2009 SATURN ASTRA stop start
[x] Cancel search: stop startPage 82 of 314
Turn and Lane-Change
Signals
To signal a turn, move the lever all
the way up or down, past the
detent. The lever returns to its
starting position when released.
An arrow on the instrument panel
cluster ashes in the direction of the
turn or lane change.
To signal a lane change, raise or
lower the lever until the arrow starts
to ash, and then release the
lever. Do not move the lever past
the detent. The turn signal will
automatically ash three times and
turn off.
To cancel it before turning, move
the lever slightly in either direction.
Do not past the detent.
If the turn signal is moved up or down
and left engaged, the headlamps and
taillamps will remain on and the
battery could be drained.
Headlamp High/
Low-Beam Changer
23
(Headlamp High/Low
Beam Changer):To change the
headlamps from low to high
beam, push the multifunction lever
towards the instrument panel.
To return to low-beam headlamps,
push the lever towards the
instrument panel again or pull the
lever toward you. Then release it.
This indicator light on the instrument
panel cluster is on while the high
beam headlamps are on.
Flash-to-Pass
Pull the turn signal/multifunction
lever towards you to ash the high
beams from low beam.
Windshield Wipers
Clear ice and snow from the wiper
blades before using them. If the
wiper blades are frozen to the
windshield, gently loosen or thaw
them. If the blades do become
damaged, install new blades or blade
inserts. SeeWindshield Wiper Blade
Replacement on page 9-21.
Heavy snow or ice can overload the
wiper motor. A circuit breaker will
stop the motor until it cools down.
Clear away snow or ice to prevent
an overload.
4-8 Instruments and Controls
ProCarManuals.com
Page 90 of 314
Charging System Light
The charging system light comes on
brie y when the ignition is turned
on, but the engine is not running,
as a check to show the light is
working. It should go out when the
engine is started.
If the light stays on, or comes on
while driving, there could be a
problem with the electrical charging
system. Have it checked by your
dealer/retailer. Driving while this light
is on could drain the battery.
If a short distance must be driven
with the light on, be sure to turn off
all accessories, such as the radio
and air conditioner.
Brake System Warning
Light
The brake indicator light should
come on brie y as the engine
is started. If it does not come on
have the vehicle serviced by
your dealer/retailer.
When the ignition is on, the brake
system warning light comes on
when the parking brake is set.
The light stays on if the parking
brake does not fully release.
If it stays on after the parking brake
is fully released, there is a brake
problem. Have the brake system
inspected immediately.
{CAUTION
The brake system might not be
working properly if the brake
system warning light is on.
Driving with the brake system
warning light on can lead to a
crash. If the light is still on after
the vehicle has been pulled off
the road and carefully stopped,
have the vehicle towed for
service.
If the light comes on while driving, a
chime sounds. Pull off the road
and stop. The pedal might be harder
to push or go closer to the oor.
It might also take longer to stop.
If the light is still on, have the vehicle
towed for service. SeeTowing
Your Vehicle on page 9-73.
United StatesCanada
4-16 Instruments and Controls
ProCarManuals.com
Page 91 of 314
Antilock Brake System
(ABS) Warning Light
The Antilock Brake System (ABS)
light will come on brie y, as a check,
when you start your vehicle.
If it does not, have your vehicle
serviced so that the light works
properly when it needs to.
If the light stays on longer than a
few seconds after you start your
engine, or comes on and stays on
while you are driving, try resetting
the system. To reset the system:
1. If you are driving, pull over when
it is safe to do so. It may take
longer to stop the vehicle.
2. Place the vehicle in P (Park).
3. Turn off the ignition.
4. Then restart the engine.If the light remains on after resetting
the system or comes on again
while driving, your vehicle needs
service. The antilock brakes are not
working properly and there might
be a problem stopping the vehicle.
Pull off the road and stop. It may
take longer to stop the vehicle. If the
light is still on, have the vehicle
towed for service. SeeTowing Your
Vehicle on page 9-73for more
information.
{CAUTION
Your brake system may not be
working properly if the Antilock
Brake System (ABS) light is on.
Driving with the ABS light on can
lead to an accident. If the light is
still on after you have pulled off
the road and stopped carefully,
have the vehicle towed for
service.
StabiliTrak®Indicator
Light
For vehicles with this light, it should
come on brie y when the ignition is
turned on.
If the light does not come on, have it
xed so it will be ready to warn if
there is a problem.
