2009 SKODA YETI technical data

Instruments and Indicator/Warning Lights
17
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Engine revolutions counterThe red zone of the rev counter scale
⇒page 16, fig. 15
indicates the range in
which the engine control unit begins to limi
t the engine speed. The engine control unit
restricts the engine speed to a steady limit value. Shift into the next higher gear or select th
e selector lever position D of the automatic
gearbox before reaching the red zone of the rev counter scale. Avoid high engine speeds du
ring the driving time and before the engine has been
warmed up to operating temperature
⇒page 173.
For the sake of the environment
Shifting up early helps you sa
ve fuel and reduce the operating noise of your vehicle.
SpeedometerWarning against excessive speeds* An acoustic warning signal will sound when the vehicle speed exceeds 120 kilometres per hour. The acoustic warning signal will sw
itch off again when the vehicle speed goes
below this speed limit.
Note
This function is only valid for some countries.Coolant temperature gaugeThe coolant temperature gauge
⇒page 16, fig. 15
operates only when the ignition
is switched on. In order to avoid any damage to the engine,
please pay attention to
the following notes
regarding the temperature ranges:
Cold range If the pointer is in the left-hand area of the scale it means that the engine has not yet reached its operating temperature. Avoid runni
ng at high engine speeds, at full throttle
and at severe engine loads. The operating range The engine has reached its operating temperature as soon as the pointer moves into the mid-range of the scale. The pointer may
also move further to the right at high
engine loads and high outside temperatures. This is not critical provided the warning symbol
 in the instrument cl
uster does not flash.
If the symbol
 in the instrument cluster flashes it means that either the coolant
temperature
is too high or the coolant
level
is too low. Observe the guidelines
⇒ page 34, “Coolant temperature/ Coolant quantity
”.
WARNING
Pay attention to the warning notes
⇒page 204, “Working in the engine
compartment” before opening the bonn
et and inspecting the coolant level.
Caution
Additional headlights and other attached components in front of the fresh air inlet impair the cooling efficiency
of the coolant. There is then a risk of the engine over-
heating at high outside temperatures and high engine loads!Fuel gaugeThe fuel gauge
⇒page 16, fig. 15
only operates when the ignition is switched on.
The fuel tank has a capacity of
about 60 litres. The warning symbol
 in the instrument
cluster lights up when the pointer reaches the reserve marking. There are now about 10.5 litres of fuel remaining in the ta
nk. This symbol is a reminder for you,
that you
must refuel
.
The following will be displayed in the information display*:
Please refuel!
An audible signal sounds as an additional warning signal.
A1
A4
A6
sgg.6.book Page 17 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
19
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
The following will be displayed in the information display*:
Service in ... km or... days
The kilometre indicator or the days indicator reduces in steps of 100 km. or days until the service due date is reached. A flashing key symbol

and the text
Service
appears in the display for 20 seconds
as soon as the due date for the service is reached. The following will be displayed in the information display*:
Service now!
Display regarding the distance and days until the following service interval You can use the button to display the remaining distance driven and the days until the next service interval
⇒page 16.
A key symbol

