2009 SKODA OCTAVIA lights

Lights and Visibility
71
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
The headlight washer nozzles are moved forward out of the bumper by the water pressure for cleaning the headlights. You should remove stubborn dirt (such
as insect residues) from the headlight
lenses at regular intervals, for example when refuelling. Please refer to the following guidelines
⇒page 214, “The headlight lenses”.
You should remove any snow from the fixt
ures of the washer nozzles and clear ice
in winter with a de-icing spray in order to
ensure proper operation of the cleaning
system.Replacing wiper blades fo
r the windscreen wipers
One cannot fold out the wiper arms in the rest position from the wind- screen. Before replacing the wiper
arms you must put them into the
service position. Service position for changing wiper blades – Close the bonnet. – Switch the ignition on and then again off. – Then press the windscreen wiper lever in the position
⇒
page 69,
fig. 68
within 20 seconds - the wiper ar
ms move into the service posi-
tion.
Taking off the wiper blade – Fold windscreen wiper arm out from
the windscreen and position the
wiper blade at right angles to the wiper arm
⇒
.
– Take off the wiper blade in direction of arrow
⇒
fig. 69
⇒
.
Attaching a wiper blade – Push the new wiper blade over the wiper arm and turn the wiper blade
into the vertical position.
– Check whether the wiper blade is correctly attached.– Fold the windscreen wiper arms onto the window and switch on the
ignition. By pressing the window wi
per lever into the sprung position
⇒
fig. 69
or when driving at a speed greater than 4 km/h, the wind-
screen wiper arms move back into the rest position.
Wiper blades in proper condition are esse
ntial to obtain good visibility. Wiper
blades should not be allowed to become
dirtied by dust, insect remains and
preserving wax. Juddering or smearing of the wiper blades
could then be due to wax residues left
on the windscreen by vehicle washing in
automatic vehicle wash systems. It is
therefore important to
degrease
the lips of the wiper blades after every pass
through an
automatic vehicle wash system
.
WARNING
•
The ignition must not be switched on if the front windscreen wiper arms
are folded out. The wiper blades would move back into their rest position and while doing so damage th
e paintwork of the bonnet.
•
If the windscreen wipers are handled carelessly, there is a risk of damage
to the windscreen.•
You should clean the wiper blades regularly with a windscreen cleaner in
order to avoid any smears. Clean a wiper blade with a sponge or cloth if it is very dirty, for example from insect residues.
Fig. 69 Wiper blade for the windscreen wiper
A4
A4
se0.1.book Page 71 Friday, April 10, 2009 3:19 PM

Lights and Visibility
72
•
Replace the wiper blades once or twice a year for safety reasons. These
can be bought from an authorised Škoda Service Partner.Replacing the wiper blade on
the rear window wiper
Taking off the wiper blade – Fold windscreen wiper arm out from the windscreen and position the
wiper blade at right angles to the wiper arm
⇒
fig. 70
.
– Hold the window wiper arm at the top end with one hand. – With the other hand unlock the locking button in the direction of
arrow and remove the wiper blade.
Attaching a wiper blade – Position the wiper blade onto the wiper arm and lock the locking
button .
– Check whether the wiper bl
ade is correctly attached.
The same remarks apply here as for
⇒page 71.
Rear-view mirrorManual dimming interior rear-view mirrorBasic setting – Pull the lever on the bottom edge of the mirror forward. Dimming mirror – Pull the lever on the bottom edge of the mirror back.Automatic dimming interior mirror*Switching on the automatic dimming– Press the button - the warning light lights up
⇒
fig. 71
.
Switching off the automatic dimming – Press again the button - the warning light goes out .If the automatic dimming is switched on, the mirror dims
automatically

depending on the light striking the mirror from the rear. The mirror has no lever on the bottom edge of the mirror. When the
interior lights are switched on or the
reverse gear is engaged, the mirror alwa
ys moves back into the basic position.
WARNING (continued)
Fig. 70 Wiper blade for rear windowAA
AA
Fig. 71 Automatic dimming interior mirror
AB
AA
AB
AA
se0.1.book Page 72 Friday, April 10, 2009 3:19 PM

