2010.5 Citroen C4 PICASSO DAG lock
[x] Cancel search: lockPage 112 of 355
V
101
V I S I B I L I T Y
Special position of the
windscreen wipers
This position permits release of the
windscreen wiper blades.
It is used for cleaning or replacement
of the blades. It can also be useful,
in winter, to detach the blades from
the windscreen.
In the moment following switching
off of the ignition, any action on the
stalk positions the wipers vertically
on the windscreen. To park the wipers after this has
been done, switch on the ignition
and operate the stalk.
For maintain the effectiveness of
t h e " fl a t - b l a d e " w i p e r b l a d e s , i t i s
advisable to:
- handle them with care,
- clean them regularly using soapy water,
- avoid using them to retain card- board on the windscreen.
- r e p l a c e t h e m a t t h e fi r s t s i g n s of wear.
COURTESY LAMPS
1. Front courtesy lamp
2. Map reading lamps
Front courtesy lamp In this position, the courtesy
lamp comes on gradually: Permanently off.
Permanent lighting.
In permanent lighting mode, differ-
ent lighting times are available:
- with the ignition off, approxi- mately ten minutes,
- in energy economy mode, approximately thirty seconds,
- with the engine running, unlimited.
- when the vehicle is unlocked,
- when a door or the boot is opened,
- when the key is removed from the ignition,
- when the remote control locking button is activated, in order to lo-
cate your vehicle.
It switches off gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- 30 seconds after the last door is closed. Map reading lamps
With the ignition on, press the
corresponding switch.
Panoramic sunroof courtesy
lamps
These courtesy lamps have two oper-
ating modes:
- automatic lighting when a door is opened or when the front cour-
tesy lamp is in the "permanent
lighting" position,
- permanent lighting.
Opening the boot switches on the
third row courtesy lamp and the boot
lamps.
Page 118 of 355
VI
107
F I T T I N G S
AIRCRAFT-STYLE REAR TABLES
Rear table stowed
Rear table opened
The backrests of the front seats are
fi t t e d w i t h a i r c r a f t - s t y l e t a b l e s . T h e s e
incorporate a cup-holder A and a
retaining strap B , for the placing of
objects.
Pull the table downwards to
open.
To stow the table, raise it until
the latch locks.
For safety reasons, these tables col-
lapse downwards if excessive pres-
sure is exerted on them.
Reading lamps C m a y b e fi t t e d i n
the front seat backrests, behind the
tables. They illuminate the surface
of the tables without disturbing the
other passengers.
They can be used only while the ta-
ble is down.
P r e s s t h e " o n / o f f " b u t t o n t o t u r n
the lamp on or off.
SECOND ROW FOOTWELL
D e p e n d i n g o n t h e c o n fi g u r a t i o n , t h e
vehicle has one or two storage com-
partments under the footwell, locat-
e d b e t w e e n t h e s e a t s o f t h e fi r s t a n d
second rows. They can be accessed
v i a c l i p p e d fl a p s w i t h a h a n d l e A .
The compartment on the left-hand
side may contain the temporary
puncture repair kit and the tool kit
may be stored in the compartment
on the right-hand side. In this case
t h e fl a p i s s e c u r e d b y m e a n s o f a
screw B . To gain access to the com-
partment, turn the screw a quarter
turn anticlockwise using a coin.
O n v e h i c l e s fi t t e d w i t h p n e u m a t i c
s u s p e n s i o n , t h e l e f t - h a n d fl a p i s
locked.
Individual reading lamps
Page 124 of 355
VI
107
F I T T I N G S
AIRCRAFT-STYLE REAR TABLES
Rear table stowed
Rear table opened
The backrests of the front seats are
fi t t e d w i t h a i r c r a f t - s t y l e t a b l e s . T h e s e
incorporate a cup-holder A and a
retaining strap B , for the placing of
objects.
Pull the table downwards to
open.
To stow the table, raise it until
the latch locks.
For safety reasons, these tables col-
lapse downwards if excessive pres-
sure is exerted on them.
Reading lamps C m a y b e fi t t e d i n
the front seat backrests, behind the
tables. They illuminate the surface
of the tables without disturbing the
other passengers.
They can be used only while the ta-
ble is down.
P r e s s t h e " o n / o f f " b u t t o n t o t u r n
the lamp on or off.
SECOND ROW FOOTWELL
D e p e n d i n g o n t h e c o n fi g u r a t i o n , t h e
vehicle has one or two storage com-
partments under the footwell, locat-
e d b e t w e e n t h e s e a t s o f t h e fi r s t a n d
second rows. They can be accessed
v i a c l i p p e d fl a p s w i t h a h a n d l e A .
The compartment on the left-hand
side may contain the temporary
puncture repair kit and the tool kit
may be stored in the compartment
on the right-hand side. In this case
t h e fl a p i s s e c u r e d b y m e a n s o f a
screw B . To gain access to the com-
partment, turn the screw a quarter
turn anticlockwise using a coin.