and a display regarding the remaining kilometers appear for 10
second in the display. At the same time, a display appears regarding the remaining days until the next service interval. On vehicles which are equipped with inform
ation display*, you ca
n call up this infor-
mation in the following menu on
⇒page 24:
„
SETUP (Settings)
„
Service Interval (Service)
„
Info
The following will be displayed in the information display* for 10 seconds:
Service in ... km or... days
Resetting Service Interval Display It is only possible to reset the Service Interval Display, if a service message or at least a pre-warning is shown on the display of the instrument cluster. We recommend having this resetting performed by a specialist garage.The specialist garage:•
resets the memory of the display after the appropriate inspection;
•
makes an entry in the Service schedule;
•
affix the sticker with the entry of the following service interval to the side of the
dash panel on the driver's side. Reset the service interval displays by using the reset button
⇒page 16 on the trip
counter. On vehicles which are equipped
with information display*, you can call up this infor-
mation in the following menu on
⇒page 24:
„
SETTINGS
„
Service Interval (Service)
„
ResetCaution
We recommend that you do not reset the Se
rvice Interval Display yourself otherwise
this can result in the service interval displa
y being incorrectly set, which may also result
in problems with operation of your vehicle.
Note
•
Never reset the display between service intervals otherwise this may result in
incorrect readouts.•
information is retained in the Service Inte
rval Display also after the battery of the
vehicle is disconnected.•
If the instrument cluster is exchanged after a repair, the correct values must be
entered in the counter for the Service Interval
Display. This work is carried out by a
specialist garage.•
The data displayed is the same after resetting the display with flexible service inter-
vals (QG1) using the reset button as that for a vehicle with fixed service intervals (QG2). We therefore recommend having the Service In
terval Display reset
only by an author-
ised Škoda Service Partner who is familiar with the procedure for resetting the display with a vehicle system tester.•
Please refer to the brochure Service schedule for extensive information about the
service intervals.
A3
A7
sgg.6.book Page 19 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
21
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Single-trip memory (memory 1) The single-trip memory collates the driving information from the moment the ignition is switched on until it is switched off. New data will also flow into the calculation of the current driving information if the trip is continued
within 2 hours
after switching off
the ignition. The memory will be is automatically erased, on the other hand, if the trip is interrupted for
more than 2 hours
.
Total-trip memory (memory 2) The total distance driven memory gathers da
ta from any number of individual jour-
neys up to a total of 99 hours and 59 minutes driving or 9.999 kilometres driven. The memory is deleted when either of these limits is reached and the calculation starts from anew. The total-trip memory will not, contrary to
the single-trip memory, be deleted after a
period of interr
uption of driving of 2 hours.
Note
All information in the memory
1 and
2 is erased if the battery of the vehicle is
disconnected.Operating with the buttons on the windshield wiper lever and on the multifunction steering wheel*Fig. 19 Multi-functional indicator: Control elementsThe rocker switch and the button are lo
cated in the grip of the window wiper
lever
⇒fig. 19
on the left. Switching over and resetting is performed with the hand-
wheel
⇒fig. 19
on the multifunction steering wheel.
Selecting the memory– After briefly pressing the button on
the windshield wiper lever or by briefly
pressing the button on the multifuncti
on steering wheel, you can select the
desired memory.
Selecting the functions with the he
lp of the windshield wiper lever
– Press the top or bottom rocker switch
for longer than 0.5 seconds. In this way,
call up in sequence the individual func
tions of the multi-functional indicator.
Selecting the functions with the
help of the multifunction steering
wheel– By pressing the button , you can call up
the menu of the multi-functional indi-
cator.
– Turn the handwheel upwards or downward
s. In this way, call up in sequence
the individual functions of th
e multi-functional indicator.
– Short-term pressing of the button allows to select the highlighted function.Setting function to zero– Select the memory you want.– Press the button or for more than 1 second. The following readouts of the selected memo
ry will be set to zero with the button
on the windshield wiper lever or with the button on the multifunction steering wheel:•
average fuel consumption,
•
distance driven,
•
average speed,
•
Driving time.
You can only operate the multi-functional in
dicator when the igniti
on is switched on.
After the ignition is switched on, the function displayed is the one which you last selected before switching off the ignition.
