2009 Seat Ibiza SC COMMUNICATION SYSTEM

Communication
16A running dialogue can be cancelled at any time by pressing button to
talk.
Note
•Say the command Repeat , if you would like to have the specified name
repeated by the system.•If you then say No, the system will answer with and the dialogue
will be ended.To erase the phone book
You can delete the entire phone book or single entries.– Press the talk button ⇒page 6, fig. 1 .
– After the tone, say the command DELETE PHONE BOOK.After giving this command you can delete the entire internal phone book or
single entries as desired. Example for deleting the entire internal telephone book:If no command is specified, the system responds after about 5
seconds with the next cue.
Dialogue
No command
are: yes, no, repeat,
back>
Dialogue
YES

DialogueEnd of
dialogueAF
AF
Speech command
Condition
Message
Action
DELETE PHONE
BOOK
The telephone
book contains
entries.
to delete the
whole phone
book?>
Dialogue
If no command is specified, the system responds after
about 5 seconds with the next cue.
Dialogue
No command
mands are: Yes,
no>
Dialogue
YES

Dialogue
If no command is specified, the system responds after
about 5 seconds with the next cue.
Dialogue
No command
mands are: Yes,
no>
Dialogue
YES
is deleted.>
All entries in the
phone book will
be deleted.End of dialogue
Sist Comunicacion_EN.book Seite 16 Mittwoch, 15. Juli 2009 6:45 18

Communication17
Controls and equipmentExample for deleting single names from the internal telephone book:
Notes on the phone book
Take note of these tips an
d suggestions when using the
phone book.•It is important that names stored in the phone book have a noticeable
acoustic difference between them so the system can recognise the entries.•In the event that an telephone book entry is not recognised (e.g. if
someone else tries to call-up a name), the phone book entries can be read out
by giving the command PLAY PHONE BOOK.•The numbers zero to nine are recognised by the system. Say the numbers
clearly so that the system can recognise them easily.
Should the system say , check the status of the
hands-free system as follows.•Is the phone switched on?•Has the PIN code been entered?
Speech command
Condition
Message
Action
DELETE PHONE
BOOK
The telephone
book contains
entries.
to delete the
whole phone
book?>
Dialogue
If no command is specified, the system responds after
about 5 seconds with the next cue.
Dialogue
No command
mands are: Yes,
no, repeat>
Dialogue
NO
The telephone
book will then be
read out.
No command
Talk button
pressed as the
entry to be
deleted is read
out.
delete the entry
(name)?>
Dialogue
If no command is specified, the system responds after
about 5 seconds with the next cue.
Dialogue

No command
mands are: Yes,
no>
Dialogue
YES
deleted.>
The entry will be
deleted and the
remaining
entries will be
read out.
All entries are
read out.
End of dialogue
Sist Comunicacion_EN.book Seite 17 Mittwoch, 15. Juli 2009 6:45 18

Communication
18
WARNING
The speech system must not be used in cases of emergency, since the voice
changes in stressful situations. This could result in a failed or delayed tele-
phone connection. For this reason, always enter emergency numbers
manually.International calls
Country and area codes can be entered as follows.Notes on entering telephone numbers for calls abroad:•When making a call abroad, you can say plus (+) before specifying the
digits.•After the plus (+) the country code must be specified. The country code
follows the conventional format (e.g. 49 for Germany or 44 for Great Britain.•After the country code, the zero (0) should be left out before the area
code.
Example for making a call to Great Britain:Speech command
Condition
Message
Action
DIAL NUMBER
Phone is
switched on.

Dialogue
PLUS, FOUR,
FOUR

Dialogue
SEVEN, THREE,
ONE

Dialogue
THREE, NINE,
TWO

Dialogue
DIAL
dialled.>
DialogueEnd of
dialogue
Sist Comunicacion_EN.book Seite 18 Mittwoch, 15. Juli 2009 6:45 18

Communication19
Controls and equipment
Voice command mobile telephone installation
- Models: Ibiza / Ibiza SCBasic functions
The voice command system can be activated with the “press
to talk” button, located on the multi-function control.See ⇒page 31, “Bluetooth®”
Talk button
The voice command system can be activated with the “press to talk”
button located on the multi-function control.
If one of these buttons is pressed while using the voice command system, the
function is cancelled.
After pressing the “press to talk” button ⇒fig. 9 , wait a few seconds for
the sound signal, after which the vocal commands may be used. These commands may be used to manage the functions of the hands-free telephone
system as well as the phone book.
Phone book
The speech control system offers the option of creating and using an phone
book belonging to the vehicle system and independent of the mobile tele-
phone. This phone book may contain 50 entries.
WARNING
•Please concentrate on driving. As the driver, you have the responsibility
for your safety and that of others. For this reason, you should only use the
functions in a manner that allows you to maintain control of the vehicle in
all situations - otherwise, you may create an accident risk!•The speech system must not be used in cases of emergency, since the
voice changes in stressful situations. This could result in a failed or delayed
telephone connection. Always dial emergency numbers manually!
Fig. 9 Talk button on the
multi-function control
AC
AC
Sist Comunicacion_EN.book Seite 19 Mittwoch, 15. Juli 2009 6:45 18