O n v e h i c l e s fi t t e d w i t h p n e u m a t i c
s u s p e n s i o n , t h e l e f t - h a n d fl a p i s
locked.
Individual reading lamps
Page 128 of 355
VI
111
F I T T I N G S
T h e r o l l e r h a s a m o v i n g fl a p t o
avoid interference with the second-
row passengers when the seats
are in the "reclined" position.
Engage the lug on the left of the
roller in notch C .
Pass the right-hand end above
the third-row armrest.
Engage the lug in notch D .
Pull the seat belt(s) so that they
reel out without locking.
Pull out the blind and engage
the guides into the rails on the
pillars.
Lock the seat(s) in position.
Installing the roller
Reel in the blind, then remove
the roller from its initial position.
Position the roller, with the blind
p u l l b a r u p p e r m o s t , fl a p d o w n -
ward.
Fold the concertina boards.
Removing the roller
P u s h t h e fl a p t o w a r d s t h e s e a t
backrest.
Lift the concertina board by tak-
ing it at the side, then position it
vertically.
Release the seat by pulling the
strap E .
Push the backrest towards the front.
Proceed in reverse order to in-
stalling. Position 3
7 - s e a t c o n fi g u r a t i o n ; s t o w e d b e h i n d
the third row seats when these are
folded away.
Installing the roller
Fold the concertina boards.
Position the roller, with the blind
p u l l b a r u p p e r m o s t , fl a p d o w n -
ward.
Engage the lug on the left of the
roller in notch C .
Pass the right-hand end above
the third-row armrest.
Engage the lug in notch D .
Removing the roller
Proceed in reverse order to in-
stalling.
Position 2
7 - s e a t c o n fi g u r a t i o n ; i n s t a l l e d b e -
hind the third-row seats when these
are folded away. This position con-
ceals objects stowed in the boot
from outside view.
The roller can only be stored when
the seats are folded away.
You can position the concertina
board vertically to lodge a bulky ob-
ject in the boot well.
Page 135 of 355
VI
111
F I T T I N G S
T h e r o l l e r h a s a m o v i n g fl a p t o
avoid interference with the second-
row passengers when the seats
are in the "reclined" position.
Engage the lug on the left of the
roller in notch C .
Pass the right-hand end above
the third-row armrest.
Engage the lug in notch D .
Pull the seat belt(s) so that they
reel out without locking.
Pull out the blind and engage
the guides into the rails on the
pillars.
Lock the seat(s) in position.
Installing the roller
Reel in the blind, then remove
the roller from its initial position.
Position the roller, with the blind
p u l l b a r u p p e r m o s t , fl a p d o w n -
ward.
Fold the concertina boards.
Removing the roller
P u s h t h e fl a p t o w a r d s t h e s e a t
backrest.
Lift the concertina board by tak-
ing it at the side, then position it
vertically.
Release the seat by pulling the
strap E .
Push the backrest towards the front.
Proceed in reverse order to in-
stalling. Position 3
7 - s e a t c o n fi g u r a t i o n ; s t o w e d b e h i n d
the third row seats when these are
folded away.
Installing the roller
Fold the concertina boards.
Position the roller, with the blind
p u l l b a r u p p e r m o s t , fl a p d o w n -
ward.
Engage the lug on the left of the
roller in notch C .
Pass the right-hand end above
the third-row armrest.
Engage the lug in notch D .
Removing the roller
Proceed in reverse order to in-
stalling.
Position 2
7 - s e a t c o n fi g u r a t i o n ; i n s t a l l e d b e -
hind the third-row seats when these
are folded away. This position con-
ceals objects stowed in the boot
from outside view.
The roller can only be stored when
the seats are folded away.
You can position the concertina
board vertically to lodge a bulky ob-
ject in the boot well.
Page 147 of 355
VII
122
C H I L D S A F E T Y
MANUAL CHILD LOCK
Locking
U s i n g t h e i g n i t i o n k e y , t u r n t h e
r e d c o n t r o l o n e e i g h t h o f a t u r n ,
f o l l o w i n g t h e i n s t r u c t i o n s o n t h e
l a b e l .
Unlocking
U s i n g t h e i g n i t i o n k e y , t u r n t h e
r e d c o n t r o l o n e e i g h t h o f a t u r n
t o r e t u r n t o t h e o r i g i n a l p o s i t i o n .
ELECTRIC CHILD LOCK
M e c h a n i c a l s y s t e m t o p r e v e n t o p e n -
i n g o f t h e r e a r d o o r u s i n g i t s i n t e r i o r
c o n t r o l .
T h e c o n t r o l i s l o c a t e d o n t h e e d g e o f
e a c h r e a r d o o r . R e m o t e c o n t r o l s y s t e m t o p r e v e n t
o p e n i n g o f t h e r e a r d o o r s u s i n g t h e i r
i n t e r i o r c o n t r o l s a n d u s e o f t h e r e a r
e l e c t r i c w i n d o w s .
