2009 SKODA OCTAVIA lock

Lights and Visibility
66
Reading lights* – Press on one of the switches in order to switch the right or left
reading light on or off.
The interior light comes on as soon as you unlock the car or open a door or when the ignition key has been removed. The li
ght goes out again about 30 seconds after
all the doors have been closed. The interior
lighting is switched off when you lock
the car or switch the ignition on. This on
ly applies when the switch for the corre-
sponding interior lights is stan
ding n the door contact setting.
The interior lighting goes off after about
10 minutes when a door has been left open
in order to avoid discharging the battery of the vehicle. If the switch is in the position
 (permanent lights), the interior lighting goes off at
the latest after 10 minutes in order to avoid discharging the battery of the vehicle.
Note
We recommend having these bulbs re
placed by a specialist garage.
Lighting of the storage compartment on front passenger side*– When opening the flap of the st
orage compartment on the front
passenger side the lighting in the storage compartment comes on.
– The light switches on automatically
when the parking light is switched
on and goes out when the flap is closed.
Front door warning light*The warning light is located in the door trim panel below
⇒fig. 62
.
The warning light goes on every time the door is opened. The light goes out about 10 minutes after opening the d
oor in order to avoid discharging the battery of the
vehicle. There is a reflector installed on some vehicles instead of the warning light.Luggage compartment light*The lighting comes on automatically when
the boot lid is opened. The luggage
compartment lighting will switch off agai
n automatically if the boot lid remains
open for more than about 30 minutes.Entry lighting*The lighting is positioned on the bottom edge of the exterior mirror. The light beam is directed towards the entry area of the front door.The light comes on after the doors have been
locked or on opening the boot lid. The
light goes out after switching on the ignition
or up to 30 seconds after closing all the
doors, the bonnet and the boot lid.
AB
Fig. 62 Front door: Warning light
se0.1.book Page 66 Friday, April 10, 2009 3:19 PM

Lights and Visibility
68
The vanity mirrors* in the sun visors are
provided with covers. Push the cover in
direction of arrow . On vehicles which are equipped with do
uble sun visor*, you can also unfold the
auxiliary visor after swivelling the sun visor
⇒page 67, fig. 65
.
WARNING
The sun visors must not be swivelled to the side windows into the deploy- ment area of the head airbags if any ob
jects, such as ball-point pens etc. are
attached to them. This might result in injuries to the occupants if the head airbag is deployed.Sun screen*
The sun screen is located in a housing on the luggage compartment cover. If required, you can remove the housing with the sun screen from the luggage compartment cover. Pulling out – Pull the sun screen at the loop and hang it in the brackets
⇒
fig. 66
.
Folding – Take the sun screen out of the brackets and hold it at the loop
so that it can roll up slowly and
without damage into the housing on
the luggage compartment cover.
Removing – Unhook the fastening elements from the luggage compartment cover
.
– Roll up the sun screen again into the housing on the luggage compart-
ment cover.
– Press the locking button in the direction of arrow and take out the
sun screen in the direction or arrow
⇒
fig. 67
.
A2
Fig. 66 Unroll the sun screen
Fig. 67 Remove the sun screen
AA
AB
AB
AA
AC
A1
A2
se0.1.book Page 68 Friday, April 10, 2009 3:19 PM

Lights and Visibility
72
•
Replace the wiper blades once or twice a year for safety reasons. These
can be bought from an authorised Škoda Service Partner.Replacing the wiper blade on
the rear window wiper
Taking off the wiper blade – Fold windscreen wiper arm out from the windscreen and position the
wiper blade at right angles to the wiper arm
⇒
fig. 70
.
– Hold the window wiper arm at the top end with one hand. – With the other hand unlock the locking button in the direction of
arrow and remove the wiper blade.
Attaching a wiper blade – Position the wiper blade onto the wiper arm and lock the locking
button .
– Check whether the wiper bl
ade is correctly attached.
The same remarks apply here as for
⇒page 71.
Rear-view mirrorManual dimming interior rear-view mirrorBasic setting – Pull the lever on the bottom edge of the mirror forward. Dimming mirror – Pull the lever on the bottom edge of the mirror back.Automatic dimming interior mirror*Switching on the automatic dimming– Press the button - the warning light lights up
⇒
fig. 71
.
Switching off the automatic dimming – Press again the button - the warning light goes out .If the automatic dimming is switched on, the mirror dims
automatically

depending on the light striking the mirror from the rear. The mirror has no lever on the bottom edge of the mirror. When the
interior lights are switched on or the
reverse gear is engaged, the mirror alwa
ys moves back into the basic position.
WARNING (continued)
Fig. 70 Wiper blade for rear windowAA
AA
Fig. 71 Automatic dimming interior mirror
AB
AA
AB
AA
se0.1.book Page 72 Friday, April 10, 2009 3:19 PM

