2009 RENAULT TWINGO RS fuel

17A-4
IGNITION
Coils: Removal - Refitting
D4F, and 772
17A
aWhen refitting the spark plug wiring, always apply a
bead of FLUOSTAR 2L (2 mm in diameter) to the in-
ner edge of the high-tension caps on the side of the
spark plugs and coil.
aConnect:
-the ignition coil connector,
-the ignition coil high voltage wiring harness.
II - FINAL OPERATION
aRefit the air filter unit (see 12A, Fuel mixture, Air fil-
ter unit: Removal - Refitting, page 12A-13) .
aConnect the battery (see Battery: Removal - Refit-
ting) .
106640

17A-15
IGNITION
Plugs: Removal - Refitting
D4F, and 780 – D4F, and 782
17A
aIt is essential to apply a bead of FLUOSTAR 2L
(see Vehicle: Parts and consumables for the re-
pair) (04B, Consumables - Products) with a diame-
ter of 2 mm to the inner edge of the high tension
caps on the spark plug and ignition coil side.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the spark plugs.
aTorque tighten the spark plugs (23 N.m) using the
(Ele. 1933) fitted with the (Ele. 1382-01).
III - FINAL OPERATION
aConnect the ignition wiring harnesses to the spark
plugs.
aRefit the air filter unit (see 12A, Fuel mixture, Air fil-
ter unit: Removal - Refitting, page 12A-13) .
106640

17A-17
IGNITION
Plugs: Removal - Refitting
D4F, and 772
17A
Spark plug electrode gap
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the air filter unit (see 12A, Fuel mixture,
Air filter unit: Removal - Refitting, page 12A-13) .a
Disconnect the spark plug wiring.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the spark plugs using the (Ele. 1933) (1)
equipped with the (Ele. 1382-01) (2) . Special tooling required
Ele. 193323 N.m tightening wrench for
spar k plugs
Ele. 1382-0114 mm Plug spanner.
Equipment required
set of feeler gauges
Tightening torquesm
spar k plugs23 N.m
Type of spark plug Gap (mm)
CHAMPION 0.90 ± 0.05
NGK 0.85 ± 0.05
132677
WARNING
To disconnect the spark plug leads, pull on the
extensions and not on the leads.
132700

17A-19
IGNITION
Plugs: Removal - Refitting
D4F, and 772
17A
III - FINAL OPERATION
aApply a bead of FLUORSTAR 2L grease (see Vehi-
cle: Parts and consumables for the repair) (04B,
Consumables - Products) 2 mm in diameter on the
internal perimeter of the high-tension caps at the
spark plug end.
aConnect the spark plug wiring.
aRefit the air filter unit (see 12A, Fuel mixture, Air fil-
ter unit: Removal - Refitting, page 12A-13) .
106640

17B-5
PETROL INJECTION
Petrol injection: List and location of components
D4F, and 780 or 782
17B
122387
(1) Fuel vapour recirculation sole-
noid valve
(2) Upstream oxygen sensor
(3) Petrol injection computer
(4) Motorised throttle valve
(5) Ignition coil
(6) Engine compar tment connec-
tion unit
(7) Intake distributor pressure sen-
sor
(8) Turbocharger
108254
(9) Fuel injection computer

17B-6
PETROL INJECTION
Petrol injection: List and location of components
D4F, and 780 or 782
17B
121764
(10) Throttle valve
108802
(11) Fuel vapour recirculation sole-
noid valve
120958
(12) Ignition coil
120957
(13) Upstream oxygen sensor

17B-9
PETROL INJECTION
Petrol injection: List and location of components
K4M
17B
131776
(1) Fuel vapour absorber bleed
solenoid valve
(2) Camshaft dephaser solenoid
valve
(3) Air inlet pressure sensor
(4) Coil
(5) Throttle valve
(6) Petrol injection computer
(7) Switching protection unit
(8) Coolant temper ature sensor
(9) Camshaft position sensor
(10) Pinking sensor
(11) Oil pressure sensor
(12) Air temperature sensor
(13) Injector rail
131766
(1) Fuel vapour absorber bleed
solenoid valve

17B-15
PETROL INJECTION
Oxygen sensors: Removal - Refitting
D4F, and 780 or 782
17B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
1 - Removing the upstream oxygen sensor
aRemove the air filter unit (see 12A, Fuel mixture,
Air filter unit: Removal - Refitting, page 12A-13) .aDisconnect the upstream oxygen sensor connector
(1) .
aUnclip the upstream oxygen sensor connector from
the rocker cover.
aUnclip the upstream oxygen sensor wiring (2) .
aRemove:
-the bolts (3) from the exhaust manifold heat shield,
-the turbocharger heat shield,
-the upstream oxygen sensor (4) from the catalytic
converter using the tool (Mot. 1495-01). Special tooling required
Mot. 1495-0122 mm socket for removal -
refitting of oxygen sensors.
Tightening torquesm
upstream oxygen sen-
sor45 N.m
turbocharger heat shield
bolts8 N.m
downstream oxygen
sensor45 N.m
WARNING
Do not use any product designed to improve the
electr ical contact in the injection computer and oxy-
gen sensor connectors or on the bodies of the oxy-
gen sensors.
Failure to respect this advice causes the oxygen
sensor to malfunction and results in failure to com-
ply with the emission control standard.
WARNING
If the connections are corroded, repair the wiring
(see Wiring: Precautions for repair) (Technical
Note 6015A, 88A, Wiring).
120957
120957