AA
AB
AD
AB
AD
AA
AC
AD
AD
AB
AD
AB
AD
sgg.6.book Page 21 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
23
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
If the memory is set to zero (after disco
nnecting the battery), th
e fuel consumption of
10 ltr./100 km is calculated for the range; afterwards the value is adapted accordingly to the style of driving.Distance drivenThe distance driven since the memory was last erased appears in the display ⇒ page 20. If you wish to measure the distance
driven of a particular time, you must
set the memory to zero at this moment in time by pressing the button on the wind- shield wiper lever
⇒page 21, fig. 19
or the handwheel on the multifunction
steering wheel*
⇒page 21, fig. 19
.
The maximum distance indicated in both switch positions is 9.999 km. The indicator is set back to null if this
period is exceeded.
Average speedThe average speed since the memory was last erased is shown in the display in km/hour
⇒page 20. If you wish to determine the average vehicle speed over a certain
period of time you must set the memory to zero at the start of the measurement using the button on the windshield wiper lever
⇒page 21, fig. 19
or with the handwheel
on the multifunction steering wheel*
⇒page 21, fig. 19
.
A zero appears in the display for the first 100 m you drive after erasing the memory.The indicated value will be updated every 5 seconds while you are driving.Current speed*The current speed which is identical to the display of the speedometer, is indicated on the display
⇒page 16, fig. 15
.
Oil temperatureThe oil temperature appears in the display when the ignition is switched on. If there is a fault, three lines are displayed instead of the temperature.
Warning against excessive speeds*Fig. 21 Warning against excessive speeds / mu
lti-functional indicator: Control elements
This function enables you to set a speed limit, e.g. if you drive in town. A text in the display is intended to draw your attention
to the fact that you have exceeded the set
speed limit.Warning against excessive speeds– Select the menu point
Speed warning --- km/h (warning at --- km/h).
.
– Drive e.°g at a speed of 50 km/h. – Press the button on the windshield wiper lever
⇒fig. 21
or the handwheel
on the multifunction steering wheel*
⇒page 21, fig. 19
. Speed warning 50 km/h
(warning at 50 km/h)
is displayed in the information display*
⇒fig. 21
. You can
increase or reduce this value with the
button on the windshield wiper lever or
by turning the handwheel on the multifunction steering wheel*.
– The value is stored by repeated pressing
of the button on the windshield wiper
lever or the handwheel on the multifunction steering wheel*.
If you now exceed th
e set speed limit,
Speed 50°km/h exceeded
will be shown on the
display. This message is indicated for as long as the speed is reduced below the set limit or switch off the message by pressing the button on the windshield wiper lever ⇒ fig. 21
or the handwheel on the mu
ltifunction steering wheel*
⇒page 21,
fig. 19
.
An audible signal sounds as an additional warning signal.The set speed limit remains stored even after switching off the ignition.
AB
AD
AB
AD
A2
AB
AD
AA
AD
AB
AD
AB
AD
sgg.6.book Page 23 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
25
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
– You can select the individual menus by
pressing the handwheel . After briefly
pressing the handwheel , th
e desired menu is indicated.
– After briefly pressing the button you can achieve a higher level, by pressing the
button for longer than 1 second, you can call up the
MAIN MENU
.
You can select the following information (d
epending on the equipment installed on
the vehicle):„
MFD (Onboard computer)
⇒page 20
„
Audio
*
„
Navigation
*
„
Phone
* ⇒page 129
„
Aux. Heating (auxiliary heating)
* ⇒page 105
„
Assistant
* ⇒page 55
„
Vehicle status
⇒page 26
„
Setup
⇒page 27
The menu point
Audio
is only then displayed when
the factory-fitted Radio* is
switched on. The menu point
Navigation
is only then displayed when the factory-fitted Navigation
system* is switched on. The menu point
Aux. Heating
is only then displayed, if
the vehicle is fitted with the
factory-fitted auxiliary heating*. The menu point
Assistant
is only then displayed, if the
vehicle is fitted with cornering
lights*.
Note
•
If warning messages are shown in the information display
⇒page 25
⇒page 26,
these messages can be confirmed with the bu
tton on the windshield wiper lever or
with the button on the multifunction steering wheel in order to call up the main menu.•
If you do not activate the information display at that moment, the menu shifts to
one level higher every 10 seconds.
•
The operation of the factory-fitted radio*
or the navigation system* is described in
separate operating instructions to be
found in the on-board literature.
Door, luggage compartment door and bonnet ajar warningThe door, luggage compartment and bonnet ajar
warning lights up if at least one door,
the luggage compartment or bonnet are not closed. The symbol indicates which door is still open or whether the luggage
compartment door or bonnet is
not closed