If the light stays on, or comes on
while driving there may be a
problem with the StabiliTrak
system and your vehicle may
need service. When this light is on,
the StabiliTrak system does not
assist in controlling the vehicle.
Adjust your driving accordingly.
SeeStabiliTrak
®System on
page 8-19for more information.
When the system is active, the light
will ash while the system helps
control the vehicle. You may also
feel or hear the system working.
This is normal.
Instruments and Controls 4-17
ProCarManuals.com
Page 92 of 314
Engine Coolant
Temperature Warning
Light
The engine coolant temperature
light should come on brie y as the
engine is started. If it does not
come on have the vehicle serviced
by your dealer/retailer.
Notice:Driving with the engine
coolant temperature warning light
on could cause the vehicle to
overheat. SeeEngine Overheating
on page 9-18. The vehicle’s engine
could be damaged, and it might
not be covered by the vehicle
warranty. Never drive with the
engine coolant temperature
warning light on.
If this light comes on and stays on,
the engine has overheated. Pull
over and seeEngine Overheating on
page 9-18for more information.
Tire Pressure Light
For vehicles with this light, it comes
on brie y as a check when the
ignition is turned on.
This light comes on and stays on
when one or more of the vehicle’s
tires are signi cantly underin ated.
Stop and check the tires as
soon as it is safe to do so.
If underin ated, in ate to the proper
pressure. SeeTires on page 9-40
for more information.
This light ashes for approximately
one minute and then stays on
when the system detects a
malfunction. SeeTire Pressure
Monitor System on page 9-49for
more information.
Malfunction
Indicator Lamp
Check Engine Light
A computer system called OBD II
(On-Board Diagnostics-Second
Generation) monitors operation of
the fuel, ignition, and emission
control systems. It makes sure
that emissions are at acceptable
levels for the life of the vehicle,
helping to produce a cleaner
environment.
This light should come on when
the ignition is on, but the engine
is not running, as check to show
it is working. If it does not, have
the vehicle serviced by your
dealer/retailer.
4-18 Instruments and Controls
ProCarManuals.com
Page 93 of 314
If the check engine light comes on
and stays on, while the engine
is running, this indicates that there
is an OBD II problem and service
is required.
Malfunctions often are indicated by
the system before any problem
is apparent. Heeding the light can
prevent more serious damage to the
vehicle. This system is also
designed to assist the service
technician in correctly diagnosing
any malfunction.
Notice:If the vehicle is
continually driven with this light
on, after a while, the emission
controls might not work as well,
the vehicle’s fuel economy
might not be as good, and the
engine might not run as
smoothly. This could lead to
costly repairs that might not be
covered by the vehicle warranty.Notice:Modi cations made
to the engine, transmission,
exhaust, intake, or fuel system of
the vehicle or the replacement
of the original tires with other
than those of the same Tire
Performance Criteria (TPC) can
affect the vehicle’s emission
controls and can cause this light
to come on. Modi cations to
these systems could lead to
costly repairs not covered by
the vehicle warranty. This could
also result in a failure to
pass a required Emission
Inspection/Maintenance test.
SeeAccessories and
Modifications on page 9-3.This light comes on during a
malfunction in one of two ways:
Light Flashing:A mis re condition
has been detected. A mis re
increases vehicle emissions and
could damage the emission control
system on the vehicle. Diagnosis
and service might be required.
The following can prevent more
serious damage to the vehicle:
Reduce vehicle speed.
Avoid hard accelerations.
Avoid steep uphill grades.
If the light continues to ash, when
it is safe to do so, stop the
vehicle. Find a safe place to park
the vehicle. Turn the key off, wait at
least 10 seconds, and restart the
engine. If the light is still ashing,
follow the previous steps and
see your dealer/retailer for service
as soon as possible.
Instruments and Controls 4-19
ProCarManuals.com
Page 104 of 314
Distance Travelled
This display shows the current
distance traveled in either
miles (mi) or kilometers (km)
since the last reset.
The measurement can be reset to
zero at any time and restarted.
See “Reset” later in this section.
Average Speed
This display shows the average
speed of the vehicle in miles
per hour (mph) or kilometers per
hour (km/h). This average is
calculated based on the various
vehicle speeds recorded since the
last reset of this value.
The measurement can be reset to
zero at any time and restarted.
See “Reset” later in this section.Trip Consumption
This display shows the number of
gallons (gal) or liters (l) of fuel
used since the last reset.
The measurement can be reset to
zero at any time and restarted.
See “Reset” later in this section.
Average Consumption
This display shows the approximate
average miles per gallon (mpg) or
liters per 100 kilometers (l/100 km).
