2009 YAMAHA WOLVERINE 450 engine coolant

8-29
83. Place a container under the engine, and then
remove the coolant drain bolt. (Use a trough
or a similar object as shown to prevent coolant
from spilling on the footrest.)
4. Remove cowling A. (See page 8-9.)
5. Remove the radiator cap.
1. Coolant drain bolt
1. Trough
1. Radiator cap
U3C263E0.book Page 29 Thursday, May 15, 2008 10:44 AM

8-31
8

If water has been used instead of coolant, re-
place it with coolant as soon as possible,
otherwise the cooling system will not be pro-
tected against frost and corrosion.
If water has been added to the coolant, have
a Yamaha dealer check the antifreeze con-
tent of the coolant as soon as possible, oth-
erwise the effectiveness of the coolant willbe reduced.
13. Install the radiator cap, start the engine, let it
idle for several minutes, and then turn it off.
14. Remove the radiator cap to check the coolant
level in the radiator. If it is low, add sufficient
coolant until it reaches the top of the radiator,
and then install the radiator cap.
15. Start the engine, and then check for coolant
leakage.TIPIf any leakage is found, have a Yamaha dealercheck the cooling system.
16. Install the cowling.
17. Install the panels.
EBU23645Cleaning the air filter element The air filter element should be cleaned at the in-
tervals specified in the periodic maintenance and
lubrication chart. Clean or, if necessary, replace
the air filter element more frequently if you are
riding in unusually wet or dusty areas.TIPThere is a check hose at the bottom of the air filter
case. If dust or water collects in this hose, empty
the hose and clean the air filter element and air fil-ter case.
1. Place the ATV on a level surface.1. Air filter case check hose
U3C263E0.book Page 31 Thursday, May 15, 2008 10:44 AM

8-58
8 Engine overheating
WARNING
EWB02290Wait for the engine and radiator to cool before removing the radiator cap. You could be burned by
hot fluid and steam blown out under pressure. Always put a thick rag over the cap when opening.Allow any remaining pressure to escape before completely removing the cap.TIPIf coolant is not available, tap water can be temporarily used instead, provided that it is changed to the rec-ommended coolant as soon as possible.Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer check
and repair the cooling system.Add coolant. (See TIP.)
Start the engine. If the engine overheats again, have a
Yamaha dealer check and repair the cooling system.
There is
leakage.
There is
no leakage.
U3C263E0.book Page 58 Thursday, May 15, 2008 10:44 AM

10-2
10
Engine oil:Type:
SAE 5W-30 or SAE 10W-30 or SAE 10W-40 or SAE
15W-40 or SAE 20W-40 or SAE 20W-50
Recommended engine oil grade:
API service SG type or higher, JASO standard MA
Engine oil quantity:
Without oil filter cartridge replacement:
2.30 L (2.43 US qt, 2.02 Imp.qt)
With oil filter cartridge replacement:
2.40 L (2.54 US qt, 2.11 Imp.qt)Final gear oil:Type:
SAE 80 API GL-4 Hypoid gear oil
Quantity:
0.23 L (0.24 US qt, 0.20 Imp.qt)
Differential gear oil:Type:
SAE 80 API GL-4 Hypoid gear oil
Quantity:
0.35 L (0.37 US qt, 0.31 Imp.qt)Cooling system:Coolant reservoir capacity (up to the maximum level mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
Radiator capacity (including all routes):
1.32 L (1.40 US qt, 1.16 Imp.qt)Air filter:Air filter element:
Wet elementFuel:Recommended fuel:
Regular unleaded gasoline only
Fuel tank capacity:
14.5 L (3.83 US gal, 3.19 Imp.gal)
Fuel reserve amount:
4.5 L (1.19 US gal, 0.99 Imp.gal)Carburetor:Manufacturer:
MIKUNI
Type × quantity:
BSR33 x 1Spark plug (s):Manufacturer/model:
NGK/DR8EA
Spark plug gap:
0.6–0.7 mm (0.024–0.028 in)
-20 -10 0
1020 304050 ˚C
SAE 15W-40
SAE 20W-40SAE 20W-50
SAE 10W-40
SAE 5W-30
SAE 10W-30
U3C263E0.book Page 2 Thursday, May 15, 2008 10:44 AM

INDEX
AAccessories and loading ................................................ 6-6
Air filter element, cleaning ............................................ 8-31
Axle boots .................................................................... 8-44BBattery .......................................................................... 8-47
Brake fluid, changing .................................................... 8-41
Brake fluid level, checking ............................................ 8-40
Brake lever free play and brake pedal position (rear),
adjusting and checking .............................................. 8-42
Brake lever free play, checking the front ...................... 8-42
Brake lever, front ............................................................ 4-8
Brake levers, checking and lubricating ......................... 8-46
Brake light switches ..................................................... 8-45
Brake pads, checking the front and rear ...................... 8-39
Brake pedal and rear brake lever ................................... 4-8
Brake pedal, checking and lubricating ......................... 8-46
Brakes, front and rear .................................................... 5-4CCables, checking and lubricating ................................. 8-45
Carburetor, adjusting .................................................... 8-36
Chassis fasteners ........................................................... 5-7
Cleaning ......................................................................... 9-1
Coolant .................................................................. 5-3, 8-27
Coolant temperature warning light ................................. 4-2
Cowlings and panels, removing and installing ............... 8-9DDifferential gear oil ......................................................... 5-3Differential gear oil, changing ....................................... 8-25
Drive select lever ............................................................ 4-9
Drive select lever and driving in reverse ........................ 6-3
Drive select lever safety system cable, adjusting ......... 8-39
EEngine break-in .............................................................. 6-5
Engine, cold start ........................................................... 6-1
Engine idling speed ...................................................... 8-36
Engine oil ....................................................................... 5-3
Engine oil and oil filter cartridge ................................... 8-17
Engine, starting a warm ................................................. 6-3
Engine stop switch ......................................................... 4-4FFinal gear oil .......................................................... 5-3, 8-22
Four-wheel-drive indicator .............................................. 4-3
Fuel ......................................................................... 4-9, 5-3
Fuel cock ...................................................................... 4-10
Fuel tank cap .................................................................. 4-9
Fuses, replacing ........................................................... 8-50HHandlebar switches ........................................................ 4-4
Headlight beam, adjusting ............................................ 8-53
Headlight bulb, replacing .............................................. 8-51IIdentification numbers .................................................. 11-1
Indicator lights and warning light .................................... 4-2
Instruments, lights and switches .................................... 5-7
U3C263E0.book Page 1 Thursday, May 15, 2008 10:44 AM