2009 SKODA YETI ignition

Intelligent Technology
169
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
If there is a fault in the power steering, the warning light
 or  lights up in the instru-
ment cluster
⇒page 32.
WARNING
Contact your specialist
garage if the power steering is defective.
Tyre inflation pressu
re-control system*
The tyre inflation pressure-control system compares with the aid of the ABS sensors the speed and also the rolling circumference of the individual wheels. If the rolling circumference of a wheel is changed, the warning light
 lights up in the instrument
cluster
⇒page 35 and an audible signal sounds.
The rolling circumference of the tyre
can change if:•
the tyre inflation pressure is too low,
•
the structure of the tyre is damaged,
•
the vehicle is loaded on one side,
•
the wheels of an axle are loaded heavily (e.g. when towing a trailer or when driving
uphill or downhill),•
snow chains are mounted,
•
the temporary spare wheel is mounted,
•
one wheel per axle was changed.
Basic setting of tyre inflation pressure-control system After changing the tyre inflation pressures or after changing one or several wheels, the position of a wheel on the vehicle (e.g. ex
changing the wheels between the axles) or
when the warning light lights up while drivin
g, a basic setting of the system must be
carried out as follows.•
Inflate all tyres to the specified inflation pressure
⇒page 215.
•
Switch on the ignition.
•
Press button
⇒fig. 156
for more than 2 seconds. While pressing the button,
the warning light
 lights up. At the same time the memory of the system is erased
and the new calibration is started, which is confirmed with an audible signal and then the warning light
 goes out.
•
If the warning light
 does not go out after the basic
setting, there is a fault in the
system. Have the vehicle inspected by your nearest specialist garage. Warning light
 lights up
If the tyre inflation pressure of at least one
wheel is insufficiently inflated in comparison
to the stored basic va
lue, the warning light
 ⇒
lights up.
Warning light
 flashes
If the warning light flashes, there is a system fault. Have the vehicle inspected by your nearest specialist garage.
WARNING
•
When the warning light
 lights up, immediately reduce the speed and
avoid sudden steering and brake manoeuvr
es. Please stop the vehicle without
delay at the nearest possible stop and in
spect the tyres and their inflation pres-
sures.•
The driver is responsible for the correc
t tyre inflation pressures. For this
reason, the tyre inflation pressu
res must be checked regularly.
•
Under certain circumstances (e.g. sporty style of driving, wintry or unpaved
roads) the warning light
 can be delayed or does not light up at all.
•
The tyre inflation pressure-control system does not take away the respon-
sability from the driver for the
correct tyre inflation pressure.
Fig. 156 Button for setting the tyre infla- tion pressure control value
 
sgg.6.book Page 169 Thursday, September 24, 2009 2:32 PM

Intelligent Technology
171
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
•
TCS Off-road
⇒page 165,
•
ABS Off-road
⇒page 167.
Switch on Off-road The Off-road mode is switched on by pressing the button
⇒page 170, fig. 158
. The
warning light in the button lights up. The wa
rning light lights up in the instrument
cluster if the system is switched on
 ⇒page 38.
Switch off Off-road The Off-road mode is switched off by repe
ated pressing of the button. The warning
light in the button goes out. When switching
off the ignition, the Off-road mode is also
switched off and can be switched on again, if necessary, after switching on the ignition. If the engine is switched off by accident an
d restarted within 30 seconds, the Off-road
mode remains switched on. All four wheels must be fitted with the same tyres in order to achieve proper operation of the Off-road mode. Differing rolling circum
ferences of the tyres can lead to an unde-
sirable reduction in the engine output.
WARNING
•
Always adjust your speed to suit weat
her, road and traffic conditions. The
increased safety must not tempt you to take a greater safety risk than otherwise - risk of accident!•
The Off-road equipment can also not overcome the physical limits of your
vehicle.•
The effect of the Off-road equipm
ent depends as well on the tyres.
•
The Off-road equipment
is not designed for the use on common roads.
Start-Off Assist*The Start-Off Assist enhances the driving comfort and can be used when starting off, in particular on a slope. When the vehicle is stationary, the Start-Off Assist is activated after switching it on using the button for the Off-road mode
⇒page 170, fig. 158
.
Operating principle When depressing the accelerator pedal fully, the engine speed required for the start- up procedure of the stationary vehicle is restricted. The overspeed trip unit is automat-ically deactivated after terminating the start-up procedure. As part of the Assist System, the accelerator pedal is adapted in its characteristics for an easier start-off on slippery and loose soil.Downhill Drive Support*Operating principle The Downhill Drive Support maintains a cons
tant speed on a steep downhill section
when driving forwards and backwards by
automatically intervening in the brake
system of all wheels. It prevents the wheels locking because the ABS remains active. The warning light
 in the information display of the instrument cluster indicates that
the Downhill Drive Support is available
⇒page 38.
The vehicle speed, which is maintained by the Assist System, is selected by the driver while driving on a downhill section as of the
moment the first intervention of the Assist
System is performed or else, while driving on a downhill section, the driver must control the vehicle speed until the Assist System intervenes for the first time. When the Assist System actively intervenes, this is indicated by the warning light flashing or by a pulsating movement of the brake pedal,
similar to the intervention of the ABS.
The Downhill Drive Support is available in the speed range of 2 km/h up to 30 km/h. If the gear is engaged and the clutch pedal is
not pressed, the lower limit of the idling
speed corresponds to the respective gear which is engaged. You can increase or reduce the speed, even when no gear is engaged, by operating the accelerator or brake pedal. Thus the function
is always interrupted and is reactivated
afterwards. The Downhill Drive Support is activated auto
matically if the following conditions are
met:•
the Off-road mode is switched on and the warning light
 lights up in the instru-
ment cluster,•
the engine of the vehicle is running and either the 1st, 2nd, 3rd gear, the reverse
gear or no gear is engaged,•
the speed is less than 30 km/h,
sgg.6.book Page 171 Thursday, September 24, 2009 2:32 PM

