Communication
133
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
DialogueThe period, in which the telephone system is ready to receive voice commands and carry out the voice commands, is called DI
ALOGUE. The system gives audible feedback
and guides you if necessary through the relevant functions. You can start or end the dialogue at
any time by pressing the PTT button
on the
adapter*
⇒page 132, fig. 129
or on the multifunction steering wheel*
⇒page 131 or
end it with the voice command
CANCEL
.
The dialogue is always automatically ended after carrying out an operation, e.g. after erasing the name from the phonebook. When receiving an incoming call, the dialog
ue is immediately in
terrupted and you can
accept the call by pressing the button°
on the multifunction steering wheel*
⇒ page 131 or by pressing the button for re
ceiving a call directly on your telephone.
If a voice command is not detected, the system answers with “
Sorry?
” and a new entry
can be performed. After the 2nd error the system repeats the aid. After the 3rd error the answer “
Cancel
” is given and the dialogue is ended.
Optimum understanding of the voice commands depends on the following factors:•
Speak with a normal tone of voice withou
t intonation and excessive voice pauses.
•
Avoid insufficient articulation.
•
Close the doors, windows and sliding roof, in order to reduce or stop disturbing
exterior noise.•
It is recommended to speak louder at higher speeds, so that the tone of your voice
is louder than the increased surrounding noise.•
During the dialogue avoid additional nois
e in the vehicle, e.g. simultaneously
talking occupants.•
Do not speak, if the syst
em makes an announcement.
•
The microphone for voice control is direct
ed to the driver and front passenger.
Therefore the driver and the front passenger can operate the equipment.
Voice commandsThe digits
zero to nine
are permitted. The system dete
cts no continuous digit combi-
nations such as twenty-three, but only indi
vidually spoken digits (two, three). After
each order of digits (separation through br
ief voice pause) the detected digits are
repeated. The telephone number can be entered as an
interconnected spoken row of digits
(complete number), in the form of order of
digits (separation through a brief voice
pause) or through individually
spoken digits. After each order of digits (separation
through brief voice pause) the
detected digits are repeated.
If you enter more than 20 di
gits, the system announces: “
The number is too long
”.
Additionally for international calls a
Plus (+)
has to be entered in front of the 20 digits.
The voice control is possible in the following languages:
Czech, English, German, French, Italian and Spanish.Voice commands
Activity
ENTER PIN/PIN CODE
After this command the PIN code of the mobile phone can be entered
⇒page 134.
DIAL NUMBER
After this command a phone number can be entered which establishes a connection to the requested party.
REDIAL
After this command the last selected telephone number is selected again.
sgg.6.book Page 133 Thursday, September 24, 2009 2:32 PM
Intelligent Technology
169
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
If there is a fault in the power steering, the warning light
or lights up in the instru-
ment cluster
⇒page 32.
WARNING
Contact your specialist
garage if the power steering is defective.
Tyre inflation pressu
re-control system*
The tyre inflation pressure-control system compares with the aid of the ABS sensors the speed and also the rolling circumference of the individual wheels. If the rolling circumference of a wheel is changed, the warning light
lights up in the instrument
cluster
⇒page 35 and an audible signal sounds.
The rolling circumference of the tyre
can change if:•
the tyre inflation pressure is too low,
•
the structure of the tyre is damaged,
•
the vehicle is loaded on one side,
•
the wheels of an axle are loaded heavily (e.g. when towing a trailer or when driving
uphill or downhill),•
snow chains are mounted,
•
the temporary spare wheel is mounted,
•
one wheel per axle was changed.
Basic setting of tyre inflation pressure-control system After changing the tyre inflation pressures or after changing one or several wheels, the position of a wheel on the vehicle (e.g. ex
changing the wheels between the axles) or
when the warning light lights up while drivin
g, a basic setting of the system must be
carried out as follows.•
Inflate all tyres to the specified inflation pressure
⇒page 215.
•
Switch on the ignition.
•
Press button
⇒fig. 156
for more than 2 seconds. While pressing the button,
the warning light
lights up. At the same time the memory of the system is erased
and the new calibration is started, which is confirmed with an audible signal and then the warning light
goes out.
•
If the warning light
does not go out after the basic
setting, there is a fault in the
system. Have the vehicle inspected by your nearest specialist garage. Warning light
lights up
If the tyre inflation pressure of at least one
wheel is insufficiently inflated in comparison
to the stored basic va
lue, the warning light
⇒
lights up.
Warning light
flashes
If the warning light flashes, there is a system fault. Have the vehicle inspected by your nearest specialist garage.
WARNING
•
When the warning light
lights up, immediately reduce the speed and
avoid sudden steering and brake manoeuvr
es. Please stop the vehicle without
delay at the nearest possible stop and in
spect the tyres and their inflation pres-
sures.•
The driver is responsible for the correc
t tyre inflation pressures. For this
reason, the tyre inflation pressu
res must be checked regularly.
•
Under certain circumstances (e.g. sporty style of driving, wintry or unpaved
roads) the warning light
can be delayed or does not light up at all.
•
The tyre inflation pressure-control system does not take away the respon-
sability from the driver for the
correct tyre inflation pressure.
Fig. 156 Button for setting the tyre infla- tion pressure control value
sgg.6.book Page 169 Thursday, September 24, 2009 2:32 PM
