2010.5 Citroen C3 DAG display
[x] Cancel search: displayPage 12 of 235
FAMILIARISATION
MONITORING
Instrument panel
A. W i t h t h e i g n i t i o n o n , t h e f u e l g a u g e
bars for the fuel remaining should
come on.
B. W i t h t h e e n g i n e r u n n i n g , t h e a s s o c i -
ated low level warning lamp should
go off.
C. W i t h t h e i g n i t i o n o n , t h e o i l l e v e l i n -
dicator should display "OIL OK" for
a few seconds.
I f t h e l e v e l s a r e n o t c o r r e c t , t o p u p t h e
level which is low.
19 Warning lamps
1. W i t h t h e i g n i t i o n o n , t h e o r a n g e a n d
red warning lamps come on.
2. W i t h t h e e n g i n e r u n n i n g , t h e s e
warning lamps should go off.
I f a w a r n i n g l a m p r e m a i n s o n , r e f e r t o
the page concerned.
21, 26 Switch panel
Illumination of the indicator lamp indi-
cates the state of the corresponding
system.
A. ESP/ASR system deactivated.
96
B. Stop & Start system deactivated.
112
Page 15 of 235
FAMILIARISATION Speed limiter "LIMIT"
1. Selecting/Switching off speed limiter
mode.
2. D e c r e a s e t h e p r o g r a m m e d v a l u e .
3. Increase the programmed value.
4. Speed limiter on/off.
114
DRIVING SAFELY
Cruise control "CRUISE"
1. Selecting/Switching off cruise con-
trol mode.
2. D e c r e a s e t h e p r o g r a m m e d v a l u e .
3. Increase the programmed value.
4. Cruise control Off/Resume.
116
The values must be set with the engine
running. Display in the instrument panel
The cruise control or speed limiter mode
appears in the instrument panel when it
is selected.
I n o r d e r t o b e p r o g r a m m e d o r a c t i v a t e d ,
the vehicle speed must be higher than
2 5 m p h ( 4 0 k m / h ) , w i t h a t l e a s t f o u r t h
gear engaged on a manual gearbox
( s e c o n d g e a r o n a S e n s o D r i v e o r a u t o -
m a t i c g e a r b o x ) . Cruise control
Speed limiter
Page 16 of 235
1
MONITORING
Panel grouping together the vehicle operation indication dials and warning lamps.
PETROL - DIESEL MANUAL GEARBOX INSTRUMENT PANELS
5. Display management button
Servicing information.
Adjust the time and choose units.
Reset the service indicator.
6. Instrument panel lighting button.
Adjusts the brightness of the lighting of the instruments and controls.
For more information, refer to the
section on the button or function
and its associated display.
Dials
1. Rev counter.
Indicates the speed of rotation of the engine (x 1 000 rpm).
2. Vehicle speed.
Indicates the current speed of the moving vehicle (mph or km/h).
3. Fuel level.
Indicates the quantity of fuel remain- ing in the tank.
4. Screen.
A. Ambient temperature.
(°Celsius or °Fahrenheit)
B. Gear
e f fi c i e n c y
indicator.
C. Time.
D. Engine oil level indicator.
Appears a few seconds after switching
on the ignition, then disappears.
E. Trip computer.
F. Service indicato
r.
(miles or km) then,
Total mileage.
These two functions are displayed successively when switching on the
ignition.
Screen
Page 17 of 235
1
MONITORING
PETROL - DIESEL MANUAL, SENSODRIVE OR AUTOMATIC
GEARBOX INSTRUMENT PANELS
Panel grouping together the vehicle operation indication dials and warning lamps.
Depending on the version, the instrument panel may have permanent back-lighting.
Dials
1. Rev counter.
Indicates the speed of rotation of the engine (x 1 000 rpm).
2. Vehicle speed.
Indicates the current speed of the moving vehicle (mph or km/h).
3. Fuel level.
Indicates the quantity of fuel remaining
in the tank.
4. Screen.
5. Display management button
Alternates display between range and trip mileage recorder.
Servicing information.
Resets the selected function to zero (trip distance recorder or service in-
dicator).
6. Instrument panel lighting button.
Adjusts the brightness of the lighting of the instruments and controls.
For more information, refer to the
section on the button or function
and its associated display.
A. Speed limiter
(mph or km/h) or
Cruise control.
B. Gear shift indicator.
C. SensoDrive
or
automatic gearbox
information.
D. Range
(miles or km) or
Trip mileage recorder.
E. Service indicator
(miles or km), then
Total mileage recorder
These two functions are displayed successively when switching on the
ignition
F. Engine oil level indicator
Appears a few seconds after switching
on the ignition, then disappears.
Screen
Page 28 of 235
1
MONITORING
Service indicator
System which informs the driver when
the next service is due, in accordance
with the manufacturer's servicing
schedule.
