2009 SATURN VUE HYBRID fuel

Automatic Operation
This climate control system
automatically maintains the desired
temperature inside the vehicle.
Do not cover the sensor located on
the top of the instrument panel
near the windshield or the sensor
grille below the climate control
faceplate. These two sensors help
regulate the inside air temperature.
AUTO (Automatic Fan):Turn
the fan knob to AUTO for the system
to automatically adjust the fan
speed to reach the desired inside
temperature.
Temperature Control:Select the
desired air temperature between
60-90°F (16-32°C). Typically,
the best setting is near 75°F (23°C).
Choosing the coldest or warmest
temperature setting does not cause
the system to heat or cool any
faster.AUTO (Automatic Air Delivery
Mode):Turn the air delivery mode
knob to AUTO for the system to
automatically control the direction of
the airow to help reach the
desired inside temperature.
The system automatically controls
the air inlet to supply the outside air
or recirculated inside air needed
to cool the vehicle faster. The
indicator light on the recirculation
button will be lit whenever the
system changes to recirculation.
Press the recirculation button
to change to outside air. However,
the recirculation mode may turn
back on automatically.
In cold weather, if the fan and air
delivery modes are in automatic, the
system starts at lower fan speeds
to avoid directing cold air into
the vehicle until warmer air is
available. The climate control
system directs air to the oor, but
may automatically change modes as
the vehicle warms up to maintain
the chosen temperature setting.The length of time needed to warm
the interior depends on the
outside temperature and inside
temperature of the vehicle.
Manual Operation
It is best to use the automatic
settings to maximize fuel economy.
A(Fan Control):Turn clockwise
or counterclockwise to increase
or decrease the fan speed. To turn
the fan off, turn the left knob to
the
9position. In any setting other
than off, the fan runs continuously
with the ignition on. The fan must be
turned on to run the air conditioning
compressor. There will be some
airow noticeable from the various
outlets when driving, even with
the fan in the off position. This is to
ensure some fresh air is always
available in the vehicle. To turn off
the air completely, turn the fan
to
9and select the recirculation
button.
3-18 Instrument Panel
ProCarManuals.com

#(Normal Air Conditioning):
Press to turn the air conditioning
system on or off. An indicator
light comes on to show that the air
conditioning is on. Normal Air
Conditioning (A/C) can be selected
in any mode as long as the fan
is on and the outside air temperature
is above freezing. Normal A/C
cannot be selected at the same time
as Hybrid Air Conditioning (A/C).
A ashing indicator light indicates
that the air conditioning compressor
is currently not available.
When Normal A/C is selected, the
climate control system prevents
all automatic engine start/stop
operations. This will ensure the
cabin comfort is maintained.
See “Air Conditioning and Automatic
Engine Start/Stop” later in this
section.
N(Hybrid Air Conditioning):
Press to turn the Hybrid A/C system
on or off. An indicator light comes
on to show that Hybrid A/C is
on. Hybrid A/C can be selected inany mode, except defrost as long as
the fan is on and the outside air
temperature is above freezing.
Hybrid A/C cannot be selected at
the same time as the normal
air conditioning. A ashing indicator
light shows the air conditioning
compressor is not available.
The Hybrid A/C works to balance
fuel economy and air conditioning
comfort. When Hybrid A/C is used in
warm weather, the vehicle gets
better fuel economy by allowing
more frequent start/stops. For
additional cooling, select Normal
A/C. See “Air Conditioning and
Automatic Engine Start/Stop” later in
this section.
@(Recirculation):Press to
toggle between the recirculation and
outside air modes. The indicator
light turns on when the recirculation
mode is selected. This mode can
be used to prevent outside air
and odors from entering the vehicle
or to help cool the air inside the
vehicle more quickly. Avoid usingthe recirculation mode during high
periods of humidity and cool outside
temperatures since this may
result in increased window fogging.
If window fogging is experienced,
select the defrost mode.
Recirculation mode is not available
in oor, defog or defrost modes.
If the button is selected in
these modes, the indicator will ash.
This helps prevent window fogging
and moisture building up inside
the vehicle.
Rear Window Defogger
The rear window defogger uses a
warming grid to remove fog from the
rear window.
The rear window defogger will only
work when the ignition is in
ON/RUN.
<(Rear Window Defogger):
Press to turn the rear window
defogger on or off. An indicator light
on the button comes on to show
that it is activated.
3-20 Instrument Panel
ProCarManuals.com

