2009 VOLVO S60 ECU

04 InteriorRear seat and trunk
04102
Folding the rear seat backrest
8503282m
G027327
Backrest release handles in trunkBoth rear seat backrests can be folded down,
together or individually to enable you to trans-
port long objects.
Fold the rear seat backrests as follows:
1. Check first that the head restraint is folded
down.
2. Pull the handle in the cargo compartment
as shown in the illustration.
3. Fold the backrest down.
G028003
WARNING
Keep vehicle doors and the luggage com-
partment locked and keep keys out of a
child's reach. Unsupervised children could
lock themselves in an open trunk and risk
injury. Children should be taught not to play
in vehicles.
On hot days, the temperature in the trunk or
vehicle interior can rise very quickly. Expo-
sure of people to these high temperatures
for even a short period of time can cause
heat-related injury or death. Small children
are particularly at risk.
WARNING
•
When the backrest is returned to the
upright position, check that it is properly
locked in place. Return the head
restraints to the upright position.
•
Long loads should always be securely
anchored to help avoid injury in the
event of a sudden stop.
•
Always turn the engine off and apply the
parking brake when loading/unloading
the vehicle.
•
Place the transmission in the P position
(automatic transmission) to help pre-
vent inadvertent movement of the gear
selector.
•
The vehicle features a 60/40 split fold-
down rear seat. This function is per-
formed by handles inside the trunk, and
also provides a means for children and
adults to enter the passenger compart-
ment in the event they become locked
inside the trunk.
•
Adults are advised to familiarize them-
selves with the operation and location
of the release handles.
•
To fold down the rear seats from inside
the trunk, pull the release control han-
dles located on either side of the trunk.

04 Interior
Rear seat and trunk
04``103 Carrying long loads (ski hatch)
G028068
The center backrest cushion folds forward,
allowing you to transport long, light cargo such
as skis in the trunk of your vehicle. To lower the
backrest:
1. Pull the right release control handle in the
trunk to release the backrest, see
page 102.
2. From the rear seat, fold down the right sec-
tion of the backrest slightly.
3. Release the flap by pushing the catch
(located on the rear side of the backrest)
upward and pulling the flap forward.
4. Return the backrest to the upright position.The cover on the rear seat armrest does not
have hinges and should be removed before the
ski hatch is used.
To remove:
1. Open the cover approximately 30°.
2. Pull it straight up.
To put in place:
1. Press the cover into the groove behind the
upholstery.
2. Close the cover.
Grocery bag holder (option)
G027223
Open the trunk lid. Hang or secure your grocery
bags§ using the tensioning straps or holders.
Center head restraints
G028074
Adjust the head restraint verticallyThe center head restraint can be adjusted
according to the passenger's height. The
restraint should be carefully adjusted to sup-
port the occupant's head.
The head restraint can be raised by pulling
straight up or lowered by pressing the catch at
the base of the left head restraint support and
pushing down.

04 Interior
Spare wheel, tools and jack
04
*Option/accessory, for more information, see Introduction.
105
G027201
Spare wheel* Securing bracket Tool bag* with towing eyelet Jack*
The spare wheel, jack and tool bag are located
under the floor of the trunk. To access the
spare tire:
1. Pull up the floor mats.
2. Remove the jack and tool bag.
3. Unscrew the spare wheel and lift it out.
WARNING
Make sure that the spare tire, jack and tool
bag are properly secured with the securing
bracket to help keep these components in
place in the event of a sudden stop.If the vehicle is equipped with a grocery bag
holder:
1. Turn the two clips, which are located at the
rear corner of the mat, 90°.
2. Pull the front of the floor mat back towards
the trunk lid opening.
3. Lift the mat slightly and turn 90° to lift it out.
4. Lift the mat out of the trunk.
5. Unscrew the spare tire and lift it out.
6. Return and secure everything in reverse
order.
See page 170 for more information on using
the jack.

06 Starting and drivingTowing
06140
Emergency towing
ABC
G028091
Front towing eyeletThe towing eyelet is located in the tool bag,
under the floor of the trunk, with the spare tire.
This eyelet must be screwed into the positions
provided on the right sides of either the front or
rear bumper (B, see illustrations).
WARNING
Do not use the towing eyelets to pull the
vehicle up onto a flat bed tow truck.
To attach the towing eyelet:A. Use a coin to pry open the lower edge of
the cover (A)
1.
B. Screw the towing eyelet (C) in place, first
by hand and then using the tire iron until it
is securely in place.
After the vehicle has been towed, the eyelet
should be removed and returned to the tool
bag. Press the cover back into position.A
B
C
G028093
Rear towing eyelet
Precautions when the vehicle is in tow•
The steering wheel must be unlocked. Turn
the ignition key to position I or II.
•
The gear selector must be in position N.
•
Maximum speed: 50 mph (80 km/h). Do not
exceed the maximum allowable towing
speed.
•
Maximum distance with front wheels on
ground: 50 miles (80 km).
•
While the vehicle is being towed, try to
keep the tow rope taut at all times.
•
The vehicle should only be towed in for-
ward direction.
1The opening in the cover may vary.

