2009 Seat Altea Owner's Manual

If and when
256Tu r n si g nal l a m ps– Raise the bonnet.
– Rotate the lamp holder ⇒fig. 178 to the left and pull.
– Remove the bulb by pressing on the lamp holder and rotating at the same time to the left.
– Installation is done in the reverse order.
Dipped beam lights–Raise the bonnet.
Fig. 178 Turn signal
lamps
AA
Fig. 179 Dipped head-
lightsFig. 180 Dipped head-
lights
Altea_EN.book Seite 256 Montag, 19. Januar 2009 1:31 13

If and when257
Safety First
Operating instructions
Practical tips
Te c h n i c a l D a t a
– Remove the loops ⇒page 256, fig. 179 in the direction of
the arrow and remove the cover.
– Remove the connector ⇒page 256, fig. 180 from the bulb.
– Disengage the retainer spring ⇒ page 256, fig. 180 pressing
inwards to the right.
– Extract the bulb and fit the replacement so that the rim of the attachment plate is on the reflector cut-out.Main beam lights
– Raise the bonnet.
– Remove the cover ⇒fig. 181 by pulling on this.
– Remove the connector ⇒fig. 182 from the bulb.
– Press the spring ⇒fig. 182 inwards and to the right.
– Extract the bulb and fit the replacement so that it sits correctly into the cut-out on the reflector.
– Installation is done in the reverse order.
A1
A2
A3
Fig. 181 Main beam
headlights
Fig. 182 Main beam
headlights
AC
A1
A2
Altea_EN.book Seite 257 Montag, 19. Januar 2009 1:31 13

If and when
258Side lights– Raise the bonnet.
– Remove the cover ⇒fig. 183 by pulling on this. – Extract the lamp holder
⇒fig. 184 outwards.
– Replace the bulb by pulling this out and inserting the replace- ment.
– Installation is done in the reverse order.
Rear lights•
Side lights
•
Brake lights
•
Turn signals
•
Reversing lights
•
Rear fog light
Fig. 183 Side lightsFig. 184 Side lights
AD
A1
Altea_EN.book Seite 258 Montag, 19. Januar 2009 1:31 13

If and when259
Safety First
Operating instructions
Practical tips
Te c h n i c a l D a t a
Side lights and brake lights– Open the tailgate.
– Remove the bolts ⇒fig. 185 . – Remove the cover of the luggage compartment lateral panel.
– Unscrew the plastic fitting
⇒fig. 186 securing the rear light.
Inserting a screwdriver under the plastic fitting may help to
loosen it.
– Partially remove the rear light from its casing taking care not to pull on the cable.
– Remove the lamp holder connector.
– Unscrew the bolts ⇒page 260, fig. 187 from the lamp holder
and pull on this.
– Press on the lamp and rotate to the left then fit the replacement.
– To refit follow the steps in reverse order, taking special care when fitting the lamp holder. The metal contacts of the lamp holder
ends should be correctly fitted with respect to the rear light
contacts.
Fig. 185 Side lights and
brake lightsFig. 186 Side lights and
brake lights
AA
ABAC
Altea_EN.book Seite 259 Montag, 19. Januar 2009 1:31 13

If and when
260Tu r n i n d i ca to rs– Remove the diode from its housing ⇒ page 259.– Unscrew the bolts ⇒
fig. 187 from the lamp holder and pull
on this.
– Pull out the indicator lamp holder using a screw driver in the direction of the arrow ⇒fig. 188.
– Fit the replacement lamp by pressing it down and rotating to the left.
– Installation is in the reverse order.
Reverse light / rear fog light– Rotate the lamp holder to the left, and remove it in the direction of the arrow ⇒fig. 189.
– Replace the bulb by pressing on it and rotating at the same time to the left.
Fig. 187 Indicator lightFig. 188 Indicator lights.
AC
Fig. 189 Lamp on interior
side of bumper
Altea_EN.book Seite 260 Montag, 19. Januar 2009 1:31 13

If and when261
Safety First
Operating instructions
Practical tips
Te c h n i c a l D a t a
Side indicators– Press the indicator to the left or to the right to remove the lamp.
– Remove the lamp holder from the indicator.
– Remove the failed glass bulb and replace with a new bulb.
– Insert the lamp holder in the indicator guide until it clicks into
place.
– First place the indicator in the opening in the bodywork, fixing the tabs ⇒fig. 190 , arrow .
– Insert the bulb as shown by the arrow ⇒fig. 190 .
Luggage compartment lights– Remove the bulb by pressing on the inside edge of this -arrow-
using the flat side of a screwdriver ⇒fig. 191.
Fig. 190 Side indicator
A1
A2
Fig. 191 Luggage
compartment lightFig. 192 Luggage
compartment light
Altea_EN.book Seite 261 Montag, 19. Januar 2009 1:31 13

If and when
262
– Press the lamp sideways and remove from its housing ⇒page 261, fig. 192 .Registration light
– Remove the bulb, carefully using the flat side of the screwdriver
as a lever inserted in the crack as shown by the arrow ⇒fig. 193.
– Remove the bulb, moving it in the direction of the arrow and outwards ⇒fig. 194 .
Fig. 193 Registration
light
Fig. 194 Registration
light
Altea_EN.book Seite 262 Montag, 19. Januar 2009 1:31 13

If and when263
Safety First
Operating instructions
Practical tips
Te c h n i c a l D a t a
Sunroof light– Carefully remove the lamp, using the flat side of the screwdriver,
as shown in the figure ⇒fig. 196. – Remove the bulb, moving it in
the direction of the arrow and
outwards ⇒fig. 196.
Jump-startingJump leads
The jump lead must have a sufficient wire cross section.If the engine fails to start because of a discharged battery, the battery can be
connected to the battery of another vehicle to start the engine.
Jump leads
Jump leads must comply with the standard DIN 72553 (see manufacturer's
documentation). The wire cross section must be at least 25 mm
2 for petrol
engines and at least 35 mm
2 for diesel engines.
Note
•
The vehicles must not touch each othe r, otherwise electricity could flow as
soon as the positive terminals are connected.
•
The discharged battery must be properly connected to the vehicle elec-
trical system.
Fig. 195 Removing
sunroof lightFig. 196 Removing
sunroof light
Altea_EN.book Seite 263 Montag, 19. Januar 2009 1:31 13