Instrument Panel Cluster
The instrument panel cluster is designed to indicate how the vehicle is running. It shows how fast the vehicle is
going, about how much fuel the vehicle has left and many other things needed to drive safely and economically.United States cluster, Canada similar
Instrument Panel 3-23
ProCarManuals.com

Warnings and Messages on
page 3-42for more information.
Stop and check the tires as soon as
it is safe to do so. If underinated,
inate to the proper pressure.
SeeTires on page 5-38for more
information.
When the Light Flashes First and
Then is On Steady
This indicates that there could be a
problem with the Tire Pressure
Monitor System. The light ashes
for about a minute and stays
on steady for the remainder of the
ignition cycle. This sequence
repeats with every ignition cycle.
SeeTire Pressure Monitor System
on page 5-45for more information.Malfunction
Indicator Lamp
Check Engine Light
A computer system called OBD II
(On-Board Diagnostics-Second
Generation) monitors operation of
the fuel, ignition, and emission
control systems. It ensures
that emissions are at acceptable
levels for the life of the vehicle,
helping to produce a cleaner
environment.
This light comes on when the
ignition is on, but the engine is not
running, as a check to show it
is working. If it does not, have the
vehicle serviced by your
dealer/retailer.If the check engine light comes on
and stays on, while the engine
is running, this indicates that there
is an OBD II problem and service
is required.
Malfunctions often are indicated by
the system before any problem
is apparent. Being aware of the light
can prevent more serious damage
to the vehicle. This system
assists the service technician in
correctly diagnosing any
malfunction.
Notice:If the vehicle is
continually driven with this light
on, after a while, the emission
controls might not work as well,
the vehicle’s fuel economy
might not be as good, and the
engine might not run as
smoothly. This could lead to
costly repairs that might not be
covered by the vehicle warranty.
3-30 Instrument Panel
ProCarManuals.com

Notice:Modications made to
the engine, transmission, exhaust,
intake, or fuel system of the
vehicle or the replacement of the
original tires with other than those
of the same Tire Performance
Criteria (TPC) can affect the
vehicle’s emission controls and
can cause this light to come on.
Modications to these systems
could lead to costly repairs not
covered by the vehicle warranty.
This could also result in a failure
to pass a required Emission
Inspection/Maintenance test. See
Accessories and Modifications on
page 5-3.
This light comes on during a
malfunction in one of two ways:
Light Flashing:A misre condition
has been detected. A misre
increases vehicle emissions and
could damage the emission control
system on the vehicle. Diagnosis
and service might be required.The following can prevent more
serious damage to the vehicle:
Reduce vehicle speed.
Avoid hard accelerations.
Avoid steep uphill grades.
If towing a trailer, reduce the
amount of cargo being hauled
as soon as it is possible.
If the light continues to ash, when
it is safe to do so, stop the
vehicle. Find a safe place to park
the vehicle. Turn the key off, wait at
least 10 seconds, and restart the
engine. If the light is still ashing,
follow the previous steps and
see your dealer/retailer for service
as soon as possible.
Light On Steady:An emission
control system malfunction has been
detected on the vehicle. Diagnosis
and service might be required.An emission system malfunction
might be corrected by:
Make sure the fuel cap is fully
installed. SeeFilling the Tank
on page 5-7. The diagnostic
system can determine if the fuel
cap has been left off or
improperly installed. A loose or
missing fuel cap allows fuel
to evaporate into the atmosphere.
A few driving trips with the cap
properly installed should turn
the light off.
If the vehicle has been driven
through a deep puddle of
water, the vehicle’s electrical
system might be wet. The
condition is usually corrected
when the electrical system dries
out. A few driving trips should
turn the light off.
Instrument Panel 3-31
ProCarManuals.com