Lights and Visibility
73
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Note
•
Automatic mirror dimming operates only pr
operly if the sun screen* for the rear
window in the housing on the luggage comp
artment cover is not in use or the light
striking the interior rear-view mirror is not affected by other objects.•
Do not affix any stickers in front of the light sensor, so that you do not impair the
automatic dimming function or put it out of operation.•
If you switch off the automatic dimming interior rear-view mirror, also the exte-
rior mirror dimming is switched off.Exterior mirror You can adjust the exterior mirrors electrically*.The exterior mirror heater only oper
ates when the engine is running and
up to an outside temperature of +20 °C. Heating of the external mirror – Turn the rotary knob to position
 ⇒
fig. 72
.
Adjusting left and right exterior mirrors simultaneously – Turn the rotary knob to position
. The movement of the mirror surface
is identical to the movement of the rotary knob.
Adjusting the right-hand exterior mirror – Turn the rotary knob to position
. The movement of the mirror
surface is identical to the movement of the rotary knob.
Switching off operating control – Turn the rotary knob to position
.
Folding in both exterior mirrors* – Turn the rotary knob to position

.
Lowerable exterior mirror* with the aid of the key for remote control – If all the windows are closed, press the unlock button on the radio
remote control
⇒
page 50, fig. 47
for approx. 2 seconds.
Tilting surface of front pa
ssenger exterior mirror*
When the rotary knob is in position
 ⇒fig. 72
and the reverse gear is engaged, the
s ur fa ce o f t h e m i rro r t i l ts d o w n s l i g h t l y. T h i s p ro v i d e s a n a i d i n s e e i n g th e ke r b o f t h e pavement when parking the car. The mirror returns into its initial position, after the rotary knob is moved out of the position
 and put into another position or if
the speed is more than 15 km/h.
Memory for exterior mirrors* On vehicles fitted with a memory for the driver seat, the relevant setting of the exte- rior mirror is also stored automatica
lly when the seat position is stored
⇒page 76.
WARNING
•
Convex (curved outward) or spherical (differently curved) exterior
mirrors increase the vision field. Th
ey do, however, make objects appear
smaller in the mirror. These mirrors are
only of limited use, therefore, for
estimating distances to the following vehicles.•
Use whenever possible the interior rear mirror, for estimating the
distances to the following vehicles.
Fig. 72 Inner part of door: Rotary knob
A3
se0.1.book Page 73 Friday, April 10, 2009 3:19 PM

Lights and Visibility
74
Note
•
If the exterior mirrors are folded in using the remote control* of the vehicle key,
these are folded back into the driving position after switching on the ignition.•
If the exterior mirrors are folded in using the rotary knob
⇒page 73, fig. 72
,
they can only be folded back into the
driving position using the rotary knob.
•
If the exterior mirrors were folded in
using the remote control* of the vehicle
key and if the rotary knob was in the fold
-in position before switching on the igni-
tion, the mirrors remain in the fold-in position the next time the ignition is switched on. Folding back into the driving position
is performed by actuating the rotary knob
in a different position fr
om the fold-in position.
•
Do not touch the surfaces of the exterior mirrors if the exterior mirror heater is
switched on.•
You can set the exterior mirr
ors by hand, if the power setting function fails at any
time by pressing on the edge of the mirror surface.•
Contact your specialist garage if a fault exists with the power setting of the exte-
rior mirrors.Automatic dimming exterior mirror*The exterior mirrors are dimmed together with the interior mirror. If the automatic dimming is switched on, the mirror dims
automatically
depending on the light
striking the mirror from the rear. When the interior lights are switched on or
the reverse gear is engaged, the mirror
always moves back into the
basic position (not dimmed).
Note
•
Automatic mirror dimming operates only pr
operly if the sun screen* for the rear
window is not in use or the li
ght striking the rear of the interior rear-view mirror is
not affected by other objects.•
Do not affix any stickers in front of the li
ght sensor, so that you do not impair the
automatic dimming function or put it out of operation.
•
If you switch off the automatic dimming interior rear-view mirror, also the exte-
rior mirror dimming is switched off.
se0.1.book Page 74 Friday, April 10, 2009 3:19 PM