Driving and the Environment
174
Catalytic converterProper operation of the emission cont
rol system (catalytic converter) is
of major significance for driving your vehicle in an environmentally conscious way.Please refer to the following guidelines: – For vehicles with petrol engine only refuel with unleaded petrol
⇒page 200,
“Grades of petrol”.
– Never run the fuel tank completely empty.– Do not switch off the ignition while you are driving the vehicle. – Do not pour too much oil into the engine
⇒page 206, “Replenishing engine oil”.
– Do not tow-start the vehicle over a distance of more than 50 metres
⇒page 230,
“Tow-starting and towing vehicle”.
If you drive your vehicle in a country in
which unleaded petrol is not available, you
must have the catalytic converter replaced la
ter when driving the ve
hicle into a country
in which use of a catalyti
c converter is mandatory.
WARNING
•
In view of the high temperatures which may be produced in the catalytic
converter, one should always park a vehicle in such a way that the catalytic converter cannot come into contact with easily flammable materials below the vehicle - a risk of fire!•
Never use additional underbody protection or corrosion-protection agents
for the exhaust pipes, catalytic converters or heat shields. Such substances might ignite when driving - risk of fire!
Caution
•
On vehicles fitted with a catalytic converte
r, never let the fuel tank run completely
empty. An irregular fuel supply can result in poor ignition or misfiring. Unburnt fuel may get into the exhaust system an
d damage the cata
lytic converter.
•
Filling the tank even only once with lead
ed petrol will result in the catalytic
converter being destroyed.•
If you detect misfir
ing, a drop in performance or
irregular engine running when
driving, reduce your speed immediately and have the vehicle inspected by the nearest specialist garage. The symptoms described ma
y be caused by a fault in the ignition
system. Unburnt fuel may get into the exhaust system and damage the catalytic converter.
For the sake of the environment
Even if the exhaust system is operating pr
operly, a sulphur-like exhaust odour may be
produced under certain oper
ating conditions of the en
gine. This de
pends on the
sulphur content of the fuel. It is often sufficient to refuel with unleaded premium-grade petrol of a different brand or at a different filling station.Driving in an economical and environmentally conscious mannerGeneral Your personal style of driving is a major factor.Your fuel consumption, any pollution of
the environmental and the wear-and-tear to
the engine, brakes and tyres, depend essentially on three factors:•
your personal style of driving,
•
the conditions under which
your vehicle is operated,
•
technical aspects.
You can easily improve your fuel economy by
10 - 15 percent by driving in an econom-
ical way with foresight. This section is intended to provide you with a number of tips on how to protect the environment and at the same time save money. The fuel consumption can naturally also be
influenced by factors which are beyond the
driver's control. It is, for example, normal
for the fuel consumption to increase in
winter and under worsened cond
itions such as poor road conditions, towing a trailer,
etc.
sgg.6.book Page 174 Thursday, September 24, 2009 2:32 PM

