2009 YAMAHA WR 125R high beam

INSTRUMENT AND CONTROL FUNCTIONS
3-2
3To unlock the steering
Push the key in, and then turn it to
“OFF” while still pushing it.
EAU11004
Indicator and warning lights
EAU11020
Turn signal indicator light“”
This indicator light flashes when the
t u r n s i g n a l s w i t c h i s p u s h e d t o t h e l e f t o r
right.
EAU11060
Neutral indicator light“”
This indicator light comes on when the
transmission is in the neutral position.
EAU11080
High beam indicator light“”
This indicator light comes on when the
high beam of the headlight is switched
on.
EAUM2294
Coolant temperature warning
light“”
This warning light comes on if the en-
gine overheats. If this occurs, stop the
engine immediately and allow the en-
gine to cool.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. The warning light should come
on for a few seconds, and then go off.
If the warning light does not come on
initially when the key is turned to “ON”,
or if the warning light remains on, have
a Yamaha dealer check the electrical
circuit.NOTICE
ECA10021
Do not continue to operate the en-gine if it is overheating.
1. Push.
2. Turn.
1. Neutral indicator light“”
2. Turn signal indicator light“”
3. High beam indicator light“”
4. Engine trouble warning light“”
5. Coolant temperature warning light“”
U22BE0E0.book Page 2 Wednesday, December 17, 2008 11:00 AM

INSTRUMENT AND CONTROL FUNCTIONS
3-5
3
EAU12348
Handlebar switches Left
Right
EAU12360
Pass switch “PASS”
Press this switch to flash the headlight.
EAU12400
Dimmer switch“/”
Set this switch to“” for the high
beam and to“” for the low beam.
EAU12460
Turn signal switch“/”
To signal a right-hand turn, push this
switch to“”. To signal a left-hand
turn, push this switch to“”. When re-
leased, the switch returns to the center
position. To cancel the turn signal
lights, push the switch in after it has re-
turned to the center position.
EAU12500
Horn switch“”
Press this switch to sound the horn.
EAU12660
Engine stop switch“/”
Set this switch to“” before starting
the engine. Set this switch to“” to
stop the engine in case of an emergen-
cy, such as when the vehicle overturns
or when the throttle cable is stuck.
EAU12711
Start switch“”
Push this switch to crank the engine
with the starter. See page 5-1 for start-
ing instructions prior to starting the en-
gine.
1. Pass switch “PA S S”
2. Dimmer switch“/”
3. Turn signal switch“/”
4. Horn switch“”
1. Engine stop switch“/”
2. Start switch“”
U22BE0E0.book Page 5 Wednesday, December 17, 2008 11:00 AM

OPERATION AND IMPORTANT RIDING POINTS
5-1
5
EAU15951
Read the Owner’s Manual carefully to
become familiar with all controls. If
there is a control or function you do not
understand, ask your Yamaha dealer.
WARNING
EWA10271
Failure to familiarize yourself with
the controls can lead to loss of con-
trol, which could cause an accidentor injury.
EAU45310
TIPThis model is equipped with a lean an-
gle sensor to stop the engine in case of
a turnover. To start the engine after a
turnover, be sure to turn the main
switch to “OFF” and then to “ON”. Fail-
ing to do so will prevent the engine from
starting even though the engine willcrank when pushing the start switch.
EAUM2322
Starting the engine In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:

The transmission is in the neutral
position.


The transmission is in gear with
the clutch lever pulled and the sid-
estand up.
See page 3-12 for more informa-
tion.
1. Turn the key to “ON” and make
sure that the engine stop switch is
set to“”.
The following warning lights and
indicator light should come on for a
few seconds, then go off.

Neutral indicator light


Turn signal indicator light


High beam indicator light


Coolant temperature warning
light


Engine trouble warning light
U22BE0E0.book Page 1 Wednesday, December 17, 2008 11:00 AM