Lights and Visibility
73
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Note
•
Automatic mirror dimming operates only pr
operly if the sun screen* for the rear
window in the housing on the luggage comp
artment cover is not in use or the light
striking the interior rear-view mirror is not affected by other objects.•
Do not affix any stickers in front of the light sensor, so that you do not impair the
automatic dimming function or put it out of operation.•
If you switch off the automatic dimming interior rear-view mirror, also the exte-
rior mirror dimming is switched off.Exterior mirror You can adjust the exterior mirrors electrically*.The exterior mirror heater only oper
ates when the engine is running and
up to an outside temperature of +20 °C. Heating of the external mirror – Turn the rotary knob to position
 ⇒
fig. 72
.
Adjusting left and right exterior mirrors simultaneously – Turn the rotary knob to position
. The movement of the mirror surface
is identical to the movement of the rotary knob.
Adjusting the right-hand exterior mirror – Turn the rotary knob to position
. The movement of the mirror
surface is identical to the movement of the rotary knob.
Switching off operating control – Turn the rotary knob to position
.
Folding in both exterior mirrors* – Turn the rotary knob to position

.
Lowerable exterior mirror* with the aid of the key for remote control – If all the windows are closed, press the unlock button on the radio
remote control
⇒
page 50, fig. 47
for approx. 2 seconds.
Tilting surface of front pa
ssenger exterior mirror*
When the rotary knob is in position
 ⇒fig. 72
and the reverse gear is engaged, the
s ur fa ce o f t h e m i rro r t i l ts d o w n s l i g h t l y. T h i s p ro v i d e s a n a i d i n s e e i n g th e ke r b o f t h e pavement when parking the car. The mirror returns into its initial position, after the rotary knob is moved out of the position
 and put into another position or if
the speed is more than 15 km/h.
Memory for exterior mirrors* On vehicles fitted with a memory for the driver seat, the relevant setting of the exte- rior mirror is also stored automatica
lly when the seat position is stored
⇒page 76.
WARNING
•
Convex (curved outward) or spherical (differently curved) exterior
mirrors increase the vision field. Th
ey do, however, make objects appear
smaller in the mirror. These mirrors are
only of limited use, therefore, for
estimating distances to the following vehicles.•
Use whenever possible the interior rear mirror, for estimating the
distances to the following vehicles.
Fig. 72 Inner part of door: Rotary knob
A3
se0.1.book Page 73 Friday, April 10, 2009 3:19 PM

Seats and Stowage
75
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Seats and StowageFront seatsBasic informationThe front seats have a wide range of differ
ent settings and can thus be matched to
the physical characteristics of the driver
and front passenger. Correct adjustment of
the seats is particularly important for:•
safely and quickly reaching the controls,
•
a relaxed, fatigue-free body position,
•
achieving the maximum protection offere
d by the seat belts and the airbag
system.
WARNING
•
Never transport more occupants than the maximum seating in the
vehicle.•
Each occupant must correctly fasten the seat belt belonging to the seat.
Children must be fastened
⇒page 184, “Transporting children safely” with
a suitable restraint system.•
The front seats and the head restraints must always be adjusted to match
the body size of the seat occupant as well as the seat belts must always be correctly fastened in order to provide an optimal protection for you and your occupants.•
Always keep your feet in the footwell
when the vehicle is being driven -
never place your feet on the instrument panel, out of the window or on the surfaces of the seats. This is particularly important for the front seat passenger. You will be exposed to increa
sed risk of injury if it becomes
necessary to apply the brake or in the ev
ent of an accident.
If an airbag is
deployed, you may suffer fatal injuries
when adopting an incorrect seated
position!•
It is important for the driver and front passenger to maintain a distance
of at least 25 cm from the steering wheel or dash panel. Not maintaining this
minimum distance will mean that the airb
ag system will not be able to prop-
erly protect you - hazard! The front seats and the head restraints must always also be correctly adjusted to match the body size of the occupant.•
Ensure that there are no objects in the footwell as any objects may get
behind the pedals during a driving or
braking manoeuvre. You would then
no longer be able to operate the clutch, to brake or accelerate.Adjusting the front seatsAdjusting a seat in a forward/back direction –Pull the lever
⇒
fig. 73
up and push the seat into the desired posi-
tion.
– Release the lever and push the seat further until the lock is heard
to engage.
Adjusting height of seat* – Lift the seat if required by pulling or pumping lever upwards.
WARNING (continued)
Fig. 73 Controls at seat
A1
A1
A2
se0.1.book Page 75 Friday, April 10, 2009 3:19 PM