Taking care of your vehicle and cleaning the vehicle
194
There are no particular points to note be
fore washing your vehicle in an automatic
vehicle wash system other than the usua
l precautionary measures (closing the
windows and the sliding/tilting roof etc.). If you have any particular atta
ched parts fitted to your car
- such as spoiler, roof rack
system, two-way radio aerial - it is best to first of all consult the operator of the car wash plant. It is important to degrease
the lips of the windscreen
wiper rubbers after passing
through the automatic
vehicle wash system.
Washing vehicle by handIt is important to first soften the dirt with
plenty of water and rinse it off as thoroughly
as possible before washin
g your vehicle by hand.
One should then clean the vehicle using a soft
washing sponge
, washing glove
or a
washing brush
and only slight pressure. Work from
the top to the bottom - beginning
with the roof. Only place slight pressure on
the vehicle paintwork
during cleaning. Only
use a
car shampoo
for stubborn dirt.
Wash out the sponge or washing glove thoroughly at short intervals.Clean wheels, door sills and similar parts last. Use a second sponge for such areas.Rinse off the vehicle well after giving it a wash and dry it off using a chamois leather.
WARNING
•
The ignition should always be switched off when you wash your vehicle -
risk of accident!•
Protect your hands and arms from sharp-edged metal parts when you are
cleaning the underfloor, the inside of
the wheel housings or
the wheel trims -
risk of cuts.
Caution
•
Do not wash your vehicle in bright
sunlight - risk of paint damage.
•
Ensure that the jet of water is not aimed di
rectly at the locking cylinders or at the
door and panel joints if you spray your vehi
cle in winter down with a hose - risk of
freezing.
•
Do not use any insect sponges, rough kitc
hen sponges or similar cleaning products
- risk of damage to the surface of paintwork.
For the sake of the environment
Only wash your vehicle at wa
shing bays specifically reserved for this purpose. This
ensures that no water which may be contaminated by oil flows into the sewage system. It is not even permitted to wash your vehicl
e in certain areas except at such specific
washing bays.Washing with a high-pressure cleanerWhen you wash your vehicle with a high-press
ure cleaner, it is essential to comply with
the instructions for use of the cleaning equi
pment. This applies in particular to the
pressure
used and to the
spraying distance
. Maintain a sufficiently large distance to
soft materials such as rubber hoses or insulation material. On no account use
circular spray nozzles
or so-called
dirt cutters
!
WARNING
It is particularly important that you do not clean tyres with circular spray jets. Visible but also invisible
damage to tyres may occur ev
en at a relatively large
spraying distance and if sprayed only for a short time - risk of accident!
Caution
The water containing wax must be no hotter
than 60°C, otherwise the vehicle can be
damaged.Wax treatmentGood wax treatment is an effective way of
protecting the paintwork from harmful envi-
ronmental influences and
minor mechanical damage.
The vehicle must be treated with a high-quali
ty hard wax polish at the latest, when no
more drops form on the clean paintwork.
sgg.6.book Page 194 Thursday, September 24, 2009 2:32 PM

Taking care of your vehicle and cleaning the vehicle
197
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Underbody protectionThe underside of your vehicle is protected for life against chemical and mechanical influences. One cannot, however, complete
ly rule out damage to the
protective layer
when
driving so we recommend that you inspect the protective layer on the underside of your vehicle and on the
chassis at certain intervals - this is best done at the beginning
and end of the winter - and to touch up any damaged areas. The authorised Škoda Service Partners have suitable
spray products
available as well
as the necessary equipment and are familiar with the instructions for use. It is therefore best to have such touch-up
work or additional corrosion
protection measures carried
out by an authorised Škoda Service Partner.
WARNING
Never use additional underbody protection or corrosion-protection agents for the exhaust pipes, catalytic converters, di
esel particle filter or heat shields.
When the engine reaches its operating
temperature, these substances might
ignite - risk of fire!Protection of hollow spacesAll the cavities of your vehicle which are at risk from corrosion are protected for life by a layer of
protective wax
applied in the factory.
This wax protection does not require to be inspected or re-treated. Please remove any small amount of wax which flows out of the cavities at high temperatures with a plastic scraper and clean the spot using petroleum cleaner.
WARNING
Safety and environmental pr
otection regulations should observed when using
petroleum cleaner to remove wax - a risk of fire!
Engine compartmentGood corrosion protection is very importan
t, particularly in winter when one often
drives over its salt-strewn roads. One should therefore clean the whole engine compartment before and after the salt spread
ing period and treat with preservative in
order to prevent the salt from being destructive. The authorised Škoda Service Partners have the cleaning agents and preservatives recommended by the manufacturer and also the required equipment.
WARNING
•
It is necessary to observ
e the guidelines given in the chapter before working
on the engine compartment
⇒page 204, “Working in the engine compart-
ment”.•
Let the engine cool down before cleaning the engine compartment.Caution
•
Engine cleaning may be only be un
dertaken when the ignition is off.
•
It is recommended to cover the generator before washing the engine compart-
ment.
For the sake of the environment
The dirty water produced by washing the engine has washed away petrol, and residues of grease and oil and should therefore be
cleaned by an oil separator. This is why
engine washing should only be undertaken in
a specialist garage or at a fueling station
(when these are fitted with the required equipment).Care of the interior of vehiclePlastic parts, artificial leather and clothsYou can clean plastic parts and artificial le
ather with a moist cloth. You should only
treat such parts with special
solvent-free plastic cleaning and care products
it does
prove to be adequate.
sgg.6.book Page 197 Thursday, September 24, 2009 2:32 PM

