2009 VOLVO S60 ECO mode

07 Wheels and tires
Tire inflation pressure table - Canadian models
07
159
The following tire pressures are recommended
by Volvo for your vehicle. Refer to the tire infla-tion placard for information specific to the tires
installed on your vehicle at the factory.Tire size
Cold tire pressures up to five persons psi (kPa)
Optional pressure up to three persons psi (kPa)
Front
Rear
Front
Rear
195/65R15
205/55R16
215/55R16
235/45R17
38 (260)
38 (260)
32 (220)
32 (220)
235/40R18
39 (270)
39 (270)
35 (240)
35 (240)
Temporary spare tire
T125/80R17
61 (420)
61 (420)
61 (420)
61 (420)

07 Wheels and tiresGlossary of tire terminology
07162
Tire suppliers may have additional markings,
notes or warnings such as standard load, radial
tubeless, etc.•
Tire information placard: A placard
showing the OE (Original Equipment) tire
sizes, recommended inflation pressure,
and the maximum weight the vehicle can
carry.
•
Tire Identification Number (TIN): A num-
ber on the sidewall of each tire providing
information about the tire brand and man-
ufacturing plant, tire size and date of man-
ufacturer.
•
Inflation pressure: A measure of the
amount of air in a tire.
•
Standard load: A class of P-metric or Met-
ric tires designed to carry a maximum load
at 35 psi [37 psi (2.5 bar) for Metric tires].
Increasing the inflation pressure beyond
this pressure will not increase the tires load
carrying capability.
•
Extra load: A class of P-metric or Metric
tires designed to carry a heavier maximum
load at 41 psi [43 psi (2.9 bar) for Metric
tires]. Increasing the inflation pressure
beyond this pressure will not increase the
tires load carrying capability.
•
kPa: Kilopascal, a metric unit of air pres-
sure.
•
PSI: Pounds per square inch, a standard
unit of air pressure.
•
B-pillar: The structural member at the side
of the vehicle behind the front door.
•
Bead area of the tire: Area of the tire next
to the rim.
•
Sidewall of the tire: Area between the
bead area and the tread.
•
Tread area of the tire: Area of the perim-
eter of the tire that contacts the road when
mounted on the vehicle.
•
Rim: The metal support (wheel) for a tire or
a tire and tube assembly upon which the
tire beads are seated.
•
Maximum load rating: a figure indicating
the maximum load in pounds and kilo-
grams that can be carried by the tire. This
rating is established by the tire manufac-
turer.
•
Maximum permissible inflation pres-
sure: the greatest amount of air pressure
that should ever be put in the tire. This limit
is set by the tire manufacturer.
•
Recommended tire inflation pressure:
inflation pressure, established by Volvo,
which is based on the type of tires that are
mounted on a vehicle at the factory. This
inflation pressure is affected by the number
of occupants in the vehicle, the amount of
cargo, and the speed at which the vehicle
will be driven for a prolonged period. Thisinformation can be found on the tire infla-
tion placard(s) located on the driver's side
B-pillar or on the inside of the fuel filler door
on Canadian models, and in the tire infla-
tion table in this chapter.
•
Cold tires: The tires are considered to be
cold when they have the same temperature
as the surrounding (ambient) air. This tem-
perature is normally reached after the vehi-
cle has been parked for at least 3 hours.

07 Wheels and tiresTire Pressure Monitoring System (TPMS) - U.S. models
07172
The tire pressure monitoring system uses sen-
sors mounted in the tire valves to check infla-
tion pressure levels. When the vehicle is
moving at a speed of approximately 20 mph
(30 km/h) or faster, these sensors transmit
inflation pressure data to a receiver located in
the vehicle.USA - FCC ID: MRXG403MA4
A
This device complies with part 15 of the FCC
rules. Operation is subject to the following
conditions: (1) This device may not cause
harmful interference, and (2) this device
must accept any interference received,
including interference that may cause unde-
sired operation.AOn certain models, the FCC code is MRXTG315AM04When low inflation pressure is detected, TPMS
will light up the tire pressure warning light (also
referred to as a telltale) in the instrument panel,
and will display a message in the text window.
The wording of this message is determined by
the degree of inflation pressure loss.
NOTE
If a fault occurs in TPMS, the tire pressure
warning light will flash for approximately
1 minute and
TIRE PRESS SYST
SERVICE REQUIRED
will be displayed.
Each tire, including the spare (if provided),
should be checked monthly when cold and
inflated to the inflation pressure recommended
by the vehicle manufacturer on the vehicle
placard or tire inflation pressure label. (If your
vehicle has tires of a different size than the size
indicated on the vehicle placard or tire inflation
pressure label, you should determine the
proper tire inflation pressure for those tires.)
As an added safety feature, your vehicle has
been equipped with a tire pressure monitoring
system (TPMS) that illuminates a low tire pres-
sure telltale when one or more of your tires is
significantly under-inflated. Accordingly, when
the low tire pressure telltale illuminates, you
should stop and check your tires as soon as
possible, and inflate them to the proper pres-
sure. Driving on a significantly under-inflated
tire causes the tire to overheat and can lead to
tire failure. Under-inflation also reduces fuel
efficiency and tire tread life, and may affect the
vehicle's handling and stopping ability.
Please note that the TPMS is not a substitute
for proper tire maintenance, and it is the driv-er's responsibility to maintain correct tire pres-
sure, even if under-inflation has not reached
the level to trigger illumination of the TPMS low
tire pressure telltale.
Your vehicle has also been equipped with a
TPMS malfunction indicator to indicate when
the system is not operating properly. The
TPMS malfunction indicator is combined with
the low tire pressure telltale. When the system
detects a malfunction, the telltale will flash for
approximately one minute and then remain
continuously illuminated. This sequence will
continue upon subsequent vehicle start-ups as
long as the malfunction exists. When the mal-
function indicator is illuminated, the system
may not be able to detect or signal low tire
pressure as intended. TPMS malfunctions may
occur for a variety of reasons, including the
installation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS
from functioning properly. Always check the
TPMS malfunction telltale after replacing one
or more tires or wheels on your vehicle to
ensure that the replacement or alternate tires
and wheels allow the TPMS to continue to
function properly.