⇒ fig. 24
.
The symbol goes out as soon as the doors,
luggage compartment door and bonnet are
completely closed. A warning signal sounds if the car is driven at a speed of more than 6km/hour and if the engine or the luggage compartment door is open.
AD
AD
AC
AC
AB
AD
Fig. 24 Information display: Door warning
sgg.6.book Page 25 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
27
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Yellow symbols A yellow symbol signals a warning.Check the relevant function as soon as possible. The meaning of the yellow symbols: One
warning signal will sound if a yellow symbol appears.
If several operational faults
of priority 2 exist, the symbols appear one after the other
and are each illuminated for about 5 seconds.
Set-upYou can change certain settings by means
of the information display. The current
setting is shown on the information display in the respective menu at the top below the line
⇒fig. 28
.
You can select the following information (d
epending on the equipment installed on
the vehicle):•
Language
•
MFD Data (MFA DATA)
•
Convenience
•
Lights & Vision (Lights & Vision)
•
Time
•
Winter tyres
•
Units
•
Assistant (Assistant)
•
Alternative speed displayed (Second speed)
•
Tra v e l m o d e
•
Service Interval (Service)
•
Factory Setting
•
Back
After selecting the menu point
Back
you will reach one level higher in the menu.

Check engine oil level, engine oil sensor faulty
⇒ page 205

Brake pad worn
⇒page 36
Fig. 27 Information display: Brake pad worn
Fig. 28 Setting the clock
sgg.6.book Page 27 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
29
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Service Here you can have the kilometers still to
be driven and the days until the following
service interval shown and the Service Interval Display reset.
Factory Setting After selecting the menu point
Factory Setting
the factory setting of the information
display is established again.
Warning lightsOverview The warning lights indicate certain functions or faults.
Fig. 29 Instrument cluster with warning lights

Turn signal lights (to the left)
⇒page 31

Turn signal lights (to the right)
⇒page 31

Fog lights*
⇒page 31

Main beam light
⇒page 31

Low beam light
⇒page 31

Rear fog light
⇒page 31

Speed regulating system*
⇒page 31
sgg.6.book Page 29 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
31
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Turn signal system

Either the left
 or right
 indicator light flashes depending on the position of the turn
signal lever. The indicator light flashes at twice its normal rate if a turn signal light fails. This does not apply when towing a trailer. Switching off the hazard warning light system
is switched on will cause all of the turn
signal lights as well as both indicator lights to flash. Further information about the turn signal system
⇒page 59.
Fog lights*

The warning light
 comes on when the fog lights are operating
⇒page 56.
Main beam

The indicator light
 comes on when the main beam is selected or also when the
headlight flasher is operated. Further information about the main beam
⇒page 59.
Low beam

The warning light
 comes on when low beam is selected
⇒page 53.
Rear fog light

The warning light
 comes on when the rear fog lights are operating
⇒page 57.
Cruise control system*

The warning light
 lights up, when operating the speed regulating system.
Bulb failure

The warning light
 comes on if a bulb is faulty:
•
up to 2 seconds after the ignition is switched on;
•
when switching on the defective light bulb.
The following text e.g will be displayed in the information display*:
Check front right dipped beam!
The rear side lights and the licence plate lighting require several light bulbs. The indi- cator light
 only lights up if all light bulbs of
the licence plate lighting or the parking
light (in one rear light unit) are defective.
Check regularly the function of the light
bulbs.Diesel particle filter*

(diesel engine)
If the warning light

comes on, this means that soot
has accumulated in the diesel
particle filter because of the frequent short distances. In order to clean the diesel particle filter, the vehicle should be driven at an even speed of at least 60 km/h at engine speeds of 1
800 - 2 500 rpm for at least 15 minutes or until
the warning light goes out with the 4th or
5th gear engaged (automatic gearbox: posi-
tion S) when the traffic situation permits it. This increases the exhaust temperature and the soot deposited in the diesel particle filter is burnt. Always pay attention to the valid speed limits
⇒
.
The warning light

goes out after the successful cleaning of the diesel particle filter.
If the filter is not properly
cleaned, the warning light

does not go out and the
warning light
 begins to flash. In the in
formation display* appears
Diesel-particle
Owner's manual
. Afterwards the engine control unit shifts the engine into the emer-
gency mode, which only has a reduced power
output. After switchin
g the ignition off
and on again the warning light
 comes on.
Have the vehicle inspected without
delay by your specialist garage.
sgg.6.book Page 31 Thursday, September 24, 2009 2:32 PM