2009 Seat Leon 5D lights

If and when
256Turn signal lamps– Raise the bonnet.
– Rotate the lamp holder ⇒fig. 165 to the left and pull.
– Remove the bulb by pressing on the lamp holder and rotating at the same time to the left.
– Installation is done in the reverse order.
Dipped beam lights– Raise the bonnet
Fig. 165 Turn signal
lamps
AA
Fig. 166 Dipped head-
lightsFig. 167 Dipped head-
lights
Leon_EN.book Seite 256 Dienstag, 8. September 2009 5:25 17

If and when257
Safety First
Controls and equipment
Practical tips
Technical Data
– Remove the loops ⇒page 256, fig. 166 in the direction of
the arrow and remove the cover.
– Remove the connector ⇒page 256, fig. 167 from the bulb.
– Disengage the retainer spring ⇒ page 256, fig. 167 pressing
inwards to the right.
– Extract the bulb and fit the replacement so that the rim of the attachment plate is on the reflector cut-out.Main beam lights
– Raise the bonnet
– Remove the cover ⇒fig. 168 by pulling on this.
– Remove the connector ⇒fig. 169 from the bulb.
– Press the spring ⇒fig. 169 inwards and to the right.
– Extract the bulb and fit the replacement so that it sits correctly into the cut-out on the reflector.
– Installation is done in the reverse order.
A1
A2
A3
Fig. 168 Main beam
headlights
Fig. 169 Main beam
headlights
AC
A1
A2
Leon_EN.book Seite 257 Dienstag, 8. September 2009 5:25 17

If and when
258Side lights– Raise the bonnet.
– Remove the cover ⇒fig. 170 by pulling on this. – Extract the lamp holder
⇒fig. 171 outwards.
– Replace the bulb by pulling this out and inserting the replace- ment.
– Installation is done in the reverse order.
Rear lights•On the body
- Indicator, side and brake light•On the tailgate
- Left side: position and fog lights.
- Right side: reverse and position.
Fig. 170 Side lightsFig. 171 Side lights
AD
A1
Leon_EN.book Seite 258 Dienstag, 8. September 2009 5:25 17

If and when259
Safety First
Controls and equipment
Practical tips
Technical Data
Indicator, side and brake lights on the bodywork– Press on the side pin outwards and take out the lamp holder.
– Extract the failed bulb and change it for a new one.
– To refit follow the steps in reverse order, taking special care when
fitting the lamp holder.
Position light, fog light and reverse light on the tailgate–Open the tailgate.
– Use a screwdriver to remove the cover ⇒fig. 173 .
Fig. 172 Indicator, side
and brake lights on the
bodywork
Fig. 173 Lights on the
tailgateFig. 174 Removing the
lampholder
Leon_EN.book Seite 259 Dienstag, 8. September 2009 5:25 17

If and when261
Safety First
Controls and equipment
Practical tips
Technical Data
Luggage compartment lights– Remove the bulb by pressing on the inside edge of this -arrow-
using the flat side of a screwdriver ⇒fig. 176 . – Press the lamp sideways and remove from its housing
⇒fig. 177 .
– Installation is in the reverse order.
Fig. 176 Luggage
compartment lightFig. 177 Luggage
compartment light
Leon_EN.book Seite 261 Dienstag, 8. September 2009 5:25 17

If and when
264How to jump start: description⇒ fig. 182 shows the flat battery and the charged battery.
Jump lead terminal connections
– Switch off the ignition on both vehicles ⇒.
1. Connect one end of the red jump lead to the positive ⇒fig. 182
terminal of the vehicle with the flat battery ⇒.
2. Connect the other end of the red jump lead to the positive terminal in the vehicle providing assistance.
3. Connect one end of the black jump lead to the negative terminal on the battery of the vehicle providing assistance. 4. Connect the other end of the black jump lead to a solid metal
component which is bolted on to the engine block, or onto the
engine block itself of the vehicle with the flat battery. Do not
connect it to a point near the battery ⇒.
5. Position the leads in such a way that they cannot come into contact with any moving parts in the engine compartment.
Starting
6. Start the engine of the vehicle with the boosting battery and let it run at idling speed.
7. Start the engine of the car with the flat battery and wait one or two minutes until the engine is “running”.
Removing the jump leads
8. Before you remove the jump lead s, switch off the headlights (if
they are switched on).
9. Turn on the heater blower and rear window heater in the vehicle with the flat battery. This helps minimise voltage peaks which are
generated when the leads are disconnected.
10. When the engine is running, disconnect the leads in reverse order to the details given above.
Connect the battery clamps so they have good metal-to-metal contact with
the battery terminals.
If the engine fails to start, switch off the starter after about 10 seconds and
try again after about half a minute.
Fig. 182 How to connect
the jump leads
AA
AB
A+
A+
A-
AX
Leon_EN.book Seite 264 Dienstag, 8. September 2009 5:25 17