SPECIFICATIONS
8-3
8
Rear suspension:Type:
Swingarm (monocross)
Spring/shock absorber type:
WR125R Coil spring/gas-oil damper
WR125X Coil spring/oil damper
Wheel travel:
230.0 mm (9.06 in)Electrical system:Ignition system:
TCI (digital)
Charging system:
AC magnetoBattery:Model:
12N5.5-4A
Voltage, capacity:
12 V, 5.5 AhHeadlight:Bulb type:
Halogen bulbBulb voltage, wattage × quantity:Headlight:
12 V, 35 W/35 W × 1
Tail/brake light:
12 V, 21.0 W/5.0 W × 1
Front turn signal light:
12 V, 10.0 W × 2
Rear turn signal light:
12 V, 10.0 W × 2
Auxiliary light:
12 V, 5.0 W × 1
License plate light:
12 V, 5.0 W × 1Meter lighting:
LED
Neutral indicator light:
LED
High beam indicator light:
LED
Turn signal indicator light:
LED
Coolant temperature warning light:
LED
Engine trouble warning light:
LED
Fuses:Main fuse:
20.0 A
Headlight fuse:
15.0 A
Signaling system fuse:
7.5 A
Ignition fuse:
7.5 A
Radiator fan fuse:
5.0 A
U22BE0E0.book Page 3 Wednesday, December 17, 2008 11:00 AM

INDEXAAir filter element and check hose,
replacing and cleaning........................ 6-13
Auxiliary light bulb, replacing ................ 6-31BBattery................................................... 6-27
Brake and clutch levers, checking and
lubricating ........................................... 6-24
Brake fluid, changing ............................ 6-21
Brake fluid level, checking .................... 6-20
Brake lever .............................................. 3-6
Brake pedal ............................................. 3-7
Brake pedal, checking and
lubricating ........................................... 6-25
Brake pedal free play, adjusting............ 6-19CCables, checking and lubricating .......... 6-23
Care ........................................................ 7-1
Catalytic converters ................................ 3-9
Clutch lever ............................................. 3-6
Clutch lever free play, adjusting ............ 6-18
Coolant.................................................. 6-12
Coolant temperature warning light .......... 3-2DDimmer switch ........................................ 3-5
Drive chain, cleaning and lubricating .... 6-23
Drive chain slack ................................... 6-21EEngine break-in ....................................... 5-3
Engine idling speed............................... 6-14
Engine oil and oil filter element ............... 6-9
Engine stop switch .................................. 3-5
Engine trouble warning light.................... 3-3
FFront and rear brake pads, checking .... 6-19
Front brake lever free play, checking ... 6-19
Front fork, checking .............................. 6-26
Fuel......................................................... 3-8
Fuel consumption, tips for reducing........ 5-3
Fuel tank cap .......................................... 3-7
Fuses, replacing ................................... 6-29HHandlebar switches ................................ 3-5
Headlight bulb, replacing ...................... 6-29
High beam indicator light ........................ 3-2
Horn switch ............................................. 3-5IIdentification numbers ............................ 9-1
Ignition circuit cut-off system ................ 3-12
Indicator and warning lights .................... 3-2KKey identification number ....................... 9-1LLicense plate light bulb, replacing ........ 6-31MMain switch/steering lock........................ 3-1
Maintenance and lubrication, periodic .... 6-3
Maintenance, emission control system... 6-2
Model label ............................................. 9-2
Multi-function display .............................. 3-3NNeutral indicator light .............................. 3-2PPanels, removing and installing .............. 6-7
Parking ................................................... 5-4
Part locations .......................................... 2-1
Pass switch............................................. 3-5
SSafety information ................................... 1-1
Seat ....................................................... 3-10
Shifting .................................................... 5-2
Shift pedal ............................................... 3-6
Shock absorber assembly, adjusting .... 3-10
Sidestand .............................................. 3-11
Sidestand, checking and lubricating...... 6-25
Spark plug, checking ............................... 6-8
Specifications .......................................... 8-1
Starting the engine .................................. 5-1
Start switch.............................................. 3-5
Steering, checking................................. 6-26
Storage.................................................... 7-3
Supporting the motorcycle .................... 6-32
Swingarm pivots, lubricating ................. 6-25TTail/brake light bulb, replacing .............. 6-30
Throttle cable free play, adjusting ......... 6-14
Throttle grip and cable, checking and
lubricating ........................................... 6-24
Tires ...................................................... 6-15
Tool kit..................................................... 6-1
Troubleshooting .................................... 6-35
Troubleshooting charts.......................... 6-37
Turn signal indicator light ........................ 3-2
Turn signal light bulb, replacing ............ 6-31
Turn signal switch ................................... 3-5VValve clearance..................................... 6-15
Vehicle identification number .................. 9-1WWheel bearings, checking ..................... 6-27
Wheel (front) ......................................... 6-32
U22BE0E0.book Page 1 Wednesday, December 17, 2008 11:00 AM