2009 VOLVO S60 turn signal

05 Locks and alarmAlarm
05116
Visual alarm signalThe visual alarm signal is given by flashing all
turn signals and turning on the interior lighting
for approximately 5 minutes.Audible alarm signalAn audible alarm signal is given by a battery
powered siren. One alarm cycle lasts for
25 seconds."Panic" buttonIn an emergency situation, this feature can be
used to attract attention.
Activate the "panic" button by pressing the red
button on the remote control (see the illustra-
tion on page 109) for at least 3 seconds or by
pressing this button twice within 3 seconds.
The turn signals will flash, and the vehicle's
horn will sound.
The function can be turned off by pressing any
of the buttons on the remote control or will stop
automatically after 25 seconds. When a button
is pressed, there is a 5 second delay before the
panic alarm is deactivated.
NOTE
This button will NOT unlock the vehicle.
Temporarily turning off the inclination
and movement alarm sensor(s) -
accessory
G027228
This button will only be found in vehicles equip-
ped with the accessory inclination and/or
movement sensors. The position of this button
may vary, depending on the specifications of
your vehicle.
FCC ID: MAYDA5823
This device complies with part 15 of the FCC
rules. Operation is subject to the following
conditions: (1) This device may not cause
harmful interference, and (2) this device
must accept any interference received,
including interference that may cause unde-
sired operation.
Canadian IC: 4405A-DA5823
Movement sensor DA5823 by Dynex
Operation is subject to the following condi-
tions: (1) this device may not cause interfer-
ence, and (2) this device must accept any
interference, including interference that may
cause undesired operation of the device.In certain situations it may be desirable to turn
off the accessory inclination and movement
alarm sensors if, for example, you drive your
vehicle onto a ferry where the rocking of the
boat could trigger the alarm or if a pet is left in
the vehicle with the doors locked.
To temporarily turn off the inclination and
movement alarm sensors from the alarm
system:
From the time the ignition key is turned from
the Drive position (position II) until you lock the
vehicle, you can press the button in the center

05 Locks and alarm
Alarm
05
117
console. The LED in the switch will light up and
a message will be displayed in the text window
to indicate that the sensors are disconnected.
The vehicle can then be locked in the usual way
to set the alarm.
NOTE
•
This function will not turn off the vehi-
cle's standard alarm.
•
The optional sensors are automatically
reconnected to the alarm system the
next time the vehicle is unlocked and
then locked again.
LED alarm status signalsThe status of the alarm system is indicated by
the red LED at the top of the dash:•
LED off - the alarm is not armed
•
LED flashes once per second - the alarm is
armed
•
LED flashes rapidly before the ignition is
switched on - the alarm has been triggered
•
Fault in the alarm system: If a fault has
been detected in the alarm system, a mes-
sage will be displayed in the text window.
Contact a trained and qualified Volvo serv-
ice technician.
Automatic re-lock/re-arm systemIf the vehicle is unlocked with the remote, the
vehicle will re-lock and the alarm will re-arm
after 2 minutes unless a door or the trunk has
been opened.

09 Maintenance and servicingReplacing bulbs
09198
When replacing bulbs, keep the following
points in mind:•
Never touch the glass of bulbs with your
fingers. Grease and oils from your fingers
vaporize in the heat and will leave a deposit
on the reflector, which will damage it.
•
The optional Active Bi-Xenon headlight
bulbs contain trace amounts of mercury.
These bulbs should always be disposed of
by an authorized Volvo retailer.
The following bulbs should only be replaced by
an authorized Volvo service technician:
•
Active Bi-Xenon headlights,
•
Courtesy (dome) lighting,
•
Reading lights,
•
Glove compartment lights
•
Turn signals and courtesy lights in the side
door mirrors
•
High-mounted brake lights
•
Diodes in the rear tail lightsNOTE
For information regarding any other bulbs
not mentioned in this section, please con-
tact your Volvo retailer or a trained and
authorized Volvo service technician.
Replacing bulbs at the front of the
vehicle
WARNING
•
The engine should not be running when
changing bulbs.
•
When changing in the headlight hous-
ing, if the engine has been running just
prior to replacing bulbs, please be
aware that components in the engine
compartment will be hot.
G027278
All front bulbs (except the optional front fog
lights) are replaced from the engine compart-
ment.
WARNING
Active Bi-Xenon headlights (option) - due to
the high voltage used by these headlights,
these bulbs should only be replaced by a
trained and qualified Volvo service techni-
cian.Location of the bulbs in the headlight
housing
G028433
Side marker lightTurn signal

09 Maintenance and servicing
Replacing bulbs
09``201 Turn signal, driver's side
G028438
Removing the defective bulb:1. Switch off the headlights and turn the igni-
tion switch to position 0.
2. Pull out the bulb holder by twisting it coun-
terclockwise.
3. Remove the bulb from the holder by press-
ing it in and turning it counterclockwise.Installing the new bulb:1. Insert the new bulb into the holder by
pressing it in and turning it clockwise.
2. Reinsert the bulb holder in the headlight
housing and twist it clockwise until it seats
properly.
Turn signal, passenger's side
G027283
1. Switch off the headlights and turn the igni-
tion switch to position 0.
2. Remove radiator pipe (1) from the box.
3. Remove filler pipe screw (2).
4. Pull the filler pipe (3) straight up.
5. Remove vent hose (4) from filler pipe.Installing the new bulb:1. Replace the bulb (same procedure as the
driver's side bulb).
2. Ensure that the seal between the washer
fluid reservoir and the filler pipe is correctly
positioned.3. Press the filler pipe (3) back into position.
4. Press the vent hose (4) into place on the
filler pipe.
5. Reinstall and tighten the filler pipe screw
(2).
6. Reinstall the radiator pipe to the box (1).
Side marker light
G028439
Side marker light1. Turn the lamp holder counterclockwise
and pull it out.
2. Pull out the defective bulb and insert a new
one.

