2009 RENAULT TWINGO RS window

54A-4
WINDOWS
Rear quarter panel window: Removal - Refitting
54A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:
-the rear panel trim (see Rear panel lining: Remo-
val - Refitting) (71A, Body internal trim),
-the rear quarter panel trim (see Quarter panel
trim: Removal - Refitting) (71A, Body internal
trim).
-the B-pillar upper trim (see B-pillar upper trim:
Removal - Refitting) (71A, Body internal trim).
aProtect the edges of the quarter panel window using
masking tape.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aBegin cutting the cement bead.
REFITTING
I - REFITTING PREPARATION OPERATION
aAlways replace the stops and shims.
aFor preparation and bonding (see Technical Note
560A).II - REFITTING OPERATION FOR PART
CONCERNED
aBond the rear quarter panel window.
aEqual out the clearances and shut lines.
aRemove the tabs from the stops when the adhesive
has dried.
III - FINAL OPERATION.
aRefit:
-the B-pillar upper trim (see B-pillar upper trim:
Removal - Refitting) (71A, Body internal trim),
-the rear quarter panel trim (see Quarter panel
trim: Removal - Refitting) (71A, Body internal
trim).
-the rear panel trim (see Rear panel lining: Remo-
val - Refitting) (71A, Body internal trim).
119267
Note:
Leave a minimum clearance of 3.5 mm between
the rear quar ter panel window and the upper
section of the panelwork. This clearance is
necessary for fitting the transverse bars.

54A-5
WINDOWS
Rear screen: Removal - Refitting
54A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the rear screen wiper arm (see Rear
screen wiper arm: Removal - Refitting) (MR 411,
85A, Wiping - Washing).
aUnclip the exterior trim (1) from the rear screen.
aRemove the tailgate trim (see Tailgate trim: Remo-
val - Refitting) (MR 412, 73A, Non-side opening
element trim).
aDisconnect the rear screen de-icer connectors.II - OPERATION FOR REMOVAL OF PART
CONCERNED
aProtect the edges of the rear screen using masking
tape.
aBegin cutting the cement bead.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aAlways replace the stops and shims.
aFor preparation and bonding of the rear screen win-
dow, see Technical Note 560A, General window
and sunroof bonding procedure.
II - REFITTING OPERATION FOR PART
CONCERNED
aBond the rear screen (two people are required for
this operation).
aEqual out the clearances and shut lines.
aRemove the tabs from the stops when the adhesive
has dried.
III - FINAL OPERATION.
aConnect the rear screen de-icer connectors.
aRefit the tailgate trim (see Tailgate trim: Removal -
Refitting) (MR 412, 73A, Non-side opening element
trim).
aClip on the rear screen exterior trim (1) .
119525
119290

54A-6
WINDOWS
Rear screen: Removal - Refitting
54A
aRefit the rear screen wiper arm (see Rear screen
wiper arm: Removal - Refitting) (MR 411, Mecha-
nical 85A, Wiping - Washing).

54A-7
WINDOWS
Sunroof fixed window: Removal - Refitting
54A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and seat belt pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aRemove:
-the headlining (see Headlining: Removal - Refit-
ting) (MR 412, 71A, Body internal trim),
-the roof protection strips (see 55A, Exterior pro-
tection, Roof protection strip: Removal - Refit-
ting, page 55A-17) .
aProtect:
-the sunroof's fixed window surround and the rear
section of the roof using masking tape,
-the inside of the vehicle.II - REMOVAL OPERATION FOR PART
CONCERNED
aCut the cement bead; this operation requires two
people.
aRemove the fixed window from the sunroof.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aPosition the new shims on the sunroof operating me-
chanism.
aFor preparation and bonding (see Technical Note
560A).
II - REFITTING OPERATION FOR PART
CONCERNED
aBond the sunroof fixed window using the specific
support (this operation requires two people):
-Support: PARV 202,
-set of arch supports: APARV 200 ESP. Equipment required
Diagnostic tool
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
121153

54A-8
WINDOWS
Sunroof fixed window: Removal - Refitting
54A
Respect the clearances and shut lines
aObserve the 6 mm clearance between the sunroof
fixed window (1) and the sunroof mobile panel (2) .
aThe sunroof's fixed window (1) should be slightly
lower than its mobile panel (2) .
aArrange the lateral clearances so that they are
equal.
III - FINAL OPERATION.
aRefit:
-the headlining (see Headlining: Removal - Refit-
ting) (MR 412, 71A, Body internal trim),
-the roof protection strips (see 55A, Exterior pro-
tection, Roof protection strip: Removal - Refit-
ting, page 55A-17) .
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aUnlock the airbag computer using Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners).
113525

56A-11
EXTERIOR EQUIPMENT
Side decorative strips: Removal - Refitting
56A
a
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:
-the front door exterior weatherstrip (see Front side
door exterior weatherstrip: Removal - Refitting)
,
-the front door glass run channel (see Front side
door window run channel: Removal - Refitting) .
II - REMOVAL OPERATION FOR PART
CONCERNED
aStrip off the side decorative strip using a hot air gun.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aClean the adhesive surface of the film with heptane
and wipe with a lint-free cloth.II - REFITTING OPERATION FOR PART
CONCERNED
aPosition the decorative strip to be bonded to the
door pillar and visually centre it with the rear quarter
panel window end piece (1) .
aHold the lower section of the decorative strip in place
with masking tape.
aTurn back the top of the decorative strip and pull
away the protective paper to mark.
aStick the side decorative strip down taking care to
keep it properly aligned.
aPull away the protective paper from the upper sec-
tion of the decorative strip.
aPull away the protective paper from the upper sec-
tion of the decorative strip.
aStick down the upper section smoothing it with a
plastic spatula from bottom to top in a continuous
movement.
aPull away the masking tape from the lower section of
the side decorative strip.
aSmooth from top to bottom with the plastic spatula in
a continuous movement, gradually pulling away the
protective paper following the progression of the
bonding taking care to ensure that it stays aligned. Note:
Once removed, the side decorative strips cannot
be refitted and must be replaced each time.
120790
120790
WARNING
Do not press too heavily on the plastic spatula
otherwise you may stretch and deform the side
decorative strip.