2009 VOLVO S60 automatic transmission

06 Starting and driving
Starting the vehicle
06``125
WARNING
Always place the gear selector in Park or in
reverse on models with a manual transmis-
sion, and apply the parking brake before
leaving the vehicle. Never leave the vehicle
unattended with the engine running.
Always open garage doors fully before star-
ting the engine inside a garage to ensure
adequate ventilation. The exhaust gases
contain carbon monoxide, which is invisible
and odorless but very poisonous
CAUTION
Automatic transmission
The engine should be idling when you move
the gear selector. Never accelerate until
after you feel the transmission engage!
Accelerating immediately after selecting a
gear will cause harsh engagement and pre-
mature transmission wear.
SelectingP or N when idling at a standstill
for prolonged periods of time will help pre-
vent overheating of the automatic transmis-
sion fluid.Do not race a cold engine immediately after
starting.
Ignition switch and steering wheel lock
0 – Locked position:
Remove the key to lock
the steering wheel
A.
I – Intermediate posi-
tion
B – "radio position":
Certain accessories,
radio, etc. on, daytime
running lights off.
II – Drive position: The
key position when driving.
The vehicle's entire elec-
trical system is con-
nected.
III – Start position:
Release the key when the
engine starts. The key
returns automatically to
the Drive position.
A chime will sound if the key is left in the
ignition and the driver's door is opened.AThe gear selector must be in the P (Park) position (automatic
transmission).BPlease be aware that leaving the key in this position will
increase battery drain.
WARNING
Never turn the key to position 0 while driving
or when the vehicle is being towed.Steering wheel lockThe steering wheel lock might be under tension
when the vehicle is parked.
Turn the steering wheel slightly to free the igni-
tion key.
In order to help reduce vehicle theft, make
sure the steering wheel lock is engaged
before leaving the vehicle.

06 Starting and driving
Economical driving
06
127 Economical driving conserves natural
resources
Better driving economy may be obtained by
thinking ahead, avoiding rapid starts and stops
and adjusting the speed of your vehicle to
immediate traffic conditions. Observe the fol-
lowing rules:•
Bring the engine to normal operating tem-
perature as soon as possible by driving
with a light foot on the accelerator pedal for
the first few minutes of operation. A cold
engine uses more fuel and is subject to
increased wear.
•
Whenever possible, avoid using the vehicle
for driving short distances. This does not
allow the engine to reach normal operating
temperature.
•
Drive carefully and avoid rapid acceleration
and hard braking.
•
Do not exceed posted speed limits.
•
Avoid carrying unnecessary items (extra
load) in the vehicle.
•
Maintain correct tire pressure. Check tire
pressure regularly (when tires are cold).
•
Remove snow tires when threat of snow or
ice has ended.
•
Note that roof racks, ski racks, etc,
increase air resistance and also fuel con-
sumption.
•
Avoid using automatic transmission kick-
down feature unless necessary.
•
However, at higher driving speeds, fuel
consumption will be lower with the air con-
ditioning on and the windows closed than
with the air conditioning off and the win-
dows open.
•
Using the onboard trip computer's fuel
consumption modes can help you learn
how to drive more economically.
Other factors that decrease gas mileage are:
•
Dirty air cleaner
•
Dirty engine oil and clogged oil filter
•
Dragging brakes
•
Incorrect front end alignment.
Some of the above mentioned items and others
are checked at the standard Maintenance
Service intervals.NOTE
Vehicles equipped with automatic transmis-
sions should use (D)rive as often as possible
and avoid using "kickdown" to help improve
fuel economy.
CAUTION
Drive slowly and carefully if going through
standing water (i.e. flooded roadways, etc.).
Damage to the engine could result if excess
water is drawn in through the air intake sys-
tem. Never drive the vehicle in water deeper
than 1 foot (300 mm).

06 Starting and drivingAutomatic transmission (option)
06130
P (Park)
G031105
Use this position when starting the engine or
parking the vehicle.
CAUTION
The vehicle must be stationary when posi-
tionP is selected.The parking brake should be set whenever the
vehicle is parked.
The gear selector is mechanically locked in the
P position (SHIFTLOCK). To release the gear
selector from this position, the engine must be
running (or the ignition key must be in posi-
tionII) and the brake pedal must be depressed.
WARNING
Never leave the vehicle unattended when
the engine is running. If, by mistake, the gear
selector is moved from P, the vehicle may
start moving.R (Reverse)Never engage R while the vehicle is moving.N (Neutral)Neutral - no gear engaged. Use the parking
brake.D (Drive)D is the normal driving position and should be
used as often as possible to help improve fuel
economy. The vehicle should not be moving
when shifting from R to the D position.4 (Intermediate gear)The transmission will shift automatically
between gears 4, 3, 2 or 1 from this position.
The transmission cannot shift up to D from
fourth gear.
3 (Intermediate gear)The transmission will shift automatically
between gears 3, 2 and 1 from this position.
The transmission cannot shift up to fourth gear
orD from third gear.L (Low gears)The transmission is locked in gears 1 and 2
when the selector is in this position.
NOTE
Gears4,3, or L can be used if you are driv-
ing in a mountainous area, towing a trailer
or to increase engine braking effect.
The transmission has a built-in limiter
designed to help prevent excessive engine
speeds (high rpm) when gears 4,3, or L are
selected.

