2009 TOYOTA YARIS HATCHBACK child restraint

101
1-7. Safety information
1
Before driving
CAUTION
n
Child restraint precautions
lMake sure you have complied with all installation instructions provided by
the child restraint manufacturer and that the system is properly secured. If
it is not secured properly, it may cause death or serious injury to the child
in the event of a sudden stop or accident.
n Child restraint lock function belt precaution
Do not allow children to play with the child restraint lock function belt. If the
belt becomes twisted around a child’s neck, it will not be possible to pull the
belt out leading to choking or other serious injuries that could result in death.
If this occurs and the buckle cannot be unfastened, scissors should be used
to cut the belt.
n When the child restrain t system is not in use
l Keep the child restraint system properly secured on the seat even if it is
not in use. Do not store the restraint unsecured in the passenger compart-
ment.
l If it is necessary to detach the child restraint system, remove it from the
vehicle or store it securely in the luggage compartment. This will prevent it
from injuring passengers in the event of a sudden stop or accident.

102
1-7. Safety information
Installing child restraints
Follow the child restraint system manufacturer's instructions. Firmly
secure child restraints to the rear seats using the LATCH anchors or
a seat belt. Attach the top tether strap when installing a child
restraint.
The lap/shoulder belt can be used if your child restraint system is
not compatible with the LATCH (Low er Anchors and Tethers for Chil-
dren) system.
Child restraint LATCH anchors
LATCH anchors are provided
for the outside rear seats. (But -
tons displaying the location of
the anchors are att
ached to the
seats.)
Seat belts equipped with a
child restraint locking mecha -
nism (ALR/ELR belts except
d

river’s seat belt) ( →P. 5 2 )

104 1-7. Safety information
Installation with LATCH system
Fold down the seatback and
back to the most upright position
until it locks into place.
Type A Widen the gap between
the seat cushion and
seatba
ck slightly.
Latch the hooks of the
lower straps onto the
L
ATCH anchors and
tighten the lower straps.
If the child restraint has a
top tether strap, the top
te
ther strap should be
latched onto the top
tether strap anchor.
( → P. 109 )
For owners in Canada:
The symbol on a child restraint
system indicates the
presence of
a lower connector system.
Most
upright
position
Canada
only

105
1-7. Safety information
1
Before driving
Type B
Widen the gap between
the seat cushion and
seatba
ck slightly.
Latch the buckles onto
the LATCH anchors.
If the child restraint has a
top tether strap, the top
te
ther strap should be
latched onto the top
tether strap anchor.
( → P. 109 )
For owners in Canada:
The symbol on a child restraint
system indicates the
presence of
a lower connector system.
Installing child restraints using a seat belt (child restraint lock function belt)
n Rear facing ⎯ Infant seat/convertible seat
Place the child seat on the rear
se
at facing the rear of the vehi -
cle.
Canada
only

107
1-7. Safety information
1
Before driving
Run the seat belt through the
child seat and insert the plate
into the buckle. Make sure that
the belt is not twisted.
Fully extend the shoulder belt
and

then allow it to retract
slightly in order to activate the
ALR lock mode.
Lock mode allows the seat belt to
retract only.
While pushing the child seat
down into the rear seat, allow the
shoulder belt to retract until the
child seat is securely in place.
After the shoulder belt has
retracted to a point where there is
no slack in the belt, pull the belt to
check that it cannot be extended.
If the child restraint has a top te ther strap, the top tether strap
should be latched onto the top tether strap anchor. ( →P. 1 0 9 )

108 1-7. Safety information
nBooster seat
Place the booster seat on the
sea
t facing the front of the vehi -
cle.
Sit the child in the booster seat.
Fit the seat belt to the bo
oster
seat according to the manufac -
turer's instructions and insert the
p
late into the buckle. Make sure
that the belt is not twisted.
Check that the shoulder belt is
correctly positioned over the
child's shoulder, and that the lap
belt is as low as possible.
( →P. 5 2 )
Removing a child restraint installed with a seat belt
Push the buckle release button
and fully retract the seat belt.

109
1-7. Safety information
1
Before driving
Child restraint systems with a top tether strap
Remove the luggage cover. (
→P. 226 )
Remove the deck board and auxiliary boxes. ( →P. 2 2 5 )
Remove the head restraint.
Split rear seats (type A), Non-split rear seat Latch the hook onto the anchor
b
racket and tighten the top tether
strap.
Make sure the top tether strap is
securely latched.

110 1-7. Safety information
Split rear seats (type B)Latch the hook onto the anchor
b
racket and tighten the top tether
strap.
Make sure the top tether strap is
securely latched.
Non-split rear seat only:
Reinstall the head restraint.
Reinstall the auxiliary boxes, deck board and luggage cover.
n Laws and regulations pertaining to anchorages
The LATCH system conforms to FMVSS225 or CMVSS210.2.
Child restraint systems conforming to FMVSS213 or CMVSS213 specifica -
tions can be used.
This vehicle is designed to conform to the SAE J1819.