2009 YAMAHA YFM50R fuel

9-2
1
2
3
4
5
6
7
89
10
11

linings.
EBU25932
Storage
Short-term
Always store your ATV in a cool, dry place and, if
necessary, protect it against dust with a porous
cover.
NOTICE

ECB00720

Storing the ATV in a poorly ventilated room
or covering it with a tarp while it is still wet,
will allow water and humidity to seep in and
cause rust.

To prevent corrosion, avoid damp cellars,
stables (because of the presence of ammo-
nia) and areas where strong chemicals are
stored.
Long-term
Before storing your ATV for several months:
1. Follow all the instructions in the “Cleaning”
section of this chapter.
2. Turn the fuel cock lever to “OFF”.
3. Drain the carburetor float chamber by loosen-ing the drain bolt; this will prevent fuel deposits
from building up. Pour the drained fuel into the
fuel tank.
4. Fill up the fuel tank and add fuel stabilizer (if
available) to prevent the fuel from deteriorat-
ing.
5. Perform the following steps to protect the cyl-
inder, piston rings, etc. from corrosion.
a. Remove the spark plug cap and spark
plug.
b. Pour a teaspoonful of engine oil into the
spark plug bore.
c. Install the spark plug cap onto the spark
plug, and then place the spark plug on the
cylinder head so that the electrodes are
grounded. (This will limit sparking during
the next step.)
d. Turn the engine over several times with
the starter. (This will coat the cylinder wall
with oil.)
e. Remove the spark plug cap from the spark
plug, and then install the spark plug and Specified amount:
7.5 ml of stabilizer to each liter of fuel (or 1 oz
of stabilizer to each gallon of fuel)

10-1
1
2
3
4
5
6
7
8
910
11

EBU25960
SPECIFICATIONS
EBU2597B
Dimensions:
Overall length:
1537 mm (60.5 in)
Overall width:
825 mm (32.5 in)
Overall height:
915 mm (36.0 in)
Seat height:
618 mm (24.3 in)
Wheelbase:
1030 mm (40.6 in)
Ground clearance:
75 mm (3.0 in)
Minimum turning radius:
2300 mm (91 in)
Weight:
With oil and fuel:
115.0 kg (254 lb)
Noise and vibration level:
Noise level (77/311/EEC):
76.7 dB(A) (EUR)
Vibration on seat (EN1032, ISO5008):
Will not exceed 0.5 m/s
2

(EUR)
Vibration on handlebar (EN1032, ISO5008):
Will not exceed 2.5 m/s
2

(EUR)
Engine:
Engine type:
Air cooled 4-stroke, SOHC
Cylinder arrangement:
Forward-inclined single cylinder
Displacement:
49.0 cm
3

Bore
×
stroke:
39.0
×
41.4 mm (1.54
×
1.63 in)
Compression ratio:
10.30 :1
Starting system:
Electric starter
Lubrication system:
Wet sump

Engine oil:
Type:
SAE 5W-30 or SAE 10W-30 or SAE 10W-40 or SAE
15W-40 or SAE 20W-40 or SAE 20W-50

10-2
1
2
3
4
5
6
7
8
910
11

Recommended engine oil grade:
API service SG type or higher, JASO standard MA
Engine oil quantity:
Periodic oil change:
0.80 L (0.85 US qt, 0.70 Imp.qt)
Final gear oil:
Type:
SAE 80 API GL-4 Hypoid gear oil
Quantity:
0.12 L (0.13 US qt, 0.11 Imp.qt)
Air filter:
Air filter element:
Wet element
Fuel:
Recommended fuel:
Regular unleaded gasoline only (EUR)
Unleaded gasoline only (AUS)(NZL)
Fuel tank capacity:
6.8 L (1.80 US gal, 1.50 Imp.gal)
Fuel reserve amount:
0.9 L (0.24 US gal, 0.20 Imp.gal)
Carburetor:
Manufacturer:
MIKUNI
Type
×
quantity:
VM16SH x 1
Spark plug (s):
Manufacturer/model:
NGK/CR7HSA
Spark plug gap:
0.6–0.7 mm (0.024–0.028 in)
Clutch:
Clutch type:
Wet, multiple-disc automatic
Transmission:
Primary reduction system:
Spur gear
Primary reduction ratio:
65/20 (3.250)
Secondary reduction system:
Shaft drive
-20 -10 0
1020 304050 ˚C
SAE 15W-40
SAE 20W-40SAE 20W-50
SAE 10W-40
SAE 5W-30
SAE 10W-30

INDEX
A
Accessories and loading ................................................ 6-7
Air filter element, cleaning ............................................ 8-13
B
Battery .................................................................. 5-6
,
8-26
Brake lever free play, adjusting the front...................... 8-21
Brake lever free play (rear), adjusting .......................... 8-23
Brake lever, front ............................................................ 4-6
Brake lever, rear............................................................. 4-6
Brake levers, checking and lubricating......................... 8-25
Brakes, front and rear .................................................... 5-3
Brake shoes, checking the front and rear .................... 8-20
C
Cables, checking and lubricating ................................. 8-24
Carburetor, adjusting.................................................... 8-18
Chassis fasteners........................................................... 5-6
Choke ........................................................................... 4-10
Cleaning ......................................................................... 9-1
D
Drive select lever............................................................ 4-7
E
Engine break-in .............................................................. 6-5
Engine, cold start ........................................................... 6-1
Engine idling speed ...................................................... 8-18
Engine oil ............................................................... 5-3
,
8-9
Engine, starting a warm ................................................. 6-3Engine stop switch ......................................................... 4-2
Engine stop switch with lanyard ..................................... 4-2
F
Final gear oil......................................................... 5-3
,
8-12
Front knuckle pivots, lubricating ................................... 8-25
Fuel ........................................................................ 4-8
,
5-3
Fuel cock ........................................................................ 4-9
Fuel tank cap.................................................................. 4-7
Fuse, replacing............................................................. 8-28
H
Handlebar switches ........................................................ 4-2
I
Identification numbers .................................................. 11-1
Indicator light .................................................................. 4-1
Instruments, lights and switches .................................... 5-6
K
Key identification number ............................................. 11-1
L
Label locations ............................................................... 2-1
M
Main switch .................................................................... 4-1
Maintenance and lubrication chart ................................. 8-5
Maintenance chart, emission control system ................. 8-3
Model label ................................................................... 11-2
N
Neutral indicator light ..................................................... 4-1