06 Starting and drivingAutomatic transmission (option)
06``131 W - Winter/Wet driving mode -
enhanced vehicle traction
G031107
Press the button at the base of the gear selec-
tor to engage/disengage this driving mode (see
illustration). The
W symbol will appear in the
display (see page 50) when the function is acti-
vated.
This mode may be selected for starting/moving
off on slippery roads. The vehicle starts off in
3rd gear to help maintain traction. First and
second gears will only be used during kick-
down.
Shift gate positions
G031109
The gear selector can be moved freely between
N and D.
Depressing the button on the front of the gear
selector knob enables you to move the gear
selector to positions P, R, N, D, 4, 3 and L .
"Kickdown"Automatic shift to a lower gear (kickdown) is
achieved by depressing the accelerator pedal
fully and briskly. An upshift will occur when
approaching the top speed for a particular gear
or by releasing the accelerator pedal slightly.
Kickdown can be used for maximum acceler-
ation or when passing at highway speeds.Cold startsWhen driving before the engine has reached its
normal operating temperature, the transmis-
sion will shift up at slightly higher engine
speeds to heat the three-way catalytic con-
verter as quickly as possible.Automatic transmission - adaptive
systemThe automatic transmission is controlled by an
adaptive control system that constantly moni-
tors the way in which the transmission func-
tions. It senses and adapts each gear shift for
optimal performance.

06 Starting and drivingAutomatic transmission (option)
06132
Geartronic
G027997
P (Park)Use this position when starting the engine or
parking the vehicle.
CAUTION
The vehicle must be stationary when posi-
tionP is selected.The parking brake should also be set whenever
the vehicle is parked.
The gear selector is mechanically locked in the
P position (SHIFTLOCK). To release the gear
selector from this position, the engine must berunning (or the ignition key must be in posi-
tionII) and the brake pedal must be depressed.
WARNING
Never leave the vehicle unattended when
the engine is running. If, by mistake, the gear
selector is moved from P, the vehicle may
start moving.R (Reverse)Never engage R while the vehicle is moving.N (Neutral)Neutral - no gear engaged. Use the parking
brake.D (Drive)D is the normal driving position and should be
used as often as possible to help improve fuel
economy. The vehicle should not be moving
when shifting from R to the D position.
Manual shifting
G020237
Shift gate positionsYou can move the gear selector freely between
theMAN and D positions to select forward
gears while driving. Gears 3, 4, 5, and 6 (where
applicable) have a "lock-up" function which
reduces engine speed and helps save fuel.
Depress the button on the front of the gear
selector knob to move between the R, N, D,
andP positions.
NOTE
Reverse, Neutral, and Park cannot be
selected in Geartronic mode.

06 Starting and drivingAutomatic transmission (option)
06
133
The currently selected gear will be displayed in
the instrument panel (see page 50).•
To access the MAN shifting position from
D, move the gear selector to the left to
MAN.
•
To return to the D position from MAN,
move the gear selector to the right.
While drivingIf you select the MAN position while driving, the
gear that was being used in the D position will
also initially be selected in MAN position.•
Move the gear selector forward (toward
"+") to shift to a higher gear or rearward
(toward "–") to shift to a lower gear.
•
If you hold the gear selector toward "–", the
transmission will downshift one gear and
will utilize the braking power of the engine.
If the current speed is too high for using a
lower gear, the downshift will not occur
until the speed has decreased enough to
allow the lower gear to be used.
•
If you slow down to a very low speed, the
transmission will automatically shift down.
•
When starting in the MAN position, 3rd
gear is the highest gear that may be
selected.
NOTE
Kickdown does not function when the trans-
mission is in the manual shift (Geartronic)
mode.The gear selector must be in the D
position.KickdownAutomatic shift to a lower gear (kickdown) is
achieved by depressing the accelerator pedal
fully and briskly. An upshift will occur when
approaching the top speed for a particular gear
or by releasing the accelerator pedal slightly.
Kickdown can be used for maximum acceler-
ation or when passing at highway speeds.
Kickdown does not function when the trans-
mission is in the manual shift (Geartronic)
mode.W - Winter/Wet driving mode -
enhanced vehicle tractionPlease refer to the information on page 131.