Inspecting and replenishing
204
Caution
Never open the bonnet using the locking lever - danger of causing damage.Working in the engine compartment Particular care is required when carrying out any work in the engine compartment!There is a risk of injuries, scalding, acci
dents and fire when working in the engine
compartment, e.g. inspecting and replenishing oil and other fluids. For this reason, it is essential to comply with the warning instructions stated below and with the general applicable rules of safe
ty. The engine compartment of your car
is a hazardous area
⇒
.
WARNING
•
Never open the bonnet if
you see that steam or coolant is flowing out of the
engine compartment - risk of scalding!
Wait long enough until the steam or
coolant has stopped escaping.•
Switch off the engine and pull out the ignition key.
•
Apply the handbrake firmly.
•
If your vehicle is fitted with a manual
gearbox, move the gearshift lever into
Neutral, or if it is fitted with automatic gearbox, move the selector lever into position P.•
Allow the engine to cool down.
•
Keep children clear of the engine compartment.
•
Never spill oil and other fluids over the hot engine. Such fluids (e.g. the anti-
freeze contained in the coolant) may ignite!•
Avoid short circuits in the electrical system - particularly on the battery.
•
Never place your hand into the radiator fan as long as the engine is still
warm. The fan might suddenly start running!•
Never open the cap of the coolant expans
ion bottle as long as the engine is
still warm. The cooling
system is pressurized!
•
Cover over the cap of the coolant expansion reservoir with a large cloth
when opening it as protection for your
face, hands and arms from hot steam or
hot coolant.•
Do not let objects, such as e.g cleaning cloth or tools lie in the engine
compartment.•
If you wish to work under the vehicl
e, you must secure the vehicle from
rolling away and support it with suitable supporting blocks: the car jack is not sufficient for this - risk of injury!•
In cases where it be necessary to carry out inspection work when the engine
is running there is an additional risk fr
om rotating parts (e.g. the V-ribbed belt,
alternator, radiator fan) and from the high-voltage ignition system. Please observe in addition the following:
− Never touch the electrical cabl
es of the ignition system.
− Absolutely avoid any jewellery, loose it
ems of clothing or long hair from
getting into the rotating parts of the
engine - Hazard! Therefore remove any
jewellery beforehand, tie up your hair and wear tight fitting clothing.
•
Please also comply with the warnin
g instructions st
ated below when
carrying out any essential work on the fu
el system or on th
e electrical system:
− Always separate the car battery from the electrical system. − Do not smoke. − Never carry out any work close to naked flames. − Always keep a working fire
extinguisher at hand.
Caution
When replenishing fluids in the engine, always
ensure that the fluids are on no account
mixed up. This may result in major oper
ating problems and also vehicle damage!
WARNING (continued)
sgg.6.book Page 204 Thursday, September 24, 2009 2:32 PM

