2009 YAMAHA FZ6 NHG drain bolt

DESCRIPTION
2-1
2
EAU10410
Left view1. Main fuse (page 6-30)
2. Fuse box 2 (FZ6-NAHG) (page 6-30)
3. Battery (page 6-29)
4. Air filter element (page 6-14)
5. Idle adjusting screw (page 6-16)
6. Shock absorber assembly spring preload adjusting ring (page 3-21)
7. Owner’s tool kit (page 6-1)
8. Storage compartment (page 3-20)9. Helmet holder (page 3-20)
10.Shift pedal (page 3-14)
11.Engine oil drain bolt (page 6-8)
12.Engine oil filter cartridge (page 6-8)U5S5E2E0.book Page 1 Monday, August 4, 2008 2:07 PM

DESCRIPTION
2-2
2
EAU10420
Right view1. Fuse box 1 (page 6-30)
2. Rear brake fluid reservoir (page 6-21)
3. Engine oil filler cap (page 6-8)
4. Front brake fluid reservoir (page 6-21)
5. Radiator cap (page 6-11)
6. Coolant reservoir (page 6-11)
7. Coolant drain bolt (page 6-12)
8. Engine oil dipstick (page 6-8)9. Brake pedal (page 3-15)
U5S5E2E0.book Page 2 Monday, August 4, 2008 2:07 PM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-9
6
TIPThe engine oil should be between theminimum and maximum level marks.
5. If the engine oil is at or below the
minimum level mark, remove the
oil filler cap, and then add sufficient
oil of the recommended type to
raise it to the correct level.6. Insert and tighten the engine oil
dipstick, and then install and tight-
en the oil filler cap.
To change the engine oil (with or
without oil filter cartridge replace-
ment)
1. Start the engine, warm it up for
several minutes, and then turn it
off.
2. Place an oil pan under the engine
to collect the used oil.
3. Remove the engine oil filler cap
and drain bolt to drain the oil from
the crankcase.
TIPSkip steps 4–6 if the oil filter cartridge isnot being replaced.
4. Remove the oil filter cartridge with
an oil filter wrench.
1. Engine oil dipstick
2. Maximum level mark
3. Minimum level mark
1. Engine oil filler cap
1. Engine oil drain bolt
1. Oil filter cartridge
2. Oil filter wrench
U5S5E2E0.book Page 9 Monday, August 4, 2008 2:07 PM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-10
6
TIPAn oil filter wrench is available at aYamaha dealer.
5. Apply a thin coat of clean engine
oil to the O-ring of the new oil filter
cartridge.TIPMake sure that the O-ring is properlyseated.
6. Install the new oil filter cartridge
with an oil filter wrench, and then
tighten it to the specified torque
with a torque wrench.7. Install the engine oil drain bolt, and
then tighten it to the specified
torque.
TIPCheck the washer for damage and re-place it if necessary.8. Refill with the specified amount of
the recommended engine oil, and
then install and tighten the oil filler
cap.
TIPBe sure to wipe off spilled oil on any
parts after the engine and exhaust sys-tem have cooled down.NOTICE
ECA11620


In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a high-
er quality than specified. In
1. O-ring
1. Torque wrenchTightening torque:
Oil filter cartridge:
17 Nm (1.7 m·kgf, 12 ft·lbf)
Tightening torque:
Engine oil drain bolt:
43 Nm (4.3 m·kgf, 31 ft·lbf)
Recommended engine oil:
See page 8-1.
Oil quantity:
Without oil filter cartridge replace-
ment:
2.50 L (2.64 US qt, 2.20 Imp.qt)
With oil filter cartridge replacement:
2.80 L (2.96 US qt, 2.46 Imp.qt)
U5S5E2E0.book Page 10 Monday, August 4, 2008 2:07 PM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-13
6 5. Remove the coolant reservoir cov-
er and coolant reservoir by remov-
ing the bolts.
6. Drain the coolant from the coolant
reservoir by turning it upside down.7. Install the coolant reservoir and its
reservoir cover by placing them in
the original position, and then in-
stalling the bolts.
8. Remove the coolant drain bolt to
drain the cooling system.
9. After the coolant is completely
drained, thoroughly flush the cool-
ing system with clean tap water.
10. Install the coolant drain bolt, and
then tighten it to the specified
torque.
TIPCheck the washer for damage and re-place it if necessary.11. Pour the specified amount of the
recommended coolant into the ra-
diator and reservoir.
12. Install the coolant reservoir cap.
13. Install the radiator cap, radiator
cap retainer and radiator cap re-
taining bolt.
1. Coolant reservoir cap
2. Coolant reservoir
1. Coolant reservoir cover
2. Bolt
1. Coolant drain bolt
Tightening torque:
Coolant drain bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Antifreeze/water mixture ratio:
1:1
Recommended antifreeze:
High-quality ethylene glycol anti-
freeze containing corrosion inhibitors
for aluminum engines
Coolant quantity:
Radiator capacity (including all
routes):
2.00 L (2.11 US qt, 1.76 Imp.qt)
Coolant reservoir capacity (up to the
maximum level mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
U5S5E2E0.book Page 13 Monday, August 4, 2008 2:07 PM