Seats and Stowage
83
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Rear seat armrest*– You can fold down the armrest at
the loop to enhance occupant
comfort
⇒
page 83, fig. 84
.
Seat heaters*
You can electrically heat the seat ba
ckrests and the surfaces of the front
seats and the two outer rear seats. – You can switch on and regulate the
seat heating of the driver or front
passenger seat by pressing the surfac
e of the regulator at the point at
which the symbol is located
 ⇒
fig. 85
.
– You can switch on and adjust the heat
ers of the left or right rear seats
by pressing the regulator
 ⇒
fig. 86
.
– With one press, you can switch the
heating to highest intensity which
is indicated by the lighting up of the three warning lights in the switch.
– With repeated pressing of the switch, the intensity of the heating is
down-regulated up to the switch-off. The intensity of the heating is indicated by the number of illuminated warning lights in the switch.
WARNING
If you have a subdued pain and/or te
mperature sensitivity, e.g. through
medication, paralysis or because of ch
ronic illness (e.g. diabetes), we
recommend not to use the seat heating. This can lead to burns on the back, the posterior and the
legs which are difficult to he
al. If the seat heating is
used, we recommend to make regular breaks in your journey when driving long distances, so that in specific cases as mentioned above the body can
Fig. 84 Rear seats: ArmrestFig. 85 Dash panel: Regu- lator for front seat heating
Fig. 86 Centre console at rear: Regulator for heating the rear seats
se0.1.book Page 83 Friday, April 10, 2009 3:19 PM

Heating and air conditioning system
111
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Recirculated air mode In recirculated air mode air is sucked
out of the interior of the vehicle
and then fed back into the interior.Recirculated air mode prevents polluted air outside the vehicle from getting into the vehicle, for example when driving through a tunnel or when standing in a traffic jam. Switching recirculated air mode on – Press the button - the warning light lights up in the button
⇒
page 109, fig. 139
.
Switching recirculated air mode off – Press again the button - the warning light in the button goes out.The recirculated air mode is switched off au
tomatically if the air distribution control
is in position
 ⇒page 109, fig. 139
. You can also switch recirculated air mode
on again from this setting by repeatedly pressing button .
WARNING
You should not leave recirculated air mode on over a longer period of time, as “stale” air may result in fatigue in
the driver and occupants, divert your
attention and also cause the windows to mist up. The risk of having an acci- dent increases. Switch recirculated
air mode off as so
on as the windows
begin misting up.
Climatic* (semi-automatic air conditioning system)Description The Climatic is a combined cooling and heating system. It makes it possible to optimally control the air temperature at any season of the year.Description of the Climatic It is important for your safety and for your driving comfort that the Climatic is oper- ating properly. The cooling only operates if button
⇒page 112, fig. 140
is pressed, and the
following conditions are met:•
engine running,
•
outside temperature above approx. +2°C and
•
blower switch switched
on (positions 1 to 4).
If the cooling system is switched on, th
e temperature and air humidity drops in the
vehicle. The wellbeing of the occupants of
the car is enhanced as a result of this
particularly at high outside temperatur
es and a high air humidity. The system
prevents the windows misting up during the cold season of the year. The heating effect is dependent upon th
e coolant temperature, thus full heat
output only occurs when the engine has reached its operating temperature. It is possible to briefly activate recirc
ulated air mode in order to enhance the
cooling effect
⇒
.
Air at a temperature of about 5°C may flow
out of the vents under certain circum-
stances when the cooling system is operating. Lengthy and uneven distribution of the air flow out of the vents and large differences in temperature, for example when getting out of the vehicle, can resu
lt in chills in sensitive persons.
The air inlet in front of the windscreen must
be free of ice, snow or leaves in order
to ensure that the heating and cooling systems operate properly. After switching on the cooling
Condensation
from the evaporator of the air condi-
tioning may drip down and form a puddle be
low the vehicle. This is quite normal
and not an indication of a leak!