09 Maintenance and servicing
Replacing bulbs
09``203 Replacing bulbs in the taillight cluster
3501204m
G027277
Location of bulbs
Brake lightParking light (left side)Fog light (one side)Side marker lampTurn signalBack up light
All bulbs in the taillight cluster can be replaced
from inside the trunk.1. Switch off all lights and turn ignition key to
position0.
2. Unlock and fold down the side panel to
access the bulbs.
The bulbs are located in two separate bulb
holders, an upper and a lower. Each bulb
holder has a locking pin.
Replace bulbs in the upper and lower
bulb holders as follows:1. To ease the work: disconnect the cable
from the bulb holder.2. Press the catches together and pull out the
holder.
3. Replace the bulb.
4. Reconnect the cable.
5. Close and secure the side panel.
NOTE
If the message indicating a burned out bulb
remains in the information display after the
bulb has been replaced, consult a trained
and qualified Volvo service technician.

09 Maintenance and servicing
Fuses
09
213
No.
A
17
Accessory audio
5
18
–
19
Folding head restraints
15
20
Trailer wiring (15-feed) - option
20
21
–
22
–
23
All Wheel Drive
7.5
24
Four-C chassis system
(option)
15
25
–
26
Park assist (option)
5
27
Main fuse: trailer wiring, Four-
C, park assist, All Wheel Drive
30
28
Central locking system
15
29
Driver's side trailer lighting:
parking lights, turn signal
(option)
25
30
Passenger's side trailer light-
ing: parking light, brake light,
fog light, turn signal (option)
25
No.
A
31
Main fuse: fuses 37 and 38
40
32
–
33
–
34
–
35
–
36
–
37
Heated rear window
20
38
Heated rear window
20

10 AudioRadio functions HU-650/HU-850
10220
The volume level for the auxiliary device can
now be adjusted.
Press EXIT to save the setting and exit the
menu.Sound settings
G027191
Optimal sound reproductionThe audio system is calibrated for optimal
sound reproduction through the use of digital
signal processing. This calibration takes into
account the speakers, amplifier, cabin acous-
tics, the seating position of the listener, etc., for
each combination of vehicle and audio system.
There is also dynamic calibration that takes
into account the setting of the volume control,radio reception, and the vehicle's speed. The
sound settings described in this manual, such
as
BASS
,TREBLE
, and
EQUALIZER
are only
intended to enable the user to adapt sound
reproduction to his/her personal preferences.
Bass
Adjust the bass by pressing the button to
extend the control and turning it to the left (less
bass) or to the right (more bass). A "detent"
indicates "equalized" bass. Press the button
back in when you have made the adjustment.
Treble
Adjust the treble by pressing the button to
extend the control and turning it to the left (less
treble), or to the right (more treble). A "detent"
indicates "equalized" treble. Press the button
back in when you have made the adjustment.
Fader - Balance front/rear
Adjust front/rear speaker balance by pressing
the button to extend the control and turning it
to the left (more sound from the rear speakers)
or to the right (more sound from the front
speakers). A "detent" indicates "equalized"
balance. Press the button back in when you
have made the adjustment.
Balance right/left
Adjust left/right speaker balance by pressing
the button to extend the control, and turning itto the left (more sound from the left speakers)
or to the right (more sound from the right
speakers). A "detent" indicates "equalized"
balance. Press the button back in when you
have made the adjustment.
MID EQ level
This function is used to fine-tune the balance
of sound in the speakers. To set the level:
1.
PressSOURCE.
2.
Turn the SOURCE knob, select
ADVANCED MENU
and press SOURCE.
3.
Turn the SOURCE knob, select
AUDIO
SETTINGS
and press SOURCE.
4.
Turn the SOURCE knob, select
MID EQ
LEVEL
and press SOURCE.
5.
Turn the SOURCE knob, select the desired
level and press SOURCE.
6.
PressEXIT.

10 AudioRadio functions HU-650/HU-850
10222
Storing stations
G027191
To store a selected station under one of the
station setting buttons 1-6:
1. Tune to the desired station.
2. Press the button under which the station is
to be stored and keep it depressed. The
audio system sound will be interrupted for
a few seconds and
STORED
will appear in
the display. The station is now stored.
A total of 30 stations can be stored; 6 stations
each in AM1, AM2, FM1, FM2, andFM3.
Storing stations automatically
This function automatically
searches for and stores up to
10 strong AM or FM stations in
a separate memory. If more
than ten stations are found, the
ten strongest ones are stored.
This function is especially useful in areas in
which you are not familiar with radio stations or
their frequencies.
To use the AUTO function:
1.
Select radio mode using the AM or FM
buttons, or by turning the SOURCE knob.
2.
Start the search by pressing AUTO for
more than 2 seconds.
3.
AUTO
appears in the display and a number
of stations with strong signals (max. 10)
from the selected frequency band will be
stored in the auto-store memory. If there
are no stations with sufficient signal
strength,
NO STATION
is displayed.
4.
Press the AUTO button or the arrow keys
on the optional steering wheel controls
briefly to select the stored stations.
When the radio is in auto-store mode,
AUTO
is
shown in the display.
AUTO
disappears when
you return to the normal radio mode.Return to the normal radio mode by pressing
theAM, FM, or EXIT button.
To return to the Auto-store mode, press the
AUTO button briefly.