the system by changing a setting. The the "AUTO" indicator lamps go off; the other functions will still be controlled automatically.  Pressing the "AUTO" button returns the system to completely automatic operation.
With Stop & Star t, when demisting has been activated, the STOP mode is not available.

Storing driving positions
System which registers the electrical settings of the driver's seat and door mirrors. It enables you to store and recall two positions using the buttons on the side of the driver's seat.
Storing a position
Using buttons M/1/2
 Switch on the ignition.  Adjust your seat and the door mirrors.  Press button M , then press button 1 or 2within four seconds. An audible signal indicates that the position has been stored.
Recalling a stored position
Ignition on or engine running
 Press button 1 or 2 to recall the corresponding position. An audible signal indicates the end of the adjustment.
Storing a new position cancels the previous position.
You can interrupt the current movement by pressing button M , 1 or 2 or by using one of the seat controls. A stored position cannot be recalled
while driving. Recalling stored positions is deactivated 45 seconds after switching off the ignition.

91Comfort
Rear seats
Bench seat with fixed one-piece cushion and split b ackrest (left hand 2/3, right hand 1/3) which can be folded individually to adapt the load space in the boot.
 Move the corresponding front seat for ward if necessary.  Position the seat belt between the outer and centre head restraints to avoid trapping the belt when repositioning the seat backrest.  Place the head restraints in the low position.
Folding the backrest
 Pull control 1 for wards to release the seat back 2 .  Fold the seat back 2 on to the cushion.
 Straighten the seat back 2 and secure it.  Check that the red indicator, located next to the control 1 , is no longer visible.  Put the seat belt back in place on the side of the seat backrest.
Repositioning the seat backrest
When repositioning the seat backrest, take care not to trap the seat belts.