2009 YAMAHA XVS950 lights

PERIODIC MAINTENANCE AND ADJUSTMENT
6-5
2
3
4
5
67
8
9

EAU18680
TIP


Air filter

This model’s air filter is equipped with a disposable oil-coated paper element, which must not be cleaned with com-
pressed air to avoid damaging it.

The air filter element needs to be replaced more frequently when riding in unusually wet or dusty areas.

Hydraulic brake service

Regularly check and, if necessary, correct the brake fluid level.

Every two years replace the internal components of the brake master cylinders and calipers, and change the brake
fluid.

Replace the brake hoses every four years and if cracked or damaged.
23

Engine oil filter
cartridge

Replace.
√√√
24

*
Front and rear brake
switches

Check operation.
√√√√√√
25

Moving parts and
cables

Lubricate.
√√√√√
26

*
Throttle grip hous-
ing and cable

Check operation and free play.

Adjust the throttle cable free play
if necessary.

Lubricate the throttle grip housing
and cable.
√√√√√
27

*
Lights, signals and
switches

Check operation.

Adjust headlight beam.
√√√√√√
NO. ITEM CHECK OR MAINTENANCE JOBODOMETER READING
ANNUAL
CHECK 1000 km
(600 mi)10000 km
(6000 mi)20000 km
(12000 mi)30000 km
(18000 mi)40000 km
(24000 mi)

PERIODIC MAINTENANCE AND ADJUSTMENT
6-32
1
2
3
4
5
6
7
8
9
frame in front of the rear wheel or under
each side of the swingarm.

EAU25851
Troubleshooting
Although Yamaha motorcycles receive
a thorough inspection before shipment
from the factory, trouble may occur dur-
ing operation. Any problem in the fuel,
compression, or ignition systems, for
example, can cause poor starting and
loss of power.
The following troubleshooting chart
represents a quick and easy procedure
for checking these vital systems your-
self. However, should your motorcycle
require any repair, take it to a Yamaha
dealer, whose skilled technicians have
the necessary tools, experience, and
know-how to service the motorcycle
properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look like
Yamaha parts, but they are often inferi-
or, have a shorter service life and can
lead to expensive repair bills.
WARNING

EWA15141
When checking the fuel system, do
not smoke, and make sure there are
no open flames or sparks in the ar-
ea, including pilot lights from waterheaters or furnaces. Gasoline or
gasoline vapors can ignite or ex-
plode, causing severe injury or
property damage.

MOTORCYCLE CARE AND STORAGE
7-2
2
3
4
5
6
78
9 off any detergent residue using
plenty of water, as it is harmful
to plastic parts.


Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.

Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.

For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-
pounds for plastic may leavescratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound after
washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea oron salt-sprayed roadsSince sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.
TIP

Salt sprayed on roads in the winter may
remain well into spring.
1. Clean the motorcycle with cold wa-
ter and a mild detergent, after the
engine has cooled down.
NOTICE:
Do not use warm water
since it increases the corrosive
action of the salt.
[ECA10791]

2. After drying the motorcycle, apply
a corrosion protection spray on all
metal, including chrome- and nick-
el-plated, surfaces to prevent cor-
rosion.
After cleaning
1. Dry the motorcycle with a chamois
or an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stain-
less-steel parts, including the ex-
haust system. (Even the thermally
induced discoloring of stain-
less-steel exhaust systems can be
removed through polishing.)
3. To prevent corrosion, it is recom-
mended to apply a corrosion pro-

INDEX
A
Air filter element, replacing ...................... 6-11
Auxiliary light bulb, replacing ................... 6-31
B
Battery ..................................................... 6-24
Brake and clutch levers, checking and
lubricating .............................................. 6-21
Brake and shift pedals, checking and
lubricating .............................................. 6-21
Brake fluid, changing ............................... 6-18
Brake fluid level, checking ....................... 6-17
Brake lever .............................................. 3-10
Brake lever free play, adjusting ............... 6-15
Brake pedal ............................................. 3-10
C
Cables, checking and lubricating ............. 6-20
Care ........................................................... 7-1
Catalytic converter ................................... 3-12
Clutch lever................................................ 3-9
Clutch lever free play, adjusting .............. 6-14
D
Dimmer switch ........................................... 3-8
Drive belt slack ........................................ 6-18
E
Engine break-in ......................................... 5-3
Engine idling speed, checking ................. 6-11
Engine oil and oil filter cartridge ................ 6-7
Engine stop switch..................................... 3-8
Engine trouble warning light ...................... 3-4
F
Front and rear brake pads, checking ....... 6-16
Front fork, checking ................................. 6-23
Fuel.......................................................... 3-11
Fuel consumption, tips for reducing........... 5-3Fuel level warning light .............................. 3-4
Fuel tank cap ........................................... 3-10
Fuses, replacing ...................................... 6-26
H
Handlebar switches ................................... 3-7
Hazard switch ............................................ 3-8
Headlight bulb, replacing ......................... 6-27
Helmet holder .......................................... 3-14
High beam indicator light ........................... 3-3
Horn switch................................................ 3-8
I
Identification numbers ............................... 9-1
Ignition circuit cut-off system ................... 3-16
Immobilizer system.................................... 3-1
Immobilizer system indicator light ............. 3-4
Indicator and warning lights....................... 3-3
K
Key identification number .......................... 9-1
L
License plate light bulb, replacing ........... 6-30
M
Main switch/steering lock .......................... 3-2
Maintenance and lubrication, periodic ....... 6-3
Maintenance, emission control system ..... 6-2
Matte color, caution ................................... 7-1
Model label ................................................ 9-2
Multi-function meter unit ............................ 3-4
N
Neutral indicator light................................. 3-3
O
Oil level warning light ................................ 3-3
P
Panel, removing and installing .................. 6-6Parking ...................................................... 5-4
Part locations ............................................ 2-1
Pass switch ............................................... 3-8
R
Rear brake light switch, adjusting ........... 6-16
Rear suspension, lubricating................... 6-22
RESET switch ........................................... 3-9
Rider seat................................................ 3-13
S
Safety information ..................................... 1-1
SELECT switch ......................................... 3-8
Shifting ...................................................... 5-2
Shift pedal ................................................. 3-9
Shock absorber assembly, adjusting ...... 3-14
Sidestand ................................................ 3-16
Sidestand, checking and lubricating ....... 6-22
Spark plugs, checking ............................... 6-6
Specifications ............................................ 8-1
Starting the engine .................................... 5-1
Start switch ............................................... 3-8
Steering, checking .................................. 6-23
Storage ..................................................... 7-3
Supporting the motorcycle ...................... 6-31
T
Tail/brake light bulb, replacing ................ 6-28
Throttle cable free play, checking ........... 6-12
Throttle grip and cable, checking and
lubricating ............................................. 6-20
Tires ........................................................ 6-12
Tool kit ...................................................... 6-1
Troubleshooting ...................................... 6-32
Troubleshooting chart ............................. 6-33
Turn signal indicator light .......................... 3-3
Turn signal light bulb, replacing .............. 6-29