Ambient temperature display
1. Frost warning indicator “ ”
2. Minus item
3. Temperature
This display shows the ambient tem-
perature from –30 °C (–86 °F) to 50 °C
(122 °F).
The frost warning indicator “ ”
automatically comes on if the tempe-
rature is lower than 3°C (37°F).Oil change indicator “OIL”
1. Oil change indicator “OIL”
The engine oil should be changed
when this indicator comes on. The
indicator stays on until it is reset. After
changing the engine oil, reset the
indicator as follows.
1. While holding the “MODE” and
“SET” buttons pushed, turn the
key to “ON”.
2. Continue holding the “MODE”
and “SET” buttons pushed for
two to five seconds.
3. Release the buttons and the oil
change indicator will go off.
TIP
●The oil change indicator will
come on at the initial 1000 km
(600 mi), 5000 km (3000 mi) after
the initial 1000 km (600 mi) and
every 6000 km (3600 mi) thereaf-
ter.
●If the engine oil is changed befo-
re the oil change indicator comes
on (i.e. before the periodic oil
change interval has been rea-
ched), the indicator must be reset
after the oil change for the next
periodic oil change to be indica-
ted at the correct time. After
resetting, the indicator will come
on for two seconds. If the indica-
tor does not come on, repeat the
procedure.
1
ZAUM0582
INSTRUMENT AND CONTROL FUNCTIONS
3-8
3
1B9-F8199-E3.QXD 21/10/08 13:42 Página 23
1. Oil filter element
2. O-ring
3. Oil filter element cover
7. Check the O-ring for damage and
replace it if necessary.
8. Install the new oil filter element
and an O-ring.
9. Install the oil filter element cover
by installing the bolts, then tigh-
tening them to the specified tor-
que.
TIP
Make sure that the O-ring is properly
seated.
10. Install the washer and the engine
oil drain bolt, and then tighten the
drain bolt to the specified torque.
TIP
Make sure that the washer is properly
seated.
11. Refill with the specified amount
of the recommended engine oil,
and then install and tighten the oil
filler cap.
TIP
Be sure to wipe off spilled oil on any
parts after the engine and exhaust
system have cooled down.
ECA11670
NOTICE
●Do not use oils with a diesel
specification of “CD” or oils of
a higher quality than specified.
In addition, do not use oils
labeled “ENERGY CONSER-
VING II” or higher.
●Be sure no foreign material
enters the crankcase.
12. Start the engine, and then let it
idle for several minutes while
checking it for oil leakage. If oil is
leaking, immediately turn the
engine off and check for the cau-
se.
13. Turn the engine off, and then
check the oil level and correct it if
necessary.
14. Reset the oil change indicator.
(See page 3-6).
Recommended engine oil:
See page 8-1
Oil change quantity:
Without oil filter element
replacement:
1.40 L (1.48 US qt, 1.23 Imp.qt)
With oil filter element
replacement:
1.50 L (1.59 US qt, 1.32 Imp.qt)
Tightening torque:
Engine oil drain bolt:
20 Nm (2.0 m·kgf, 14 ft·lbf)
Tightening torque:
Oil filter cover bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
1
2
3
ZAUM0712
PERIODIC MAINTENANCE AND ADJUSTMENT
6-11
6
1B9-F8199-E3.QXD 21/10/08 13:42 Página 53