07 Wheels and tires
Tire Pressure Monitoring System (TPMS) - U.S. models
07
173
NOTE
TPMS indicates low tire pressure but does
not replace normal tire maintenance. For
information on correct tire pressure, please
refer to the tables on pages 158 and 159, or
consult your Volvo retailer.Erasing warning messagesWhen a low tire pressure warning message has
been displayed, and the tire pressure warning
light has come on:•
Use a tire pressure gauge to check the
inflation pressure of all four tires.
•
Re-inflate the tire(s) to the correct pressure
(consult the tire pressure placard or the
tables on pages 158 and 159).
•
Drive the vehicle for several minutes at a
speed of 20 mph (30 km/h) or faster.
This will erase the warning text and the warning
light will go out.WARNING
Incorrect inflation pressure could lead to tire
failure, resulting in a loss of control of the
vehicle.
Changing wheels with TPMSPlease note the following when changing or
replacing the factory installed TPMS wheels/
tires on the vehicle:•
Only the factory-mounted wheels are
equipped with TPMS sensors in the valves.
•
If the vehicle is equipped with a temporary
spare tire, this tire does not have a TPMS
sensor.
•
If wheels without TPMS sensors are moun-
ted on the vehicle,
TIRE PRESS SYST
SERVICE REQUIRED
will be displayed
each time the vehicle is driven above
25 mph (40 km/h) for 10 minutes or more.
•
Once TPMS sensors are properly installed,
the warning message should not reappear.
•
Volvo recommends that TPMS sensors be
fitted on all wheels used on the vehicle.
Volvo does not recommend moving sen-
sors back and forth between sets of
wheels.NOTE
If a tire is changed or if the TPMS sensor is
moved to another wheel, the sensor’s seal,
nut and valve core should be replaced.
CAUTION
When inflating tires with TPMS valves, press
the pump's mouthpiece straight onto the
valve to help avoid bending or otherwise
damaging the valve.

09 Maintenance and servicing
Engine oil
09
191
NOTE
Volvo uses different systems to indicate a
low oil level or pressure. Some models have
an oil pressure sensor, in which case a
warning symbol (see page 52) is used to
indicate low oil pressure. Other models have
an oil level sensor, in which case the driver
is alerted by the warning symbol in the cen-
ter of the instrument panel and a text in the
information display. Some models use both
systems. Contact a trained and qualified
Volvo service technician for more informa-
tion.Changing engine oil and oil filterSee the information on oil specifications above
and page 240 for oil volumes. Refer to the
Warranty and Service Records Information
booklet for information on the oil change inter-
vals.
NOTE
•
Volvo does not recommend the use of
oil additives.
•
Synthetic oil is not used when the oil is
changed at the normal maintenance
intervals except at owner request and at
additional charge. Please consult a
trained and qualified Volvo service tech-
nician.
Checking and adding oilThe oil level should be checked every time the
vehicle is refueled. This is especially important
during the period up to the first scheduled
maintenance service.•
The vehicle should be parked on a level
surface when the oil is checked.
•
If the engine is warm, wait for at least
10-15 minutes after the engine has been
switched off before checking the oil.
Checking the oil
G020336
1. Pull out the dipstick and wipe it with a lint-
free rag.2. Reinsert the dipstick, pull it out, and check
the oil level.
3. Add oil if necessary. If the level is close to
theMINmark, add approximately
1 US quart (1 liter) of oil.
4. Run the engine until it reaches normal
operating temperature.
5. Switch off the engine and wait for at least
10-15 minutes and recheck the oil level. If
necessary, add oil until the level is near the
MAX mark.
CAUTION
•
Not checking the oil level regularly can
result in serious engine damage if the oil
level becomes too low.
•
Never fill oil above the MAX mark. This
could cause an increase in oil consump-
tion.
•
Not checking the oil level regularly can
result in serious engine damage if the oil
level becomes too low.
•
Always add oil of the same type and
viscosity as already used.WARNING
Do not allow oil to spill onto or come into
contact with hot exhaust pipe surfaces.

