2010.5 Citroen C ZERO bulb

.
.
Contents
1
ISOFIX child seats 65
Child lock 68
Child safety
Direction indicators 69
Hazard warning lamps 69
Horn 69
Emergency or assistance call 70
Braking assistance systems 70
Tr ajectory control systems 72
Front seat belts 73
Airbags 76
Safety
Charging the main battery 80
Ancillaries battery 86
Te m p o r a ry puncture repair kit 90
Changing a wheel 94
Changing a bulb 97
Changing a fuse 105
Changing a wiper blade 110
To w i ng the vehicle 110
Precautions for washing 111
Accessories 111
Practical information
Bonnet 114
Front compartment 115
Rear compartment 116
Checking levels 117
Checks 119
Checks
Electric motor 120
Weights 121
Dimensions 122
Identifi cation markings 123
Technical data
Emergency or assistance 125
Audio system 127
Audio and telematics
Visual search
Alphabetical index

i
i
i
Visibility
58
Daytime running lamps
Special daytime lighting so that the vehicle can
be seen more easily. The daytime running lamps come on automatically when star ting the motor, if no
other lighting is on.
They cannot be deactivated. With the main li
ghting control ring in the AUTO
position, the sidelamps and dipped beam
headlamps come on automaticall
y, without anyaction by the driver, when a low level of ambientlight is detected.
When the light returns to a sufficient level or the
wipers are switched off, the lighting is switched
off automatically.
The sensor is located at the base of the
windscreen.
Automatic illumination of headlamps
Automatic lighting off
When the lighting stalk is in the "dipped or mainbeam headlamps" position, if the ignition switch
is in the "LOCK" or "ACC" position or if thekey has been removed, the lighting switches
off automatically when the driver's door isopened .
The driver is is aler ted by an audible signal. The initial setting is position "0".









Headlamp
adjustment

To avoid causing a nuisance to other road
users, the height of the halogen headlampsshould be adjusted according to the load in the
vehicle. 0. Driver only or driver + 1 front passenger.
1 or 2.
4 people (including the driver). 3.4 people (including the driver) + maximumauthorised load.4.
Driver + maximum authorised load.

Even though these lamps are located inthe same lamp unit as the front foglamp, the operate with a specific bulb.
Their use is covered by road vehiclelighting regulations.
In foggy weather or in snow, thesunshine sensor may detect sufficient light. The lighting will not come on automatically. Do not cover the sunshine sensor, theassociated functions will no longer becontrolled.

8
!
Practical information
97








Changing a bulb
1.Direction indicators(W21W - 21 W).2.Sidelamps (W5W - 5 W).3.Main beam headlamps (HB3 - 60 W).4.Dipped beam headlamps (H11 - 55 W).

The headlamps are fitted with polycarbonate glass with a protectivecoating:)do not clean them using a dry or abrasive cloth, nor with a detergent or solvent product,)
use a sponge and soapy water, )
when using a high pressure washer on persistent marks, do not directat the lamps or their outlines for too long, so as not to damage their protective coating and seals.
)
Do not touch the bulb directly with your fingers, use lint-free cloths.
Changing a bulb should only be done after the headlamp has been switched
off for a few minutes (risk of serious burns). It is imperative to use only anti-ultraviolet (UV) type bulbs in order notto damage the headlamp. Always replace a failed bulb witha new bulb with the same type andspecification.
Front lamps
5. Front foglamps(H8 - 35 W).6.Daytime running lamps (P13W - 13 W).

Practical information
98
) Lift the cover B
, using a screwdriver
protected by a cloth.) Slacken fixing screw C
until the head of the screw touches the trim.
)Remove the bumper retaining clips, usinga screwdriver. )Carefully lift the bumper. To replace a failed bulb,
you must first remove
the lamp. To remove the lamp:)Open the bonnet. )Press tab A to release the connector.
Access to bulbs

i
Practical information
100

Changing a sidelamp bulb
)
Turn the bulb holder to the left and
pull it out.) Pull the bulb out and replace it.
To r efit, carry out these operations in reverseorder.


Changing a main beam headlampbulb
)Turn the bulb holder to the left andpull it out. )Pull the bulb out, pressing its tab. )Replace the bulb.
To r efit, carry out these operations in reverse order.
Changing a direction indicator
bulb
)Turn the bulb holder to the left andremove it.)Pull the bulb and change it.
To r e f i t , c a r ry out these operations in reverse order.
Coloured bulbs must be replaced with bulbs of identical specification andcolour.

8
Practical information
101
Changing a dipped beamheadlamp bulb
)Turn the bulb holder to the left andpull it out. )Remove the bulb by pressing its tab. )Replace the bulb.
To r efit, carry out these operations in reverse order.

Changing a foglamp/daytime running lamp bulb
)
Turn the wheels onto full lock to improveaccess. )
Remove the clips holding the protective cover over the bulb holder. )
Pull the cover away.
)
Turn the bulb holder ( Afor the foglamp, Bfor the daytime running lamps) to the left
and pull it out.
) Pull the bulb out and replace it.
To r e f i t , c a r ry out these operations in reverseorder.

i
i
Practical information
102
1.Brake lamps/Sidelamps (LEDs).2. Direction indicators(W Y21W - 21 W).3.Reversing lamps (W21W - 21 W).
Rear lamps
Amber coloured bulbs, such as the direction indicators, must be replaced with bulbs of identical specification and colour.
In some weather conditions (e.g. lowtemperature or humidity), the presenceof misting on the internal surface of the glass of the headlamps and rear lamps is normal; it disappears after the lampshave been on for a few minutes.
Changing an integrated directionindicator side repeater(WY5W - 5 W)
)Push the repeater towards the rear anddetach it. )Turn the bulb holder to the left andpull it out. )Pull the bulb out and replace it.
To r e f i t , c a r ry out these operations in reverse order.

8
Practical information
103
Changing a direction indicator bulb
) Turn the bulb holder to the left and
pull it out. ) Pull the bulb out and replace it.
To r efit, carry out these operations in reverse order.
Access to bulbs
)Remove the two screws. )Disengage the lamp unit by pulling it
towards you.

Changing a brake/sidelamp bulb

All work on the LED lamps must be carried out
by a CITROËN dealer or a qualified workshop.


Changing a reversing lamp bulb
)
Turn the bulb holder to the left and pull it out.)
Pull the bulb out and replace it.
To r efit, carry out these operations in reverseorder.