2009 SKODA SUPERB stop start

General information
2General informationEquipment overview
Switching on/off
: Rotary/push knob for switching the navigation
system on/off (press) and volume control (turn) Selector key
for selecting the corresponding menu:
−
– changes over into radio mode and changes the
frequency range when in the radio mode. −
– changes over to the last pl
ayed media source or selects
a new media source. −
– Phone function – Muting
of the current audio source.
−
– TIM function (Traffic Information Memory) recorded traffic
announcements can be replayed
. After entering up to two
different TIM recording times in
SETUP
menu, a recording of the
traffic announcements is also possible if the unit is switched off. −
– Switch the traffic information function (Traffic Program) on
or off or interrupt the currently received traffic announcement. −
– enables setting-up the individual fields.
and
: The backwards/forwards keys operate the “active” audio
source. − RADIO-Mode
– for the selection of the stations from the memory
list. − MEDIA-Mode
– for the selection of th
e previous or following
track. CD-case Touchscreen (Touch-screen):
Fields circled in colour on the display
are presently “active” and are op
erated by touching the display.
Eject key
– press briefly to move an inserted CD into the posi-
tion ready for removal. – opens the sound and volume settings menu. Setting up button
− RADIO mode
– turn for manual station adjustment; press briefly
to start or stop the automatic play (Scan). − MEDIA mode
– turn to change track; press briefly to start or stop
the automatic play (Scan). Memory card case
: SD memory cards (“Secure Digital Memory
Cards”), SDHC (“Secure Digital
High Capacity Card”) and MMC
(“Multimedia Cards”) measuring 32 mm x 24 mm x 2.1 mm and with a capacity of up to 32 GB are avai
lable. The case for the memory card
is located under the display.
Explanation of symbols * items of equipment which are marked in such a way are only installed as standard on certain models or are supplied as special equipment. End of a section. The section is continued on the next page.
Note
This Owner's Manual describes the range of fu
nctions at the time of going to press.
The illustrations can differ in minor
details from the version of your unit.
Important informationWarrantyThe equipment warranty terms and conditions also apply for new vehicles. After the expiration of the warranty, a piec
e of equipment in need of repair will be
replaced with a reconditioned, original item with spare part warranty. It is, however, a precondition that the housing has
not been damaged and no unauthorised
attempts have been made
to carry out repairs.
A1A2
RADIOMEDIAPHONETIMTPSETUP
A3


A4A5A6
/
A7

A8
A9
s1ok.1a.book Page 2 Monday, March 30, 2009 3:29 PM

Basic setting
8Irrespective of which radio station is heard,
an additional receiver part in the unit
ensures that a traffic information station can
always be received as long as the traffic
information function is switched on. The readiness of the traffic information function is displayed by “
TP” at the top right
in the display. If no traffic information st
ation can be received becaus
e, for example, radio recep-
tion is interrupted in general, “
No TP
” will be displayed instead of “
TP”. Remember
that car parks, tunnels, high
buildings or mountains can interrupt the radio signal
up to the total loss of reception. Incoming traffic announcement When a traffic announcemen
t is being received, a pop-up window will open.
If you wish to interrupt the transmission
of the traffic announcement, press on the
function key in the pop-up window
Traffic announcement
. The traffic infor-
mation function remains available and a
following traffic anno
uncement is made
again while the audio mode is in op
eration. Pressing the function key
will switch off the traffic information function permanently.
Traffic information memoryAutomatic recording of traffic reports If the traffic information function is switched on and a traffic information station is received, the incoming
traffic reports will be recorded
, as long as the ignition is
switched on. This way you are
informed at any time of the current traffic situation,
even if you have your radio switched
off for a lengthy period while driving.
If the vehicle is not in use (i
gnition off) while a traffic information station is received
and the traffic information function is sw
itched on, incoming
traffic reports from
this station are recorded for two hours. When switching the ignition off the current traffic information station is displayed for about five seconds, from which the next 65 minutes of traffic reports will be recorded. During this display of five seco
nds, you can select another traffic infor-
mation station using the arrow keys on the unit, which will be recorded.
If, when the vehicle is not in use, the rece
ption of the set traffic information station
is too poor because of external influences
, it will automatically search for another
traffic information station. A maximum of nine traffic a
nnouncements with a total length of up to four minutes
can be recorded. The oldest traffic report
will always be overwritten if the memory
is full. TIM recording times You also have the possibility to set two TIM recording times, to which the unit will also record traffic reports when the vehicl
e is not in use. Then the radio starts
according to the set TIM recording time with
the recording of all the incoming traffic
reports on the set traffic information station. For example, when you drive your vehicle to
work everyday at a certain time, only
enter the approximate start time. The radio starts with the recording at the set start time and ends the recording 65 minutes afterwards. In this way, before you begin your journey, you can retrieve the last traf
fic reports and tune into the current traffic
situation of the distance to be driven.
Note
•
In case of a message of over four minu
tes long, the beginni
ng is overwritten.
•
If the vehicle has not been used for mo
re than three days, no further traffic
reports are recorded, in order to stop
the vehicle battery from running down.
Playing traffic reports– Press on the button , in order to listen to the stored traffic
reports. The play function starts wi
th the last recorded traffic report
and runs through to the oldest recorded traffic report.
– Press on the button , in order to switch to the beginning of the
currently heard traffic report.
– In order to skip a traffic report, press on the button .
Cancel
TP deactivated
INFO