Make sure to fuel the vehicle
with quality fuel. Poor fuel
quality causes the engine not to
run as efficiently as designed
and may cause: stalling
after start-up, stalling when the
vehicle is changed into gear,
misring, hesitation on
acceleration, or stumbling on
acceleration. These conditions
might go away once the engine is
warmed up.
If one or more of these conditions
occurs, change the fuel brand
used. It will require at least
one full tank of the proper fuel to
turn the light off.
SeeGasoline Octane on
page 5-5.
If none of the above have made the
light turn off, your dealer/retailer can
check the vehicle. The dealer/retailer
has the proper test equipment and
diagnostic tools to x any mechanical
or electrical problems that might
have developed.Emissions Inspection and
Maintenance Programs
Some state/provincial and local
governments have or might begin
programs to inspect the emission
control equipment on the vehicle.
Failure to pass this inspection could
prevent getting a vehicle
registration.
Here are some things to know to
help the vehicle pass an inspection:
The vehicle will not pass this
inspection if the check engine
light is on with the engine
running, or if the key is in
ON/RUN and the light is not on.
The vehicle will not pass this
inspection if the OBD II
(on-board diagnostic) system
determines that critical emission
control systems have not
been completely diagnosed by
the system. The vehicle would be
considered not ready for
inspection. This can happen if
the battery has recently been
replaced or if the battery has run
down. The diagnostic system
is designed to evaluate critical
emission control systems
during normal driving. This can
take several days of routine
driving. If this has been done and
the vehicle still does not pass
the inspection for lack of OBD II
system readiness, your
dealer/retailer can prepare the
vehicle for inspection.
3-32 Instrument Panel
ProCarManuals.com

Highbeam On Light
The highbeam on light comes on
when the high-beam headlamps are
in use.
SeeHeadlamp High/Low-Beam
Changer on page 3-7for more
information.
Low Washer Fluid
Warning Light
The low washer uid warning light
comes on when the windshield
washer uid is low. SeeWindshield
Washer Fluid on page 5-24for
more information.
Fuel Gage
When the ignition is on, the fuel
gage shows about how much fuel is
in the fuel tank.
An arrow on the fuel gage indicates
the side of the vehicle the fuel
door is on.
When the indicator nears empty, the
low fuel light comes on. There still
is a little fuel left, but the fuel
tank should be refueled soon. See
Low Fuel Warning Light on
page 3-34for more information.
Four things that can happen but do
not mean the fuel gage is not
functioning properly are:
At the service station, the fuel
pump shuts off before the
gage reads full.
It takes a little more or less fuel
to ll up than the fuel gage
indicates.
The gage moves a little while
turning a corner or accelerating.
The gage takes a few seconds to
stabilize after the ignition is
turned on, and goes back
to empty after the ignition is
turned off.
For the fuel tank capacity, see
Capacities and Specifications on
page 5-81.
Low Fuel Warning Light
The low fuel warning light, below
the fuel gage, comes on briey when
the engine is started.
United StatesCanada
3-34 Instrument Panel
ProCarManuals.com

This light also comes on when the
fuel tank is low on fuel. When fuel is
added, the light should go off. If it
does not, have the vehicle serviced.
Auto Stop Mode
This mark on the tachometer
signies that the engine is in Auto
Stop mode which is a fuel saving
operation.
When the vehicle is off, the
tachometer needle moves to OFF. If
the driver’s door is opened while
in Auto Stop, a chime sounds.
Charge/Assist Gage
The CHARGE/ASSIST gage
displays the charge into and out of
the hybrid battery.
When the gage indicates ASSIST,
the electric motor is performing
an automatic restart of the engine,
or the electric motor is assisting
for maximum acceleration.
When the gage indicates CHARGE,
the electric motor operates as a
generator to perform regenerative
braking, while decelerating. See
Regenerative Braking on page 2-23
for more information.
The gage also indicates CHARGE
when the system is recharging
the hybrid battery.If the hybrid battery or other hybrid
components are very hot or cold, the
CHARGE and ASSIST functions can
be suspended until the component
temperatures are normal.
Fuel Economy Light
The ECO light comes on when the
vehicle is achieving fuel economy
close to its rated performance.
Driving habits that improve
fuel economy increases the time
that the fuel economy light is on.
To enable or disable the fuel
economy light, while in park, press
the Vehicle Info button on the
DIC until PRESS
VTO SET ECO is
displayed. Then press the set/reset
button to select off or on. For
more information seeTrip Odometer
on page 3-24andDIC Operation
and Displays on page 3-36. United States
Canada
Instrument Panel 3-35
ProCarManuals.com