06 Starting and driving
Towing a trailer
06``143
Volvo recommends the use of Volvo trailer
hitches that are specially designed for the vehi-
cle.•
Maximum trailer weight recommended by
Volvo is: Trailers without brakes: 1650 lbs
(750 kg) Trailers with brakes: 2" (50 mm)
ball - 3300 lbs* (1500 kg), 1 7/8 " (47 mm)
ball - 2000 lbs (900 kg). Observe the legal
requirements of the state/province in
which the vehicles are
•
All Volvo models are equipped with
energy-absorbing shock-mounted bump-
ers. Trailer hitch installation should not
interfere with the proper operation of this
bumper system.
Trailer towing does not normally present any
particular problems, but take into considera-
tion:
•
Increase tire pressure to recommended
full. See section "Wheels and tires."
•
When your vehicle is new, avoid towing
heavy trailers during the first 620 miles
(1000 km).
•
Recommended hitch tongue load is: Trailer
weightsbelow 2,650 lbs (1,200 kg) -
110 lbs (50 kg) Trailer weights above
2,650 lbs (1,200 kg) - 165 lbs (75 kg)
•
Maximum speed when towing a trailer:
50 mph (80 km/h).
•
Engine and transmission are subject to
increased loads. Therefore, engine coolant
temperature should be closely watched
when driving in hot climates or hilly terrain.
Use a lower gear and turn off the air con-
ditioner if the temperature gauge needle
enters the red range.
•
If the automatic transmission begins to
overheat, a message will be displayed in
the text window.
•
Avoid overload and other abusive opera-
tion.
•
Hauling a trailer affects handling, durabil-
ity, and economy.
•
It is necessary to balance trailer brakes
with the towing vehicle brakes to provide a
safe stop (check and observe state/local
regulations).
•
Do not connect the trailer's brake system
directly to the vehicle's brake system.
•
More frequent vehicle maintenance is
required.
•
Remove the ball and drawbar assembly
when the hitch is not being used.
•
Volvo recommends the use of synthetic
engine oil when towing a trailer over long
distances or in mountainous areas.
WARNING
•
Bumper-attached trailer hitches must
not be used on Volvos, nor should
safety chains be attached to the
bumper.
•
Trailer hitches attaching to the vehicle
rear axle must not be used.
•
Never connect a trailer's hydraulic
brake system directly to the vehicle
brake system, nor a trailer's lighting
system directly to the vehicle lighting
system. Consult your nearest trained
and qualified Volvo service technician
for correct installation.
•
When towing a trailer, the trailer's safety
wire must be correctly fastened to the
hole or hook provided in the trailer hitch
on the vehicle. The safety wire should
never be fastened to or wound around
the drawbar ball.NOTE
When parking the vehicle with a trailer on a
hill, apply the parking brake before putting
the gear selector in P (first/reverse gear on
manual transmissions). Always follow the
trailer manufacturer's recommendations for
wheel chocking.

07 Wheels and tires
Changing wheels
07``169
G020331
Insert flat end of lug wrench and turn/pull straight
outThe spare wheel is located under the carpet on
the trunk floor. The jack and crank are secured
in the wheel recess.
There are two jack attachment points on each
side of the vehicle (see illustration below).To change a wheel:1. Engage the parking brake.
2.
Put the gear selector in P (automatic trans-
mission) or reverse (manual transmission).
G020332
Loosen the wheel bolts3. Remove the wheel cap (where applicable)
using the lug wrench in the tool bag.
4. With the vehicle still on the ground, use the
lug wrench to loosen the wheel bolts 1/2 -
1 turn by exerting downward pressure.
Turn the bolts counterclockwise to loosen.
CAUTION
•
The vehicle must not be driven with
wheels of different dimensions or with a
spare tire other than the one that came
with the vehicle. The use of different size
wheels can seriously damage your vehi-
cle's transmission.
•
Correct tightening torque on wheel
bolts must be observed. The wheel
bolts should never be greased or lubri-
cated. The extended, chromed wheel
bolts must not be used with steel rims,
as they make it impossible to fit the hub
caps.
•
Locking wheel bolts can be used on
both aluminum and steel wheels. If hub
caps are used on steel wheels, the lock-
ing wheel bolt should be mounted in the
hole as far from the tire's inflation valve
as possible. It would otherwise not be
possible to mount the hub cap on the
wheel.