Inspecting and replenishing
210
Caution
Brake fluid damages the paintwork of the vehicle.
For the sake of the environment
In view of the problems involved with proper
disposal of brake fluid, the special tools
and the professional knowledge required, you should have the brake fluid replaced by authorised Škoda Service Partners.BatteryWorking on the batteryFig. 175 Engine compartment: Polyester cover
of the vehicle battery / plastic cover of the
vehicle batteryThe battery is located in the engine compar
tment in a polyester co
ver or in a plastic
cover*. – Open the battery cover in direction of arrow or press the interlock on the side
of the battery cover in direction of arrow
⇒fig. 175
, fold the cover up and
remove the battery.
– The installation of the battery co
ver takes place in the reverse order.
Removal and installation of the battery is no
t recommended since it can, under certain
circumstances, lead to major dama
ge. Contact a specialist garage.
There is a risk of injuries, scalding, accidents and burns when carrying out any work on the battery and on the electrical system. For th
is reason, it is essential to comply with
the warning instructions
⇒
stated below and with the general applicable rules of
safety.
WARNING
•
The battery acid is strongly corrosive
and must, therefore, be handled with
the greatest of care. Always wear prot
ective gloves, eye and skin protection
when handling batteries. Corrosive fumes in
the air irritate the air passages and
lead to conjunctivitis and inflammation of
the air passages in the lungs. Battery
acid corrodes dental enamel and crea
tes deep wounds after contact with the
skin which take a long time to heal. Repeated contact with diluted acids causes skin diseases (inflammations, ulcers, slin cracks). Acids coming into contact with water are diluted accompanied by significant development of heat.•
Do not tilt the battery otherwise battery electrolyte may flow out of the
battery vent openings. Protect the eyes wi
th safety glasses or a shield! There is
the danger of suffering blindness! If an
y battery electrolyte
gets into your eye,
rinse out your eye immediately with clear water for several minutes. Contact a doctor without delay.•
Splashes of acid on your skin or clothes should be neutralised as soon as
possible using soap suds and then rinsed with plenty of water. Contact a doctor immediately if you swal
low battery electrolyte.
•
Keep batteries out of the reach of children.
•
Hydrogen is released when you charge
a battery and a highly explosive gas
mixture is produced. An explosion can be
caused through sparkling over during
unclamping or loosening of the cable plug while the ignition is on.•
Bridging of the poles will create a short circuit (e.g. through metal objects,
cables). Possible consequences of a short circuit: Melting of lead struts, explo- sion and burning of the battery, jets of acid spurting out.•
It is prohi bi te d t o wo rk w ith a na ke d fl a m e an d lig ht , t o s m oke or t o c ar r y out
any activities which produc
e sparks. Avoid creating sp
arks when working with
cables and electrical devices. Strong
sparking represents a risk of injury.
•
Before carrying out any work on the el
ectrical system, swit
ch off the engine,
the ignition as well as all electrical components and disconnect the negative
A1
A2
sgg.6.book Page 210 Thursday, September 24, 2009 2:32 PM

Inspecting and replenishing
211
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
cable (-) on the battery. If you wish to replace a bulb it is sufficient to switch off the appropriate light.•
Never charge a frozen or thawed battery - risk of explosion and caustic
burns! Replace a frozen battery.•
Never use a battery which is damaged
- risk of explosion! Immediately
replace a damaged battery.
Caution
•
You must only disconnect the battery if th
e ignition is switched off, otherwise the
electrical system (electronic components
) of the vehicle may be damaged. When
disconnecting the battery from the electrical system of the vehicle, first disconnect the negative terminal (-) of the battery. Th
en disconnect the positive terminal (+).
•
When reconnecting the battery, first connect the positive terminal (+) and only
then the negative terminal (-) of the batt
ery. You must on no account connect the
cables wrongly - risk of a cable fire.•
Ensure that battery acid does not come
into contact with th
e vehicle body other-
wise damage could occur to the paintwork.•
Do not place the battery in
direct daylight in order to protect the battery housing
from the effects of ultra-violet light.
For the sake of the environment
A removed battery is a special type of waste which is harmful to the environment - contact your specialist garage re
garding disposing of the battery.
Note
Please also refer to the guidelines
⇒page 213, also after connecting the battery.
Battery with a two-tone indicatorAn indicator for the electrolyte level, the so-called magic eye
⇒fig. 176
, is located on
the top of the battery. The indicator changes its colour in line with the electrolyte level in the battery. Air bubbles can influence the colour of the in
dicator. For this reason carefully knock on
the indicator before carrying out the check.•
Black colour - electrolyte level is correct.
•
Colourless or light yellow colour - electrolyte level too low, the battery must be
replaced. Batteries, which are more than 5 years old, must be replaced. We recommend you have the battery checked or repl
aced by a specialist garage.
Caution
If the vehicle has not been driven for more th
an 3 to 4 weeks, the battery will discharge
because certain electrical co
mponents consume electricity (e.g. control units) also in
idle state. You can prevent the discharging of
the battery by disconnecting the negative
terminal or charging the battery constantly
with a very low charging current. Please
also refer to the notes when working on the battery
⇒page 210.
Note
•
Batteries with two-tone indicator, which
are mounted as of factory, are marked
with a code which always begins with
5K0
. The exact marking can be e.g.
5K0 915 105 D
.
WARNING (continued)
Fig. 176 The battery: Show
sgg.6.book Page 211 Thursday, September 24, 2009 2:32 PM