Page 53 of 120
7-7
Do not operate at speeds too fast for your
skills or the conditions.Speed limiters
For riders less experienced with this model, the
throttle lever housing is equipped with a vehicle
speed limiter. This speed limiter keeps the throttle
from fully opening, even when the throttle lever is
pushed to the maximum. Turning in the adjusting
screw limits the maximum engine power available
and decreases the maximum speed of the ATV.
Turning in the adjusting screw decreases top speed,
and turning it out increases top speed.
(See pages 4-3 and 4-4.)
7
This model also has an engine speed limiter plate
to limit the amount of engine power available.
WARNING
Always use the size and type tires specified in
the Owner’s Manual for this ATV on page 5-4.
Always maintain proper tire pressure as de-
scribed in the Owner’s Manual on page 5-5.
Use of improper tires on this ATV, or operation
of this ATV with improper or uneven tire pres-
sure, may cause loss of control, increasingyour risk of an accident.
WARNING
Always go at a speed that is proper for the ter-
rain, visibility and operating conditions, and
your experience. Operating this ATV at speeds
too fast for your skills or the conditions in-
creases your chances of losing control of theATV, which can result in an accident.
Yamaha recommends that all beginning riders start
off with the vehicle speed limiter turned in and the
engine speed limiter plate installed to limit the amount
of speed available while they learn. The vehicle speed
limiter may be gradually adjusted to increase maximum
speed as the beginner becomes more familiar with
operating the ATV. Parents should decide when to
adjust the ATV for more power as their youngster’s
riding skills improve. Once the ATV rider can operate
with skill at the top speed permitted by adjusting the
vehicle speed limiter alone, the engine speed limiter
plate can be removed. Since removal of this plate will
Page 54 of 120
7-8
result in a significant increase in power, turn the vehicle
speed limiter adjusting screw back in again; adjust it
out in stages as you did before. For engine speed
limiter plate removal instructions, see page 4-4.Loading and accessories
Use extra caution when riding the ATV with addi-
tional loads, such as accessories or cargo. The
ATV’s handling may be adversely affected. Re-
duce your speed when adding additional loads.
2. Adjusting screw
MAXIMUM LOADING LIMIT
ATV loading limit (total weight of cargo, rider,
accessories, and tongue):70.0 kg (154 lb)
7
1. Locknut
1
2
WARNING
Never exceed the stated load capacity for
this ATV.Cargo should be properly distributed and se-
curely attached.Reduce speed when carrying cargo or pull-
ing a trailer. Allow greater distance for brak-
ing.Always follow the instructions in your Own-
er’s Manual for carrying cargo or pulling atrailer.
Page 61 of 120
7-15
Do not ride in areas posted “no trespassing”.
Do not ride on private property without getting per-
mission.
Select a large, flat area off-road to become familiar
with your ATV. Make sure that this area is free of
obstacles and other riders. You should practice
control of the throttle, brakes, and turning tech-
niques in this area before trying more difficult ter-
rain. Always avoid riding on paved surfaces: the
ATV is designed for off-road use only, and han-
dling maneuvers are more difficult to perform on
pavement.
Set the parking brake and follow the instruction on
page 6-1 to start the engine. Once it has warmed
up you are ready to begin riding your ATV. Re-
7
member that the engine and exhaust pipe will be
hot when riding and afterwards; do not allow skin
or clothing to come in contact with these compo-
nents.
Apply the throttle slowly and smoothly. You will
start to accelerate. If the throttle is applied too
abruptly, the front wheels may lift off the ground,
resulting in a loss of directional control. Avoid
higher speeds until you are thoroughly familiar
with the operation of your ATV.
When slowing down or stopping, release the throt-
tle and apply the brakes smoothly and evenly. Im-
proper use of the brakes can cause the tires to lose
traction, reducing control and increasing the possi-
bility of an accident.
TURNING YOUR ATV
To achieve maximum traction while riding off-road,
the two rear wheels are mounted solidly on one
axle and turn together at the same speed. There-
fore, unless the wheel on the inside of the turn is al-
lowed to slip or lose some traction, the ATV will
resist turning. A special turning technique must be
used to allow the ATV to make turns quickly and
easily. It is essential that this skill be learned first at With the engine idling, release the parking brake.
Page 66 of 120
7-20
RIDING DOWNHILL
When riding your ATV downhill, shift your weight
as far to the rear and uphill side of the ATV as pos-
sible. Move back on the seat and sit with your arms
straight. Allow the engine compression to do most
of the braking for you. Improper braking may cause
a loss of traction.
Use caution while descending a hill with loose or
slippery surfaces. Braking ability and traction may
be adversely affected by these surfaces. Improper
braking may also cause a loss of traction.