Communication
20Using the hands-free system from the multi-function control
The hands-free system can be activated using the multi-func-
tion control.As well as using the voice command system, it is possible to use the functions
of the hands-free system from the multi-function controls.
When connection is established between your mobile telephone and the
hands-free device, the phonebook in your telephone and/or your SIM card
(depending on the phone) is downloaded to the hands-free device.
Depending on the version, when the connection is established between your
mobile telephone and the hands-free device, the phonebook in the tele-
phone is downloaded to the hands-free device to recognise the contact of the
incoming call and the outgoing call. This phonebook cannot be managed
from the multi-function control. It cannot be viewed on the radio screen.
Fig. 10 Multi-function
control:
Sist Comunicacion_EN.book Seite 20 Mittwoch, 15. Juli 2009 6:45 18

Communication21
Controls and equipment
Example of incoming call An incoming call can be accepted by pressing the “answer call” button
⇒fig. 12 on the multi-function control and from the radio control
⇒ fig. 11 . If the number from which the incoming call is being made is associated with
a name in the existing phone book then the name will be displayed on the
radio display.
Fig. 11 Example of an incoming call from the radio
display
Fig. 12 Multi-function
control:
AE
AA
Sist Comunicacion_EN.book Seite 21 Mittwoch, 15. Juli 2009 6:45 18

Communication
22Information on radio displayAn incoming call is indicated on the display. To accept, press button on
the multifunction control or multi-function button on the radio ⇒
page 21, fig. 11 . To reject the call, press multi-function button on the
radio ⇒page 21, fig. 11 .
To cancel the outgoing call, press multi-function button on the radio
⇒ page 21, fig. 11 .
Information regarding the mobile phone coverage is displayed on the radio
display.
Dialogue
The voice command system can be activated with the “press
to talk” button, located on the multi-function control.In this manual, Dialogue is defined as the time in which the speech control
system may receive vocal commands and provide assistance for completion
of different functions in case the user is hesitant and unsure how to proceed.
The system also responds by vocal messages. The dialogue is started and
Fig. 13 Incoming callFig. 14 Outgoing phone
call
AE
AA
AB
ABFig. 15 Current phone
call
Sist Comunicacion_EN.book Seite 22 Mittwoch, 15. Juli 2009 6:45 18

Communication23
Controls and equipmentinterrupted by pressing the “press to talk” button
⇒page 21, fig. 12 or
by pressing on the radio screen.
If a call is received, then the dialogue is immediately interrupted. The call may
be accepted by pressing the key “answer” on the multi-function control.
Assistance from control commands when orders are not recognized.
If a command is not recognised by the system, it will answer with the cue
and the command can then be given once again clearly. After a
third failure the system will answer with and the dialogue will be
ended.
Note the following to ensure that you are properly understood:
•Speak in a normal tone and without pauses or exaggerated pronuncia-
tion.•Avoid poor articulation of words.•Keep the doors, windows and sun roof closed if possible to avoid back-
ground noises that might affect the system.•Keep the air vents directed away from the microphone (located on the
interior light).•At high speeds, you might need to speak louder to drown out background
noises.•Avoid other noises in the vehicle during a dialogue (e.g. other passengers
speaking in the vehicle).•Avoid speaking when the system is saying a cue.•The hands-free microphone is directed towards the driver, therefore, only
the driver should try to operate the system.•To make a call when there is heavy background noise we recommend
using the speech controlled telephone book instead of speaking individual
digits. This will help avoid mistakes when specifying telephone numbers.
Micro off
If, at any time, we do not wish to be heard by the person on the other end of
the line during a call, the vehicle microphone can be temporarily discon- nected. To do so, press the multi-function button on the radio
⇒page 21,
fig. 11 during the call.
To switch the microphone back on, press the multi-function button on the
radio again ⇒page 21, fig. 11 .
Controlling the hands-free unit by voice
The hands-free functions are also operated via voice
commands.Help commands
The system confirms acceptance of speech commands verbally and guides
you through the dialogue if necessary.
Commands for operating the hands-free system
AC
ok

Speech command
Action
HELP
Following this command the system announces
possible orders
Speech command
Action
DIAL NUMBER
After this command you can specify a telephone
number and establish a connection
REDIAL
After this command the last dialled telephone
number will be redialled
AA
AA
Sist Comunicacion_EN.book Seite 23 Mittwoch, 15. Juli 2009 6:45 18