AC

AC
A1
se0.1.book Page 111 Frida
y, April 10, 2009 3:19 PM

Heating and air conditioning system
113
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
switching cooling on and off – Press the button
⇒
page 112, fig. 140
. The warning light lights
up in the button.
– When you again press the switch , the cooling system is switched
off. The warning light in the button goes out.
Rear window heater – Press button . Further information
⇒
page 67, “Rear window
heater”.
Auxiliary heating (auxiliary heating) – Press the button in order to directly switch on/off the auxiliary
heating (auxiliary heating and ventilation. Further information ⇒
page 119, “Auxiliary heating (auxil
iary heating and ventilation)*”.
The set temperature will be automatica
lly maintained other than when the
control dial is on the extreme
right or extreme left position:
•
Extreme right position - full heating,
•
Extreme left position - full cooling,
•
The blower should aways be on to prevent the windows from misting up.Note
•
The whole heat output will be needed
to unfrost the windscreen and side
windows. No warm air will be fed to the footwell. This can lead to restriction of the heating comfort.•
The used air streams out through the air removal openings in the luggage
compartment.•
If the cooling system has not been switched on for a lengthy period, odours may
be produced at the evaporator because of
deposits. Switch the cooling system on
at least once a month for approximately 5 mi
nutes at the highest blower stage - also
during the cold season of the year - in
order to remove such odours. Also open a
window for a short time.•
Please refer to the information regarding recirculated air mode
⇒page 114.
Set ClimaticRecommended settings of Climatic controls for the respective operating modes:
AC
A1
AC

A2A3
Set-up
Setting of the control dial
Button
Air outlet vents 3
Defrosting the windscreen and side windows
recommended
22°C
3

switched off
do not switch on
open and align with the side
window
Free windscreen and side win- dows from mist
desired tempera-
ture
2

switched on
do not switch on
open and align with the side
window
the fastest heating
recommended
22°C
2

switched off
briefly switched on
open
AA
AB
AC
A1
A4
se0.1.book Page 113 Frida
y, April 10, 2009 3:19 PM

Heating and air conditioning system
114
Recirculated air mode In recirculated air mode air is sucked
out of the interior of the vehicle
and then fed back into the interior.Recirculated air mode prevents polluted air outside the vehicle from getting into the vehicle, for example when driving through a tunnel or when standing in a traffic jam. Switching recirculated air mode on – Press the button
⇒
page 112, fig. 140
the warning light lights
up in the button.
Switching recirculated air mode off – Press again the button - the warning light in the button goes out.The recirculated air mode is switched off au
tomatically if the air distribution control
is in position
 ⇒page 112, fig. 140
. You can also switch recirculated air mode
on again from this setting by
repeatedly pressing button .
WARNING
You should not leave recirculated air mode on over a longer period of time, as “stale” air may result in fatigue in the driver and occupants, divert your attention and also cause the windows to mist up. The risk of having an acci-dent increases. Switch recirculated air mode off as soon as the windows begin misting up.Using the air conditioning system economicallyThe compressor on the air co
nditioning system uses po
wer from the engine when
in cooling mode which will effect the fuel consumption. It recommended to open the windows or the doors of a vehicle for which the inte- rior has been strongly heated through the ef
fect of direct sunlight in order to allow
the heated air to escape. The cooling system should not be switched on while travelling when the window is open. The desired interior temperature can also be achieved without switching in the cooling system just by switching to fresh air mode.
comfortable heating
desired tempera-
ture
2 or 3

 
switched off
do not switch on
open
the fastest cooling
recommended
22°C
briefly 4, then
2or 3

switched on
briefly switched on
open
optimal cooling
desired tempera-
ture
1, 2 or 3

switched on
do not switch on
open and align to the roof
Fresh air mode - ventilation
up to the stop towards the left
desired position

switched off
do not switch on
open
Set-up
Setting of the control dial
Button
Air outlet vents 3
AA
AB
AC
A1
A4

A4
AC

se0.1.book Page 114 Frida
y, April 10, 2009 3:19 PM