Whenever possible, ride your ATV straight down-
7
WARNING
Maintain a steady speed when climbing a hill.
If you lose all forward speed:Keep weight uphill.Apply the brakes.Lock the parking brake after you are
stopped.
If you begin rolling backwards:Keep weight uphill.Never apply the rear brake while rolling
backwards. Apply the front brake.When fully stopped, apply the rear brake as
well, and then lock the parking brake.
Dismount on uphill side or to a side if pointed
straight uphill. Turn the ATV around and re-
mount, following the procedure described inthe Owner’s Manual.
Page 74 of 120
8-1
PERIODIC MAINTENANCE AND MINOR REPAIR
Safety is an obligation of the owner. Periodic in-
spection, adjustment and lubrication will keep your
ATV in the safest and best operating condition
possible. The most important points of inspection,
adjustment, and lubrication are explained on the
following pages.
The intervals given in the periodic maintenance
and lubrication chart should be considered as a
general guide under normal riding conditions.
However, DEPENDING ON THE WEATHER,
TERRAIN, GEOGRAPHICAL LOCATION, AND
INDIVIDUAL USE, THE MAINTENANCE INTER-
VALS MAY NEED TO BE SHORTENED.
Owner’s manual and tool kit Be sure to put this owner’s manual in the plastic
bag and to always carry it as well as the owner’s
tool kit and the low-pressure tire gauge in their re-
spective compartments under the seat.
8
WARNING
Never service an engine while it is running.
Moving parts can catch clothing or parts of the
body, causing injury. Electrical components
can cause shocks or start fires. Turn off the en-
gine when performing maintenance unlessotherwise specified. Have a Yamaha dealer
perform the service if you are not familiar with
maintenance work.
Page 76 of 120
8-3
Periodic maintenance chart for the emission control system TIPFor ATVs not equipped with an odometer or an hour meter, follow the month maintenance intervals.For ATVs equipped with an odometer or an hour meter, follow the km (mi) or hours maintenance inter-
intervals should be followed.Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools,data and technical skills.NO.ITEM CHECK OR MAINTENANCE
JOB INITIAL
EVERY
Whichev- er comes rst month 1 3 6 6 12
km
(mi) 320
(200) 1300
(800) 2500
(1600) 2500
(1600) 5000
(3200)
hours 20 80 160 160 3201 *Fuel line
Check fuel hoses for cracks or other damage, and
replace if necessary. √ √ √
2 Spark plugCheck condition and clean, regap, or replace if
necessary. √ √ √ √ √
3 *ValvesCheck valve clearance and adjust if necessary.
√√ √ √
4 *CarburetorCheck choke operation and correct if necessary.Check engine idling speed and adjust if neces-
sary. √ √ √ √
5 *
Crankcase breather
systemCheck breather hose for cracks or other damage,
and replace if necessary. √ √ √
8
vals. However, keep in mind that if the ATV isn’t used for a long period of time, the month maintenance
Page 79 of 120
8-6
11
*Shock absorber
assemblies
Check operation and correct if necessary.Check for oil leakage and replace if necessary. √ √ √
12 *
Front knuckle piv-
otsLubricate with lithium-soap-based grease.
√ √ √
13 *Steering shaftLubricate with lithium-soap-based grease.
√ √ √
14 *Steering systemCheck operation and repair or replace if damaged.Check toe-in and adjust if necessary. √ √ √ √ √
Engine oilChange.Check ATV for oil leakage, and correct if neces-
sary. √
√ √ √Change.
NO.ITEM CHECK OR MAINTENANCE
JOB INITIAL
EVERY
Whichev- er comes rst month 1 3 6 6 12
km
(mi) 320
(200) 1300
(800) 2500
(1600) 2500
(1600) 5000
(3200)
hours 20 80 160 160 32017
Check ATV for oil leakage, and correct if neces-
sary. √
√
18 *
Moving parts and
cablesLubricate.
√ √ √ √
8
9
*Wheel hub bearings
Check for looseness or damage, and replace if
necessary. √
√ √ √
10 *Chassis fastenersMake sure that all nuts, bolts, and screws are
properly tightened. √ √ √ √ √
1516
Engine oil strainer Clean.
√√ √
Final transmission oil
Page 82 of 120
8-9
8
Checking the spark plugThe spark plug is an important engine component,
which is easy to check. Since heat and deposits
will cause any spark plug to slowly erode, the spark
plug should be removed and checked in accor-
dance with the periodic maintenance and lubrica-
tion chart. In addition, the condition of the spark
plug can reveal the condition of the engine.
To remove the spark plug1. Remove the spark plug cap.
2. Remove the spark plug as shown, with thespark plug wrench included in the owner’s tool
kit.
1. Spark plug cap
1