If and when267
Safety First
Controls and equipment
Practical tips
Technical Data
Do not pull too hard with the towing vehicle and take care to avoid jerking the
tow-rope. When towing on an unpaved road, there is always a risk of over-
loading and damaging the anchorage points.
The ignition of the vehicle being towed must be switched on to prevent the
steering wheel from locking and also to allow the use of the turn signals,
horn, windscreen wipers and washers.
As the brake servo does not work if the engine is not running, you must apply
considerably more pressure to the brake pedal than you normally would.
As the power assisted steering does not work if the engine is not running, you
will need more strength to steer than you normally would.
Towing vehicles with an automatic gearbox
•Put the selector lever into position “N”.•Do not drive faster than 50 km/h when towing a vehicle.•Do not tow further than 50 km.•If a breakdown vehicle is used, the vehicle must be towed with the front
wheels raised.Note
•Observe legal requirements when towing or tow-starting.•Switch on the hazard warning lights of both vehicles. However, observe
any regulations to the contrary.•For technical reasons, vehicles with an automatic gearbox must not be
tow-started.•If damage to your vehicle means that there is no lubricant in the gearbox,
you must raise the drive wheels while the vehicle is being towed.•If the vehicle has to be towed more than 50 km, the front wheels must be
raised during towing, and towing should be carried out by a qualified person.•The steering wheel is locked when the vehicle has no electrical power. The
vehicle must then be towed with the front wheels raised. Towing should be
carried out by a qualified person.
•The towing eye should always be kept in the vehicle. Please refer to the
notes on ⇒page 266.Trailer eyes
Fig. 183 The front right
section of the vehicle:
Fitting the front towing
eyeFig. 184 Fitting the
towing eye to the rear of
the vehicle
Leon_EN.book Seite 267 Dienstag, 8. September 2009 5:25 17

Index293
Index
AABS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Warning lamp . . . . . . . . . . . . . . . . . . . . . . . . . 79
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
Acoustic signal . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Acoustic warning . . . . . . . . . . . . . . . . . . . . . . . . 157
Adaptive headlights . . . . . . . . . . . . . . . . . . . . . 115
Adjusting the seat belt height . . . . . . . . . . . . . . 26
AFS (curve lights) . . . . . . . . . . . . . . . . . . . . . . . . 116
Air conditioner* 2C-Climatronic* . . . . . . . . . . . . . . . . . . . . . . 149
Air conditioning system General notes . . . . . . . . . . . . . . . . . . . . . . . . 153
Air conditioning* . . . . . . . . . . . . . . . . . . . . . . . . 145
Air recirculation mode 2C-Climatronic . . . . . . . . . . . . . . . . . . . . . . . 153
Manual air conditioning . . . . . . . . . . . . . . . 147
Airbag covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Airbag system . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Curtain airbags . . . . . . . . . . . . . . . . . . . . . . . 39
front airbags . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Side airbags . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Warning lamp . . . . . . . . . . . . . . . . . . . . . . . . . 30
Alarm system Switching off . . . . . . . . . . . . . . . . . . . . . . . . 102
Alternator Warning lamp . . . . . . . . . . . . . . . . . . . . . . . . . 80 Ambient temperature display . . . . . . . . . . . . 63, 71
Anti-freeze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
Anti-lock brake system . . . . . . . . . . . . . . . . . . . 182
Warning lamp . . . . . . . . . . . . . . . . . . . . . . . . . 79
Anti-puncture tyres . . . . . . . . . . . . . . . . . . . . . . 235
Anti-theft alarm system . . . . . . . . . . . . . . . . . . . 102 Switching off . . . . . . . . . . . . . . . . . . . . . . . . 102
Anti-theft wheel bolts . . . . . . . . . . . . . . . . . . . . 244
Aquaplaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
Ashtray* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Aspects to take into account before starting the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Automatic anti-dazzle interior mirror* Activating the anti-dazzle function . . . . . . 126
Deactivating anti-dazzle function . . . . . . . . 126
Automatic car wash tunnel . . . . . . . . . . . . . . . . 198
Automatic gearbox Kick-down feature . . . . . . . . . . . . . . . . . . . . 170
Automatic gearbox / DSG automatic gearbox . 166
Automatic lighting . . . . . . . . . . . . . . . . . . . . . . . 112
Automatic mode 2C-Climatronic . . . . . . . . . . . . . . . . . . . . . . . 151
Automatic wiper/wash function for the rear window 124
Auxiliary audio connection: AUX-IN . . . . . . . . . 138
BBall coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
BAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Battery Changing . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
Winter conditions . . . . . . . . . . . . . . . . . . . . 229
Before starting the vehicle . . . . . . . . . . . . . . . . . . 8
Belt tension device Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Warning lamp . . . . . . . . . . . . . . . . . . . . . . . . 30
Belt tension devices . . . . . . . . . . . . . . . . . . . . . . 27
Biodiesel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214
Biodiesel fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 214
Bonnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Brake assist system . . . . . . . . . . . . . . . . . . . . . 181
Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Changing . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
Brake pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
Brake servo . . . . . . . . . . . . . . . . . . . . . . . 181, 188
Brake system . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 Brake servo . . . . . . . . . . . . . . . . . . . . . . . . . 186
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
Warning lamp . . . . . . . . . . . . . . . . . . . . . . . . 81
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
Leon_EN.book Seite 293 Dienstag, 8. September 2009 5:25 17