2009 RENAULT TWINGO RS lock

77A-3
FRONT SEAT TRIM
Front seat base trim: Removal - Refitting
77A
aRemove the « cover - foam » assembly.
aCut the clips (6) using a cutting tool.
aCut the clips (7) using a cutting tool.
aDetach the cover from the foam.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the cover on the foam.
aFit the clips (7) and (6) (available from the Spare
Parts Department) using the (Car. 1521).
aRefit the « cover - foam » assembly onto the seat
base frame.
aAttach the clips (5) .aLock the seat base cover tensioner.
aRefit:
-the seat base cover elastic strap (3) ,
-the elastic straps (2) securing the seatback cover.
aClip on the seatback adjustment control.
aRefit the cover (1) .
II - FINAL OPERATION.
aRefit the complete front seat (see 75A, Front seat
frames and mechanisms, Complete front seat:
Removal - Refitting, page 75A-8) .
aConnect the battery ( (see Battery: Removal - Re-
fitting) ).
aUnlock the airbag computer using the Diagnostic
tool (see MR 413 Fault finding, 88C, Airbags and
seat belt pretensioners, Fault finding - Replace-
ment of components).
120832
120833

77A-4
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting
77A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see MR 413 Fault finding, 88C, Airbags and seat
belt pretensioners, Fault finding - Replacement
of components).
aDisconnect the battery ( (see Battery: Removal -
Refitting) ).
aRemove the complete front seat (see 75A, Front
seat frames and mechanisms, Complete front
seat: Removal - Refitting, page 75A-8) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
1 - 1st type
aUnlock the headrest at (1) .
aRemove the headrest.
aRemove the cover (2) . Special tooling required
Car. 1521Clip cr imping pliers.
Equipment required
Diagnostic tool
IMPORTANT
To prevent any accidental triggering whilst w orking
on or near a pyrotechnic component (airbags or
pretensioners), lock the airbag computer using the
Diagnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
120834
120835

77A-6
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting
77A
aUnclip the headrest guides (6) .
aRemove:
-the seatback cover,
-the seatback foam.
2 - 2nd type
aUnlock the headrest at (7) .
aRemove the headrest.aRemove:
-the bolt (8) ,
-the lever from the control accessing the rear seats.
aRemove:
-the bolts (9) ,
-the plate from the control accessing the rear seats.
120838
120834112944
112945

77A-8
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting
77A
aRemove:
-the clips (14) ,
-the retaining strip (15) .
aUnclip the headrest guides (16) .
aRemove:
-the seatback cover,
-the seatback foam.3 - 3rd type
aUnlock the headrest at (17) .
aRemove the headrest.
aFold the seat away.
aUnclip:
-the seatback plate (18) ,
-the casings (19) .
121032
120838
120834
121458

77A-12
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting
77A
-the bolt (20) ,
-the headrest.
II - FINAL OPERATION.
aRefit the complete front seat (see 75A, Front seat
frames and mechanisms, Complete front seat:
Removal - Refitting, page 75A-8) .
aConnect the battery ( (see Battery: Removal - Re-
fitting) ).
aUnlock the airbag computer using the Diagnostic
tool (see MR 413 Fault finding, 88C, Airbags and
seat belt pretensioners, Fault finding - Replace-
ment of components).

79A-1
SEAT ACCESSORIES
Heated seat pad: Removal - Refitting
FRONT SEAT WITH HEATING
79A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(88C, Airbags and pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove:
-the compete front seat (see 75A, Front seat fra-
mes and mechanisms, Complete front seat: Re-
moval - Refitting, page 75A-8) ,
-the front seat base trim (see 77A, Front seat trim,
Front seat base trim: Removal - Refitting, page
77A-1) ,
-the front seatback trim (see 77A, Front seat trim,
Front seatback trim: Removal - Refitting, page
77A-4) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
Front seatback
Front seat base
aDetach the heated pad. Equipment required
Diagnostic tool
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
131163
131164
WARNING
To avoid any damage to the foam, detach the
heated pad carefully.

79A-2
SEAT ACCESSORIES
Heated seat pad: Removal - Refitting
FRONT SEAT WITH HEATING
79A
REFITTING
I - REFITTING PREPARATION OPERATION
a
II - REFITTING OPERATION FOR PART
CONCERNED
aRemove the protective backing from the adhesive of
the heated pad.
aBond the heated pad.
aRefit:
-the front seat frame,
-the « foam - heated pad » assembly of the seat
base and seatback.
aConnect the connectors:
-of the heated pad,
-of the heated seat switch.
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
aCarry out a function test.
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aDisconnect the following connectors :
-of the heated seat switch,
-of the heated pad.
aRemove:
-the « foam - heated pad » assembly of the seat
base and seatback,
-the front seat frame.III - FINAL OPERATION.
aRefit:
-the front seatback trim (see 77A, Front seat trim,
Front seatback trim: Removal - Refitting, page
77A-4) ,
-the front seat base trim (see 77A, Front seat trim,
Front seat base trim: Removal - Refitting, page
77A-1) ,
-the entire front seat (see 75A, Front seat frames
and mechanisms, Complete front seat: Remo-
val - Refitting, page 75A-8) .
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (88C, Airbags and pretensioners). Note:
Check the condition of the seat base and seat-
back foam pads and replace them if necessary.