This number is calculated based on
the number of mpg (l/100 km)
recorded since the last time this
menu item was reset.
The measurement can be reset to
zero at any time and restarted.
See “Reset” later in this section.Timer
This display can be used as a timer.
Select Timer from the menu.
The Timer menu will display.
To start the timer, select Start.
To reset the timer, select Reset.
The desired stop watch displays can
be selected from the Options menu,
if your vehicle has this feature:
Driving Time excl. Stops:The time
the vehicle is in motion is recorded.
Stationary time is not included.
Driving Time incl. Stops:The time
the vehicle is in motion is recorded
along with the time the vehicle
is stationary with the key in the
ignition.
Travel Time:Measurement of
the time from manual activation,
by selecting Start, to manual
deactivation, by selecting Reset.
4-30 Instruments and Controls
ProCarManuals.com
Page 109 of 314
Distance Travelled
This display shows the current
distance traveled in either
miles (mi) or kilometers (km) since
the last reset.
The measurement can be reset to
zero at any time and restarted.
See “Reset” later in this section.
Range
This display shows the approximate
number of remaining miles (mi)
or kilometers (km) the vehicle can
be driven without refueling.
The message “Range” displays if
less than 31 mi (50 km) can be
driven with the fuel remaining in
the tank. The message “Refuel!”
displays when approximately
19 mi (30 km) can be driven with
the fuel remaining in the tank.With less than 19 mi (30 km)
worth of fuel remaining the range
display will show “- -” once the
“Refuel!” message has been
acknowledged.
SeeDIC Warnings and Messages
(Base and Uplevel Systems) on
page 4-36for information on
acknowledging the message.
The fuel range estimate is based on
an average of the vehicle’s fuel
economy over recent driving history
and the amount of fuel remaining
in the fuel tank. This estimate
will change if driving conditions
change. For example, if driving
in traffic and making frequent stops,
this display may read one number,
but if the vehicle is driven on a
freeway, the number may change
even though the same amount
of fuel is in the fuel tank.This is because different driving
conditions produce different fuel
economies. Generally, freeway
driving produces better fuel
economy than city driving.
Fuel range cannot be reset.
Stop Watch
This display can be used as a timer.
To start or stop the timer, press
the right arrow on the audio system.
To reset the timer, press the left
arrow until the value returns to zero.
If your vehicle has the left
thumbwheel on the steering wheel,
you can start or stop the timer
by pressing the thumbwheel.
Instruments and Controls 4-35
ProCarManuals.com
Page 124 of 314
On Volume
The On Volume is used to set the
maximum initial volume level for the
audio system when it is turned on.
The maximum initial volume level is
used only if the volume level
before turning the audio system off
was higher than the maximum
initial volume level set. This will work
when the audio system has been
off for at least ve minutes and the
ignition is OFF.
To set the On Volume level:
1. Press SETTINGS until Audio
appears.
2. Press OK until On Volume
appears.
3. Press
\or]to adjust the level
from -12 through 12. The setting
is saved automatically.
Press SETTINGS again to go
back one level in the menu.
Press FM/AM, CD/MP3, or BC to
display that function.
Using the Radio
FM/AM:Press to select between
FM, FM-AS, AM, and AM-AS,
or to listen to the radio while a CD
is playing.
RDS (Radio Data System):Press
to identify stations by name
instead of the radio frequency.
LOC (LOCAL/DX Function):Press
to change between LOC ON or LOC
OFF. When the LOC function is on, it
searches for the strongest radio
frequency. If none is found, it
automatically search for a weaker
radio frequency. If no frequency is
found after the second search, the
radio returns to the last active
frequency. If a new station search is
not started within one minute, the low
sensitivity (LOCAL) is set when the
next search is started. When LOC
OFF is set, a search is carried out
using the high sensitivity (DX).Finding an FM/AM Station
1 - 9 (Station Preset Buttons):
Press to play stations that are
programmed to the radio preset
pushbuttons.
SCN (Station Preset Scan):Press
to start station preset scan. The
radio goes to the rst preset station,
plays for a few seconds, then
goes to the next preset station.
Press SCN again to stop scanning
preset stations.
\or]:Press to nd radio stations
using the automatic station search
or the manual station search.
Automatic Station Search:Use
automatic station search when
the radio frequency is unknown.
Press
\or]for more then
one second to have the radio search
for the next station. Seek is shown
on the display and the radio is
muted until a station is found.
6-6 Infotainment
ProCarManuals.com