06 Starting and driving
Towing
06
141
CAUTION
•
Please check with state and local
authorities before attempting this type
of towing, as vehicles being towed are
subject to regulations regarding maxi-
mum towing speed, length and type of
towing device, lighting, etc.
•
If the vehicle's battery is dead, do not
attempt to start the vehicle by pushing
or pulling it as this will damage the
three-way catalytic converter(s). The
engine must be jump started using an
auxiliary battery (see page 142).
•
If the vehicle is being towed on a flat bed
truck, the towing eyelets must not be
used to secure the vehicle on the flat
bed. Consult the tow truck operator.
WARNING
•
Remember that the power brakes and
power steering will not function when
engine is not running. The braking and
steering systems will function but the
brake pedal pressure required is
3 – 4 times above normal and greater
steering effort must be exerted.
•
The towing eyelets must not be used for
pulling another vehicle out of a ditch or
for any similar purpose involving severe
strain.
•
Do not use the towing eyelets to pull the
vehicle up onto a flat bed tow truck.
Towing vehicles with front wheel drive/
All Wheel DriveVolvo recommends the use of flat bed equip-
ment.
If wheel lift equipment must be used, please
use extreme caution to help avoid damage to
the vehicle. In this case, the vehicle should
be towed with the rear wheels on the ground
if at all possible.
If it is absolutely necessary to tow the vehicle
with the front wheels on the ground, please
refer to the towing information on the previous
page.
CAUTION
•
Sling-type equipment applied at the
front will damage radiator and air con-
ditioning lines.
•
It is equally important not to use sling-
type equipment at the rear or apply lift-
ing equipment inside the rear wheels;
serious damage to the rear axle may
result.
•
If the vehicle is being towed on a flat bed
truck, the towing eyelets must not be
used to secure the vehicle on the flat
bed. Consult the tow truck operator.WARNING
Do not use the towing eyelets to pull the
vehicle up onto a flat bed tow truck.

06 Starting and drivingLoad carriers (accessory)
06146
G027340
Load carrierLoad carriers are available as Volvo accesso-
ries. Observe the following points when in use:•
To avoid damaging your vehicle and to
achieve maximum safety when driving, we
recommend using the load carriers that
Volvo has developed especially for your
vehicle.
•
Volvo-approved removable roof racks are
designed to carry the maximum allowable
roof load for this vehicle: 220 lbs (100 kg).
For Non-Volvo roof racks, check the man-
ufacturer's weight limits for the rack.
•
Never exceed the rack manufacturer's
weigh limits and never exceed the maxi-
mum rated roof load of 220 lbs (100 kg).
•
Avoid single-point loads. Distribute loads
evenly.
•
Place heavier cargo at the bottom of the
load.
•
Secure the cargo correctly with appropri-
ate tie-down equipment.
•
Check periodically that the load carriers
and load are properly secured.
•
Remember that the vehicle's center of
gravity and handling change when you
carry a load on the roof.
•
The vehicle's wind resistance and fuel con-
sumption will increase with the size of the
load.
•
Drive smoothly. Avoid rapid starts, fast
cornering and hard braking.
Attaching load carriers
G027347
The attachment brackets for the load carriers
are located under the roof molding.
1. Make sure that the load carriers are placed
in the right direction. See the mark on the
decal under the cover.
2. Press the guide lugs into the holes (1).
3. Carefully lower the opposite side of the
load carrier to the roof.
4. Loosen the tightening wheel slightly. Slide
the hook on the load carrier attachment
into the attachment bracket under the roof
molding.

06 Starting and driving
Load carriers (accessory)
06
147
5. Turn the tightening wheel to secure the
load carrier in the attachment bracket.
6. Repeat this procedure for the other load
carrier attachments.
7. Check that the hooks on all four load carrier
attachments are securely tightened in the
respective attachment brackets on the roof
of the vehicle.
8. Press down the covers.
Check periodically that the load carriers and
load are properly secured.

07 Wheels and tires
Changing wheels
07``169
G020331
Insert flat end of lug wrench and turn/pull straight
outThe spare wheel is located under the carpet on
the trunk floor. The jack and crank are secured
in the wheel recess.
There are two jack attachment points on each
side of the vehicle (see illustration below).To change a wheel:1. Engage the parking brake.
2.
Put the gear selector in P (automatic trans-
mission) or reverse (manual transmission).
G020332
Loosen the wheel bolts3. Remove the wheel cap (where applicable)
using the lug wrench in the tool bag.
4. With the vehicle still on the ground, use the
lug wrench to loosen the wheel bolts 1/2 -
1 turn by exerting downward pressure.
Turn the bolts counterclockwise to loosen.
CAUTION
•
The vehicle must not be driven with
wheels of different dimensions or with a
spare tire other than the one that came
with the vehicle. The use of different size
wheels can seriously damage your vehi-
cle's transmission.
•
Correct tightening torque on wheel
bolts must be observed. The wheel
bolts should never be greased or lubri-
cated. The extended, chromed wheel
bolts must not be used with steel rims,
as they make it impossible to fit the hub
caps.
•
Locking wheel bolts can be used on
both aluminum and steel wheels. If hub
caps are used on steel wheels, the lock-
ing wheel bolt should be mounted in the
hole as far from the tire's inflation valve
as possible. It would otherwise not be
possible to mount the hub cap on the
wheel.