1-3
1
Avoid crossing the side of a steep hill if possible.Always use proper procedures if you stall or roll
backwards when climbing a hill. To avoid stall-
ing, use the proper gear and maintain a steady
speed when climbing a hill. If you stall or roll
backwards, follow the special procedure for
braking described in this manual. Dismount on
the uphill side or to a side if pointed straight up-
hill. Turn the ATV around and remount, following
the procedure described in this manual.Always check for obstacles before operating in a
new area.Never attempt to operate over large obstacles,
such as large rocks or fallen trees. Always follow
proper procedures when operating over obsta-
cles as described in this manual.Always be careful when skidding or sliding.
Learn to safely control skidding or sliding by
practicing at low speeds and on level, smooth
terrain. On extremely slippery surfaces, such as
ice, go slowly and be very cautious in order to re-
duce the chance of skidding or sliding out of con-
trol.Never operate an ATV in fast flowing water or in
water deeper than that recommended in this
manual. Remember that wet brakes may havereduced stopping ability. Test your brakes after
leaving water. If necessary, apply them several
times to let friction dry out the linings.
Always use the size and type of tires specified in
this manual.Always maintain proper tire pressure as de-
scribed in this manual.Never modify an ATV through improper installa-
tion or use of accessories.Never exceed the stated load capacity for an
ATV. Cargo should be properly distributed and
securely attached. Reduce speed and follow in-
structions in this manual for carrying cargo or
pulling a trailer. Allow greater distance for brak-
ing.
WARNING
Always turn off the engine when refueling.Do not refuel right after the engine has been
running and is still very hot.Do not spill gasoline on the engine or ex-
haust pipe/muffler when refueling. Never re-
fuel while smoking, or in the vicinity of
sparks, open flames, or other sources of ig-
nition such as the pilot lights of water heat-
ers and clothes dryers. Gasoline can catch
10-1
10
SPECIFICATIONS
Engine:Engine type: Forced air cooled 4-stroke
Cylinder arrangement: Single cylinder
Displacement: 88 cm (5.37 cu.in)
3
Bore × stroke: 47.0 × 51.0 mm (1.85 x 2.0 in) Compression ratio:
Starting system: Electric starter & kickstarter
Lubrication system: Wet sump 10.2 : 1
Engine oil:Type:SAE10W-40 or SAE20W-50
Recommended engine oil grade: API service SG type or higher, JASO standard MA0 10 30
507090
110130 F
SAE 10W-40
SAE 5W-30
-20
-10 0 102030 40 50 C
SAE 20W-50
Dimensions:Overall length:
1490 mm (58.7 in)
Overall width: 885 mm (34.8 in)
Overall height: 910 mm (35.8 in)
Seat height: 654 mm (25.7 in)
Wheelbase: 1010 mm (39.8 in)
Ground clearance: 100 mm (3.9 in)
Minimum turning radius: 2900 mm (114 in)Weight:With oil and fuel: 120.0 kg (264 lb)
10
Engine oil quantity:Periodic oil change: 0.8 L (0.84 US qt) (0.70 Imp.qt)Final transmission oil:Type:SAE80 API GL-4 Hypoid gear oil
Quantity: 0.30 L (0.32 US qt) (0.27 Imp.qt)Air filter:Air filter element: Wet elementFuel:Recommended fuel: Regular unleaded gasoline only (EUR)
Unleaded gasoline only (AUS)(NZL)
Fuel tank capacity: 4.8 L (1.27 US gal) (1.06 lmp.gal)
Fuel reserve amount: 1.0 L (0.26 US gal) (0.22 Imp.gal)Carburetor:Manufacturer:TK
Type x quantity: SVR 22-1G x 1Spark plug (s):Manufacturer/model:NGK/CR7HSA
Spark plug gap: 0.6–0.7 mm (0.024–0.028 in)
Chassis:Frame type: Steel tube frame
Caster angle: 4.0 °
Trail: 16 mm (0.63 in)
Front tire:Type:Tubeless
Size: AT18 x 7-8
Manufacturer/model: MAXXIS/M939
Clutch:Clutch type: Dry, centrifugal automatic
Transmission:Primary reduction system: V-belt
Primary reduction ratio:
2.47-0.61:1
Secondary reduction system: Spur
Secondary reduction ratio: 41/15 × 45/13 (9.462)
Third reduction system:
Chain drive
Third reduction ratio: 28/13(2.154)
Transmission type: V-belt automatic
10
10-2