Seats and Stowage
78
– Engage the reverse gear. – Move the right exterior mirror into the desired position
⇒
page 73.
– Take the vehicle out of gear. The set position of the exterior mirror is
stored.
Memory buttons Memory for the seat offers the possibility to store the individual driver seat and external mirror position. An individual posi
tion can be allocated to each of the three
memory buttons
⇒page 77, fig. 76
, that is three in total. After pressing the
corresponding memory button , the seat
and the exterior mirror are automati-
cally moved into the positions which
have been allocated to this button
⇒page 78.
Emergency Off You can interrupt the setting operation at an
y time, if you operate any button of the
driver seat.
Note
•
When storing settings with the memory buttons, we recommend that you begin
with the front button and assign a memory button to each additional driver.•
Each new setting stored with the same button erases the previous setting.
•
Each time you store the seat and exterior mirror settings for driving forward you
also have to re-store the individual settin
g of the exterior mirror on the passenger
side for reversing.Assigning remote control to the memory buttonsAfter storing the settings of the seat and exterior mirrors, you have 10 seconds in order to assign the radio remote control to the appropriate memory button. – Withdraw the ignition key. – Press the unlock button
⇒
page 50. The setting is stored with the
memory button which you have selected.
If you wish to be able to retrieve the settings which are stored in the memory by also using the radio remote control, you have
to assign the radio remote control to a
memory button in each case. If you wish, you can obtain an additional
remote control key from an authorised
Škoda Service partner and then assign the remote control key to another memory button.
Note
•
If the radio remote control had previous
ly been assigned to another memory
button, this setting is then erased by the new assignment.•
If you assign the radio remote contro
l to a memory button which has already
been assigned to a radio remote control,
the old assignment is also replaced by a
new assignment in this case.•
The assignment of the radio remote control to a memory button is retained,
however, after reassigning the seats and exterior mirrors.Retrieving settings of the seat and mirrors You can retrieve the stored settings
either with the memory buttons
or with the remote control*.Retrieving settings with memory buttons – In order to retrieve the stored
setting, you have two possibilities:
–
One-touch automatic memory:
Briefly press the desired memory
button
⇒
page 77, fig. 76
. The seat and exterior mirror are moved
automatically into the stored positions (this applies only if the ignition is switched on and the speed is less than 5 km/h).
–
Memory keying
: Press and hold the desired memory button
pressed long enough until the seat and the exterior mirror are moved into the stored positions.
AB
AB
AB
AB
se0.1.book Page 78 Friday, April 10, 2009 3:19 PM

Seats and Stowage
79
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Retrieving settings with remote control – If the driver door is closed and the ignition is switched off, briefly press
the unlock button of the radio remote control
⇒
page 50 and then
open the driver door.
– The seat and exterior mirrors now move automatically into the stored
positions.
Retrieving setting of exterior mirror for reversing* – Turn the rotary knob for the exterior mirror setting into the position

⇒
page 73 before engaging the reverse gear.
The mirror returns into its initial position,
after the rotary knob is moved out of the
position
 and put into another position or if the speed is more than 15 km/h.
Emergency Off You can interrupt the setting operation at any time, if you operate any button of the driver seat.
Note
If in the stored position the inclination an
gle of the seat backrest is more than 102°
in relation to the seat cushion, the seat backrest remains in this position, after reaching this angle, when
retrieving the setting by briefly pressing the memory
button. In order to achieve the stored setting, it is necessary to press the memory button again and hold it pressed until the seat is in the stored position.
Head restraintsBest protection is achieved if the top edge of the head restraint is at the same level as the uppe
r part of your head.
Adjusting the height of a head restraint – Grasp the side of the head restraint with both hands and push it in
upward direction as desired
⇒
fig. 77
.
– Move the head restraint downward
s if required by pressing and
holding the safety button with one hand
⇒
fig. 78
and by pressing
with the other hand the head restraint downwards.
Fig. 77 Adjusting head restraintFig. 78 Removing a head restraint
se0.1.book Page 79 Friday, April 10, 2009 3:19 PM

Seats and Stowage
80
Removing and installing a head restraint – Pull the head restraint up out of the seat backrest as far as the stop (on
the rear head restraints fold forward the seat backrest).
– Press the locking button in the direction of arrow
⇒
page 79, fig. 78

and pull the head restraint out.
– To re-insert the head restraint, push it down into the seat backrest far
enough until you hear the locking button engage.
The position of the front and rear outer head restraints is adjustable in height. The middle rear head restraint is adjustable in two positions. The head restraints must be adjusted to
match the size of the seat occupant.
Correctly adjusted head restraints togeth
er with the seat belts offer effective
protection for the occupants
⇒page 164, “Correct seated position”.
WARNING
•
The head restraints must be correctly adjusted in order to offer effective
protection for the occupants in the event of an accident.•
Do not drive under any circumstance with removed head restraints - risk
of injury!•
If the rear seats are occupied, the rear head restraint must not be in the
lower position.
Middle rear head restraintIIn certain countries national legal pr
ovisions also require the equipment
of the rear seat with fixing eyes for
child seat using the “Top Tether” system
⇒
page 191. For vehicles, which are eq
uipped with such fixing eyes, a
deviating sequence for removing th
e middle head restraint must be
observed. Removing and installing the rear middle head restraint – Pull the head restraint out of the
seat backrest as far as the stop.
– Press the locking button in the direction of arrow , press simultane-
ously the locking button into the opening using a flat screwdriver with a width of maximum 5 mm and pull out the head restraint.
– To re-insert the head restraint, push it down into the seat backrest far
enough until you hear the locking button engage.
WARNING
•
The head restraints must be correctly adjusted in order to offer effective
protection for the occupants in the event of an accident.•
Do not drive under any circumstance with removed head restraints - risk
of injury!
Fig. 79 Rear seats: middle head restraint
AA
AB
se0.1.book Page 80 Friday, April 10, 2009 3:19 PM