2009 YAMAHA YFZ450R engine coolant

8-19
1
2
3
4
5
6
78
9
10
11

minutes while checking it for oil leakage. If oil
is leaking, immediately turn the engine off and
check for the cause.
15. Turn the engine off, and then check the oil lev-
el and correct it if necessary.
16. Install the engine guard by installing the bolts,
and then tighten them to the specified torque.
NOTICE

ECB00370
Be sure to apply LOCTITE® to the engine
guard bolts before installing them.
EBU23470
Coolant
The coolant level should be checked before each
ride. In addition, the coolant must be changed at
the intervals specified in the periodic maintenance
and lubrication chart.
EBU23482
To check the coolant level
1. Place the ATV on a level surface.TIP

The coolant level must be checked on a cold en-
gine since the level varies with engine tempera-
ture.
2. Check the coolant level in the coolant reser-
voir.
TIP

The coolant should be between the minimum and
maximum level marks.
3. If the coolant is at or below the minimum level
mark, remove the reservoir cap, add coolant
or distilled water to the maximum level mark,
and then install the reservoir cap. Tightening torque:
Engine guard bolt:
7 Nm (0.7 m·kgf, 5 ft·lbf)

8-20
1
2
3
4
5
6
78
9
10
11
NOTICE

ECB00401

If coolant is not available, use distilled water
or soft tap water instead. Do not use hard wa-
ter or salt water since it is harmful to the en-
gine.

If water has been used instead of coolant, re-place it with coolant as soon as possible,
otherwise the cooling system will not be pro-
tected against frost and corrosion.

If water has been added to the coolant, have
a Yamaha dealer check the antifreeze con-
tent of the coolant as soon as possible, oth-
erwise the effectiveness of the coolant will
be reduced.TIP
If the engine overheats, see page 8-52 for further
instructions.
EBU23561
To change the coolantWARNING
EWB01890
Wait for the engine and radiator to cool before
removing the radiator cap. You could be
burned by hot fluid and steam blown out under
pressure. Always place a thick rag over the cap
when opening. Allow any remaining pressure
to escape before completely removing the cap.
1. Place the ATV on a level surface.
2. Remove panel F. (See page 8-8.)
3. Place a container under the engine, and then
1. Coolant reservoir cap
2. Maximum level mark
3. Minimum level mark
Coolant reservoir capacity (up to the maximum
level mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
1
2
3

8-23
1
2
3
4
5
6
78
9
10
11

otherwise the cooling system will not be pro-
tected against frost and corrosion.

If water has been added to the coolant, have
a Yamaha dealer check the antifreeze con-
tent of the coolant as soon as possible, oth-
erwise the effectiveness of the coolant will
be reduced.
12. Install the radiator cap, start the engine, let it
idle for several minutes, and then turn it off.
13. Remove the radiator cap to check the coolant
level in the radiator. If it is low, add sufficient
coolant until it reaches the top of the radiator,
and then install the radiator cap.
14. Start the engine, and then check for coolant
leakage.
TIP

If any leakage is found, have a Yamaha dealer
check the cooling system.
15. Install the panel.
EBU26802
Cleaning the air filter element
The air filter element should be cleaned at the in-
tervals specified in the periodic maintenance and
lubrication chart. Clean the air filter element morefrequently if you are riding in unusually wet or dusty
areas.
TIP

There is a check hose at the bottom of the air filter
case. If dust or water collects in this hose, empty
the hose and clean the air filter element and air fil-
ter case.
1. Place the ATV on a level surface.
2. Remove the seat. (See page 4-10.)
3. Remove the air filter case cover by unhooking
the holders.
1. Air filter case check hose
1

8-53
1
2
3
4
5
6
78
9
10
11

Engine overheating
WARNING

EWB02290
Wait for the engine and radiator to cool before removing the radiator cap. You could be burned by
hot fluid and steam blown out under pressure. Always put a thick rag over the cap when opening.
Allow any remaining pressure to escape before completely removing the cap.
TIP

If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the rec-
ommended coolant as soon as possible.
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer check
and repair the cooling system.Add coolant. (See TIP.)
Start the engine. If the engine overheats again, have a
Yamaha dealer check and repair the cooling system.
There is
leakage.
There is
no leakage.

