2009 RENAULT TWINGO RS lock

75A-6
FRONT SEAT FRAMES AND MECHANISMS
Front seat runner: Removal - Refitting
75A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(88C, Airbags and pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove:
-the compete front seat (see 75A, Front seat fra-
mes and mechanisms, Complete front seat: Re-
moval - Refitting, page 75A-8) ,
-the front buckle pretensioner (see Front buckle
pretensioner: Removal - Refitting) (88C, Airbags
and pretensioners).aRemove the unlocking cable from the front seat run-
ners.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the nuts (1) from the front seat runner,
-the front seat runners.
REFITTING
I - REFITTING PREPARATION OPERATION
aAlways replace the front seat runner nuts. Equipment required
Diagnostic tool
Tightening torquesm
front seat runner nuts25 Nm
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
120852
120850

75A-7
FRONT SEAT FRAMES AND MECHANISMS
Front seat runner: Removal - Refitting
75A
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the front seat runners without tightening them,
-the front seat runner control (2) .
aObserve the tightening order:
-the runner on the vehicle interior side (3) ,
-the runner on the vehicle exterior side (4) .
aTighten:
-the runners, holding them towards the interior of
the seat at (5) and (6) ,
-to torque the front seat runner nuts (25 Nm) (1) .
III - FINAL OPERATION.
aRefit:
-the unlocking cable of the front seat runners,
-the front buckle pretensioner (see Front buckle
pretensioner: Removal - Refitting) (88C, Airbags
and pretensioners),
-the entire front seat (see 75A, Front seat frames
and mechanisms, Complete front seat: Remo-
val - Refitting, page 75A-8) .
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents)(88C, Airbags and pretensioners).
127773

75A-8
FRONT SEAT FRAMES AND MECHANISMS
Complete front seat: Removal - Refitting
75A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and seat belt pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).aUnclip the cover (1) located under the front seat.
aDisconnect the connector (2) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the blanking covers (3) ,
-the front seat nuts (3) . Equipment required
Diagnostic tool
Tightening torquesm
front seat nuts35 Nm
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
120814
121326

75A-9
FRONT SEAT FRAMES AND MECHANISMS
Complete front seat: Removal - Refitting
75A
REFITTING
I - REFITTING PREPARATIONS OPERATION
aAlways replace the front seat nuts.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the front seat nuts (3) .
aTorque tighten the front seat nuts (35 Nm).
aRefit the blanking covers (3) .
III - FINAL OPERATION.
aConnect the connector (2) .
aClip on the cover (1) located under the front seat.
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (MR 413, 88C, Airbags and seat belt preten-
sioners).

76A-1
REAR SEAT FRAMES AND MECHANISMS
Complete rear seat: Removal - Refitting
76A
REMOVAL
OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the bolts (1) from the rear seat.
aTilt the rear seatback.aTilt the rear seat assembly by pulling on the handles
(2) .
aUnlock the seat belt (3) . Tightening torquesm
rear seat bolts21 Nm
120795
120941
120942
120797

76A-5
REAR SEAT FRAMES AND MECHANISMS
Rear bench seatback: Removal - Refitting
76A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the rear parcel shelf (depending on the
equipment level).
aPull down the rear bench seat base.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnlock the rear bench seatback using the straps (1)
.
aPull down the rear bench seatback.aUnlock the rear bench seatback catches.
aRemove the rear bench seat seatback.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the rear bench seatback.
aLock the rear bench seatback catches.
aPull down the rear bench seatback.
II - FINAL OPERATION.
aPull down the rear bench seat base.
aRefit the rear parcel shelf (depending on the equip-
ment level).
121303
121302

77A-1
FRONT SEAT TRIM
Front seat base trim: Removal - Refitting
77A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see MR 413 Fault finding, 88C, Airbags and seat
belt pretensioners, Fault finding - Replacement
of components).
aDisconnect the battery ( (see Battery: Removal -
Refitting) ).
aRemove the complete front seat (see 75A, Front
seat frames and mechanisms, Complete front
seat: Removal - Refitting, page 75A-8) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the cover (1) .
aUnclip the seatback adjustment control. Special tooling required
Car. 1521Clip cr imping pliers.
Equipment required
Diagnostic tool
IMPORTANT
To prevent any accidental triggering whilst w orking
on or near a pyrotechnic component (airbags or
pretensioners), lock the airbag computer using the
Diagnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
120809
120810

77A-2
FRONT SEAT TRIM
Front seat base trim: Removal - Refitting
77A
aRemove the elastic securing straps (2) from the
seatback trim.
aRemove the elastic securing straps (3) from the seat
base trim.aUnlock the seat base cover tensioner at (4) using a
flat-blade screwdriver.
aUnclip the clips (5) using unclipping pliers.
120811
120812120813
120831