The point at which the service is due is
calculated from the last indicator zero
reset. It is determined by two param-
eters:
- the distance travelled,
- the time elapsed since the last service. Between 600 miles (1 000 km) and
1 800 miles (3 000 km) remain before
the next service is due
For a few seconds after the ignition is
switched on, the spanner symbolising
the service operations comes on. The
distance recorder display line indicates
the distance remaining before the next
service is due.
Example: 1 700 miles (2 800 km) re-
main before the next service is due.
For a few seconds after the ignition is
switched on, the screen indicates:
Less than 600 miles (1 000 km)
remain before the next service is due
Example: 400 miles (900 km) remain
before the next service is due.
For a few seconds after the ignition is
switched on, the display indicates:
A few seconds after the ignition is
switched on, the spanner goes off ; the
distance recorder resumes its normal
operation. The screen then indicates
the total and trip distances.
A few seconds after the ignition is switched on, the distance recorder resumes its nor-
mal operation. The spanner remains on
to indicate that a service must be carried
out soon.
More than 1 800 miles (3 000 km)
remain before the next service is due
When the ignition is switched on, no ser-
vice information appears in the screen.
Page 29 of 235
1
MONITORING
Service overdue
For a few seconds after the ignition is
switched on, t h e s p a n n e r fl a s h e s to
indicate that the service must be carried
out as soon as possible.
Example: the service is overdue by
180 miles (300 km).
For a few seconds after the ignition is
switched on, the display indicates:
A few seconds after the ignition is switched
on, the distance recorder resumes its nor-
mal operation. The spanner remains on .
The distance remaining may be
weighted by the time factor, de-
pending on the driver's driving
habits.
Therefore, the spanner may also
come on if you have exceeded
the two year service interval. Service indicator zero reset
After each service, the service indicator
must be reset to zero.
The procedure for resetting to zero is as
follows:
switch off the ignition,
press and hold the trip distance re-
corder zero reset button,
switch on the ignition; the distance re-
corder display begins a countdown,
when the display indicates "=0" ,
release the button; the spanner dis-
appears. Retrieving the service information
You can access the service information
at any time.
Press the trip distance recorder zero
reset button.
The service information is displayed for a few seconds, then disappears. Following this operation, if you
wish to disconnect the battery,
lock the vehicle and wait at least
fi v e m i n u t e s f o r t h e z e r o r e s e t t o
be taken into account.
Page 30 of 235
1
MONITORING
Service overdue
For a few seconds after the ignition is
switched on, t h e s p a n n e r fl a s h e s to
indicate that the service must be carried
out as soon as possible.
Example: the service is overdue by
180 miles (300 km).
For a few seconds after the ignition is
switched on, the display indicates:
A few seconds after the ignition is switched
on, the distance recorder resumes its nor-
mal operation. The spanner remains on .
The distance remaining may be
weighted by the time factor, de-
pending on the driver's driving
habits.
Therefore, the spanner may also
come on if you have exceeded
the two year service interval. Service indicator zero reset
After each service, the service indicator
must be reset to zero.
The procedure for resetting to zero is as
follows:
switch off the ignition,
press and hold the trip distance re-
corder zero reset button,
switch on the ignition; the distance re-
corder display begins a countdown,
when the display indicates "=0" ,
release the button; the spanner dis-
appears. Retrieving the service information
You can access the service information
at any time.
Press the trip distance recorder zero
reset button.
The service information is displayed for a few seconds, then disappears. Following this operation, if you
wish to disconnect the battery,
lock the vehicle and wait at least
fi v e m i n u t e s f o r t h e z e r o r e s e t t o
be taken into account.
Page 32 of 235
1
MONITORING
Total distance recorder
System which measures the total distance
travelled by the vehicle during its life.
The total and trip distances are dis-
played for thirty seconds when the
ignition is switched off, when the driver's
door is opened and when the vehicle is
locked or unlocked.
With the ignition on, press the button
until zeros appear.
Trip distance recorder
System which measures a distance
travelled during a day or other period
since it was reset to zero by the driver. Clock
Adjusting the time - Choice of units
press the button for more than
two seconds: °C or °F is displayed,
press the button to select °C or °F,
press the button for more than
two seconds to complete the adjust-
ments.
After approximately 30 seconds without
any action, the screen returns to the
normal display.
To adjust the time of the clock and
choose the units used by the screen,
use the right-hand button on the instru-
ment panel, carrying out the operations
in the following order:
press the button for more than
t w o s e c o n d s : t h e m i n u t e s fl a s h ,
press the button to increase the
minutes,
press the button for more than
t w o s e c o n d s : t h e h o u r s fl a s h ,
press the button to increase the hours,
press the button for more than
two seconds: 24 H or 12 H is dis-
played,
press the button to select 24 H or
12 H,