Activation
P r e s s b u t t o n A . Deactivation
P r e s s b u t t o n A a g a i n .
T h i s s y s t e m i s i n d e p e n d e n t o f a n d
i n n o c i r c u m s t a n c e s t a k e s t h e p l a c e
o f t h e c e n t r a l l o c k i n g s y s t e m .
C h e c k t h e s t a t u s o f t h e c h i l d
l o c k e a c h t i m e y o u s w i t c h o n t h e
i g n i t i o n .
A l w a y s r e m o v e t h e k e y f r o m t h e
i g n i t i o n w h e n l e a v i n g t h e v e h i c l e ,
e v e n f o r a s h o r t t i m e .
I n t h e e v e n t o f a s e r i o u s i m p a c t ,
t h e e l e c t r i c c h i l d l o c k i s d e a c t i v a t e d
a u t o m a t i c a l l y t o p e r m i t t h e e x i t o f
t h e r e a r p a s s e n g e r s .
T h i s w a r n i n g l a m p c o m e s
o n t e m p o r a r i l y o n t h e i n s t r u -
m e n t p a n e l w h e n t h e c h i l d
l o c k i s a c t i v a t e d .
I t a l s o c o m e s o n w h e n t h e i g n i t i o n i s
s w i t c h e d o n , t h e n g o e s o f f a p p r o x i -
m a t e l y t e n s e c o n d s a f t e r t h e e n g i n e
i s s t a r t e d .
T h e c o n t r o l i s l o c a t e d o n t h e d r i v e r ' s
d o o r , w i t h t h e e l e c t r i c w i n d o w c o n t r o l s .
Page 150 of 355
VIII
125
S A F E T Y
SYSTEMS
Group of supplementary systems
which help you to obtain optimum
braking in complete safety in emer-
gency situations:
- anti-lock braking system (ABS),
- electronic brake force distribu-tion (EBFD),
- emergency braking assistance (EBA).
Anti-lock braking system
and electronic brake force
distribution
Linked systems which improve the
stability and manoeuvrability of your
vehicle when braking, in particular
on poor or slippery surfaces.
Activation
The anti-lock braking system comes
into operation automatically when
there is a risk of wheel lock.
Normal operation of the ABS may
make itself felt by slight vibration of
the brake pedal. Operating fault
When braking in an emergency,
p r e s s v e r y fi r m l y w i t h o u t r e l e a s i n g
the pressure. If this warning lamp comes
on, accompanied by an au-
dible signal and a message
on the multifunction screen,
it indicates a malfunction of the anti-
lock braking system which could re-
sult in loss of control of the vehicle
when braking.
If this warning lamp comes on,
together with the STOP and
ABS warning lamps, accom-
panied by an audible signal
and a message on the multifunction
screen, it indicates a malfunction of
the electronic brake force distribution
which could result in loss of control of
the vehicle when braking.
You must stop as soon as it is
safe to do so.
In either case, contact a CITROËN
dealer.
When replacing wheels (tyres and
rims), ensure that they conform to the
manufacturer's recommendations.
Emergency braking assistance
System which, in an emergency,
enables you to obtain the optimum
braking pressure more quickly, thus
reducing the stopping distance.
Activation
It is triggered by the speed at which
the brake pedal is pressed.
The effect of this is a reduction in
the resistance of the pedal and an
i n c r e a s e i n b r a k i n g e f fi c i e n c y .
When braking in an emergency,
p r e s s fi r m l y w i t h o u t r e l e a s i n g t h e
pressure.
Page 153 of 355
VIII
128
S A F E T Y
SEAT BELTS
Front seat belts
T h e f r o n t s e a t b e l t s a r e fi t t e d w i t h a
pretensioning system and force limiter.
This system improves safety in the front
seats in the event of a front impact.
Depending on the seriousness of the
impact, the pretensioning system in-
stantly tightens the seat belt against
the body of the occupant. Fastening
Pull the belt down in front of you
in a steady movement, making
sure that it does not become
twisted.
Press the fastening into its buckle.
Check that it is properly secured
and that the automatic locking
mechanism operates correctly
by pulling sharply on the belt
strap.
The lap strap should be posi-
tioned as low down as possible in
the lap and as tight as possible.
The diagonal strap should be
positioned across the chest and
away from the neck.
Each belt has a reel that adjusts its
length automatically to the girth of
the seat occupant. Height adjustment
The pretensioning seat belts are
active when the ignition is on.
The force limiter reduces the pres-
sure of the seat belt against the
chest of the occupant, so increasing
his protection.
When correctly adjusted, the seat
belt shoulder strap falls over the
middle of the shoulder.
To adjust the belt, squeeze the
control and slide it in the direc-
tion required.
Unfastening
To unfasten the belt, press on
the red button in the buckle.
The belt retracts automatically when
not in use.