s1ok.1a.book Page 8 Monday, March 30, 2009 3:29 PM

Basic setting
9
– You can interrupt the play function by pressing the button . The
button changes to . Pressing the button will continue the play function from the last point.
Selector key MEDIAThe main MEDIA menuCalling up the main MEDIA
menu and changing media source
– By pressing the button the play
function of the last played
media source will continue.
If audio sources are currently selectable
at the unit, use the range selector key
to change between the last audio sources.
If a previously played media source is se
lected again, play will continue from the
last played part. If an audio source cannot be selected at
the present time because, for example, no
data carrier has been inserted (e.g no
memory card), the function key will be
displayed with a grey background. Buttons on the unit for controlling the current audio sources – pressing this briefly changes over to
the beginning of the current title or
chapter, repeated pressing changes over to
the beginning of the previous title or
chapter. – briefly pressing this changes over to the next title or chapter.It is also possible to change tracks in the menu of the currently played audio source using the control button . Function keys for controlling the current audio sources
– pressing this briefly changes over to
the beginning of the current title or
chapter, repeated pressing changes over to
the beginning of the previous title or
chapter.
– briefly pressing this changes over to the next title or chapter.
– Pause: The play function is stoppe
d in the current position - the symbol
changes to , – pressing will continue
the play function in this position.
Selectable audio sources in the menu MEDIA
– changes over to the last played CD from the CD changer.
– changes over to an inserted memory card. – changes over to an additionally co
nnected external audio source *. Oper-
ating an externally connected audio source is possible with certain restrictions and depends largely on the type of the connection. Additional function keys in the main menu MEDIA
– starts the automatic play
Scan
. If is already displayed, the auto-
matic play has started - press
the function key to terminate.
– starts the random play function
Mix
. If is already displayed, the
random play function has started - press the function key to terminate.
– opens the pop-up window for switch
ing on the repeat function. In addi-
tion, it is determined if only the cu
rrent or the current or for the MP3
operation of the current the current is repeated.
– opens the title list of the current media source in order to choose
another title or another media source.Inserting or ejecting a CDInserting the CD –Press the button . – Choose the location .... for stor
ing the CD in the internal CD
changer. Wait until “
Please insert CD
” is displayed.
– Push a CD with the written side facing up as far as possible into the CD
case until it is automatically drawn in. The play function will start auto-matically.



MEDIA
MEDIA
A1




CDSD cardAUXScan
 Scan
Mix
Mix
Repeat
Tra c k
CD
Folder
Playlist
Selection
/1
6
s1ok.1a.book Page 9 Monday, March 30, 2009 3:29 PM