10-2
1
2
3
4
5
6
7
8
910
11

Recommended engine oil grade:
API service SG type or higher, JASO standard MA
Engine oil quantity:
Without oil filter element replacement:
1.40 L (1.48 US qt, 1.23 Imp.qt)
With oil filter element replacement:
1.45 L (1.53 US qt, 1.28 Imp.qt)
Cooling system:
Coolant reservoir capacity (up to the maximum level mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
Radiator capacity (including all routes):
1.25 L (1.32 US qt, 1.10 Imp.qt)
Air filter:
Air filter element:
Wet element
Fuel:
Recommended fuel:
Premium unleaded gasoline only
Fuel tank capacity:
10.0 L (2.64 US gal, 2.20 Imp.gal)
Fuel reserve amount:
3.4 L (0.90 US gal, 0.75 Imp.gal)
Fuel injection:
Throttle body:
Type/quantity:
42EHS/1
Spark plug (s):
Manufacturer/model:
NGK/CR8E
Spark plug gap:
0.7–0.8 mm (0.028–0.031 in)
Clutch:
Clutch type:
Wet, multiple-disc
Transmission:
Primary reduction system:
Spur gear
Primary reduction ratio:
61/23 (2.652)
Secondary reduction system:
Chain drive
Secondary reduction ratio:
38/14 (2.714)
Transmission type:
Constant mesh 5-speed
-20 -10 0
1020 304050 ˚C
SAE 15W-40
SAE 20W-40SAE 20W-50
SAE 10W-40
SAE 5W-30
SAE 10W-30

10-4
1
2
3
4
5
6
7
8
910
11

Operation:
Right hand operation
Recommended fluid:
DOT 4
Rear brake:
Type:
Single disc brake
Operation:
Right foot operation
Recommended fluid:
DOT 4
Front suspension:
Type:
Double wishbone
Spring/shock absorber type:
Coil spring/gas-oil damper
Wheel travel:
250 mm (9.9 in)
Rear suspension:
Type:
Swingarm (link suspension)
Spring/shock absorber type:
Coil spring/gas-oil damper
Wheel travel:
280 mm (11.0 in)
Electrical system:
Ignition system:
TCI (digital)
Charging system:
AC magneto
Battery:
Model:
YTZ-7S
Voltage, capacity:
12 V, 6.0 Ah
Headlight:
Bulb type:
Krypton bulb
Bulb voltage, wattage
×× × ×
quantity:
Headlight:
12 V, 30/30 W
×
2
Tail/brake light:
LED
Neutral indicator light:
LED
Fuel level warning light:
LED
Coolant temperature warning light:
LED
Engine trouble warning light:
LED
Fuses:
Main fuse:
20.0 A

INDEX
A
Accessories and loading ................................................ 6-5
Air filter element, cleaning ............................................ 8-23
B
Battery .......................................................................... 8-43
Brake and clutch levers, checking and lubricating ....... 8-40
Brake fluid, changing.................................................... 8-32
Brake fluid level, checking............................................ 8-30
Brake lever ..................................................................... 4-6
Brake lever free play, checking the front ...................... 8-32
Brake light switches ..................................................... 8-35
Brake pads, checking the front and rear ...................... 8-29
Brake pedal .................................................................... 4-7
Brake pedal, checking and lubricating ......................... 8-41
Brake pedal position, checking .................................... 8-33
Brakes, front and rear .................................................... 5-4
C
Cables, checking and lubricating ................................. 8-40
Chassis fasteners........................................................... 5-8
Cleaning ......................................................................... 9-1
Clutch lever .................................................................... 4-6
Clutch lever free play, adjusting ................................... 8-36
Coolant ................................................................. 5-4
,
8-19
Coolant temperature warning light ................................. 4-2
D
Drive chain ..................................................................... 5-5Drive chain, lubricating ................................................. 8-39
Drive chain slack .......................................................... 8-37
E
Engine break-in .............................................................. 6-4
Engine oil ....................................................................... 5-4
Engine oil and oil filter element .................................... 8-14
Engine, start ................................................................... 6-1
Engine stop switch ......................................................... 4-3
Engine trouble warning light ........................................... 4-3
F
Fuel ........................................................................ 4-9
,
5-4
Fuel level warning light................................................... 4-2
Fuel tank cap.................................................................. 4-8
Fuse, replacing............................................................. 8-46
H
Handlebar position, adjusting ....................................... 4-24
Handlebar switches ........................................................ 4-3
Headlight beam, adjusting............................................ 8-48
Headlight bulb, replacing.............................................. 8-46
I
Identification numbers .................................................. 11-1
Indicator light and warning lights .................................... 4-2
Instruments, lights and switches .................................... 5-8
K
Key identification number ............................................. 11-1