09 Maintenance and servicing
Replacing bulbs
09``199
Low beam headlight/parking light (halogen
headlights)High beam headlight, parking light (Active
Bi-Xenon headlights)
Certain models may have a plastic tube that
may hinder access to the bulbs. This tube can
be broken off and discarded.NOTE
If you encounter difficulty when changing a
bulb, please contact a trained and qualified
Volvo service technician.Low beam headlight
G028435
Low beam bulb (halogen headlights)
Removing the defective bulb:1. Switch off the headlights and turn the igni-
tion switch to position 0.
2. Remove the plastic cover.
3. Disconnect the wiring connector.
Loosen the retaining spring by first moving
it to the right and then moving it outward
and downward, out of the way.
Pull out the defective bulb.
G028436
Installing the new bulb:
Insert the new bulb, without touching the
glass, with the guide lug upward. The bulb
will only seat properly in this position.
Move the retaining spring up and push it
slightly to the left until it seats properly.
1. Reconnect the wiring connector.
2. Reinstall the plastic cover.
NOTE
If the vertical aim of your headlights needs
to be adjusted for any reason (e.g., towing
a trailer for extended periods), this should
be done by a trained and qualified Volvo
service technician.High beam headlight
G028437
High beam bulb

10 Audio
Radio functions HU-650/HU-850
10``221 Selecting a sound source
The sound source (e.g. AM,
FM, etc.) can be selected in two
ways:
•
Use the sound source buttons (see the
center illustration above).
•
Turn the SOURCE knob (see illustration) to
select a sound source (AM1, AM2, FM1,
FM2, FM3, or CD). Press the knob to select
theAM or FMband of your choice.
The sound source selected will be shown in the
display.
Scan
Press the SCAN button to start
the station scan function. When
a station is found, scanning
stops for approximately 10 sec-
onds, after which scanning will
continue.
Press the SCAN or SOURCE button when a
station has been found if you would like to lis-
ten to that station and to discontinue the scan
function.
Station seek up/downPress
or
to start the seek func-
tion. The radio seeks the next audible station
and tunes it in. Repeat the procedure to con-
tinue the seek function.
Manual station searchPress
or
and hold it down.
MAN will be shown in the display. The radio
scans slowly in the selected direction and will
increase the scanning speed after a few sec-
onds. Release the button when the desired
frequency appears in the display.
The frequency can be fine-tuned by short
presses on the or
keys.
The system will remain in manual search mode
for 5 seconds after the button is released, after
which it will return to seek mode.
Steering wheel key pad (option)
G027901
If the vehicle is equipped with the key pad in
the steering wheel press the right or left arrow
to switch between preset stations.

10 AudioRadio functions HU-650/HU-850
10222
Storing stations
G027191
To store a selected station under one of the
station setting buttons 1-6:
1. Tune to the desired station.
2. Press the button under which the station is
to be stored and keep it depressed. The
audio system sound will be interrupted for
a few seconds and
STORED
will appear in
the display. The station is now stored.
A total of 30 stations can be stored; 6 stations
each in AM1, AM2, FM1, FM2, andFM3.
Storing stations automatically
This function automatically
searches for and stores up to
10 strong AM or FM stations in
a separate memory. If more
than ten stations are found, the
ten strongest ones are stored.
This function is especially useful in areas in
which you are not familiar with radio stations or
their frequencies.
To use the AUTO function:
1.
Select radio mode using the AM or FM
buttons, or by turning the SOURCE knob.
2.
Start the search by pressing AUTO for
more than 2 seconds.
3.
AUTO
appears in the display and a number
of stations with strong signals (max. 10)
from the selected frequency band will be
stored in the auto-store memory. If there
are no stations with sufficient signal
strength,
NO STATION
is displayed.
4.
Press the AUTO button or the arrow keys
on the optional steering wheel controls
briefly to select the stored stations.
When the radio is in auto-store mode,
AUTO
is
shown in the display.
AUTO
disappears when
you return to the normal radio mode.Return to the normal radio mode by pressing
theAM, FM, or EXIT button.
To return to the Auto-store mode, press the
AUTO button briefly.