2009 RENAULT TWINGO RS fuel

19C-13
TANK
Fuel level sensor module: Removal - Refitting
D4F or D7F or K4M or K9K
19C
REMOVAL
I - REMOVAL PREPARATION OPERATION
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aDrain the tank (see 19C, Tank, Fuel tank: Draining,
page 19C-1) .
aLift up:
-the rear bench seat base (see Rear bench seat
base: Removal - Refitting) (76A, Rear seat
frames and runners),
-the carpet under the rear bench seat base.aRemove the inspection flap blanking cover (1) . Special tooling required
Mot. 1397Universal spanner for remov-
ing fuel gauge nuts .
IMPORTANT
During this oper ation, be sure to:
-refrain from smoking or bringing red hot objects
close to the working area,
-be careful of fuel splashes when disconnecting the
union.
IMPORTANT
Wear goggles with side protectors for this opera-
tion.
IMPORTANT
Wear leaktight gloves (Nitrile type) for this opera-
tion.
WARNING
To prevent impurities from entering the circuit, place
protective plugs on all fuel circuit components
exposed to the open air.
WARNING
To avoid any corrosion or damage, protect the
areas on which fuel is likely to run.
104545

19C-14
TANK
Fuel level sensor module: Removal - Refitting
D4F or D7F or K4M or K9K
19C
aDisconnect:
-the fuel level sensor module connector (2) ,
-the fuel pipes (3) .aDisconnect:
-the fuel level sensor module connector (4) ,
-the fuel pipe (5) . D4F or D7F or K9K
18577
WARNING
Prepare for the flow of fluid, and protect the sur-
rounding components.
K4M
131774
WARNING
Prepare for the flow of fluid, and protect the sur-
rounding components.

19C-15
TANK
Fuel level sensor module: Removal - Refitting
D4F or D7F or K4M or K9K
19C
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the nut from the fuel level sensor module using the
tool (Mot. 1397) (6) ,
-the fuel level sensor module.
REFITTING
I - REFITTING PREPARATION OPERATION
aAlways replace:
-the nut of the fuel level sensor module,
-the fuel level sensor module seal.II - REFITTING OPERATION FOR PART
CONCERNED
aPosition:
-the new seal (8) in the neck correctly,
-the fuel level sensor module (7) on the fuel tank
(10) .
aUse a hand to press the fuel level sensor module to
grip the seal.
aManually pretighten the new nut (9) on the fuel tank.
104547
WARNING
To prevent the tank from deforming, refit the fuel
sender unit nut to the tank well immediately.
118996
Note:
A lug on the fuel level sensor module and a
recess in the fuel tank ensure correct positioning
in the fuel tank.

19C-16
TANK
Fuel level sensor module: Removal - Refitting
D4F or D7F or K4M or K9K
19C
aTighten the fuel level sensor module nut using the
tool (Mot. 1397) until the nut mark (11) corresponds
with the fuel tank mark (12) .
III - FINAL OPERATION
aConnect:
-the fuel pipe,
-the fuel level sensor module connector.
aConnect:
-the fuel pipes,
-the fuel level sensor module connector.
aRefit the inspection flap cover.
aFit:
-the carpet under the rear bench seat base.
-the rear bench seat base (see Rear bench seat
base: Removal - Refitting) (76A, Rear seat
frames and runners).
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
102470
K4M
D4F or D7F or K9K

19D-10
ENGINE MOUNTING
Left-hand suspended engine mounting: Removal - Refitting
K4M
19D
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the battery (see Battery: Removal - Refitting)
(80A, Battery),
-the petrol injection computer (see 17B, Petrol in-
jection, Petrol injection computer: Removal -
Refitting, page 17B-20) ,
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the battery tray (see Battery tray: Removal - Re-
fitting) (80A, Battery),
-the front left-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the front left-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection).
aMark the position of the left-hand suspended engine
mounting.aPut a 20 mm shim between the gearbox and the
sub-frame. Tightening torquesm
bolts of the suspended
engine mounting sup-
por t on the gearbox62 N.m
gearbox suspended
engine mounting rubber
pad shaft105 N.m
bolts of the suspended
engine mounting sup-
por t on the body21 N.m
bolts of the suspended
mounting r ubber pad62 N.m
suspended engine
mounting shaft nut62 N.m
120778

19D-12
ENGINE MOUNTING
Left-hand suspended engine mounting: Removal - Refitting
K4M
19D
aTorque tighten:
-the gearbox suspended engine mounting rub-
ber pad shaft (105 N.m) (8) ,
-the bolts of the suspended engine mounting
support on the body (21 N.m).
aFit the wiring of the suspended engine mounting
support on the body.
aRefit the suspended engine mounting rubber pad.
aTorque tighten:
-the bolts of the suspended mounting rubber
pad (62 N.m),
-the suspended engine mounting shaft nut (62
N.m).
II - FINAL OPERATION
aRemove the shim between the gearbox and the sub-
frame.
aRefit:
-the front left-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection),
-the front left-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the battery tray (see Battery tray: Removal - Re-
fitting) (80A, Battery),
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,-the petrol injection computer (see 17B, Petrol in-
jection, Petrol injection computer: Removal -
Refitting, page 17B-20) ,
-the battery (see Battery: Removal - Refitting)
(80A, Battery).
130485

19D-13
ENGINE MOUNTING
Right-hand suspended engine mounting: Removal - Refitting
C44, and K9K
19D
PARTS AND CONSUMABLES FOR THE
REPAIR WORK
aParts always to be replaced:
-axle sub-frame bolt.
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift ( (see Vehicle:
Towing and lifting) ).
aFit the (1) (Mot. 1672) to the vehicle after removing
the front right-hand bolt on the axle sub-frame and
the rear left-hand bolt on the axle sub-frame.
aSupport the lower engine cover on the (Mot. 1672)
by pressing on the tool support.II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the fuel supply pipes (2) from the right-hand
suspended engine mounting.
aUndo the clip on the right-hand suspended engine
mounting.
aRemove the fuel filler cap from the expansion bottle.
aUndo the nut on the fuel filter cage.
aRemove the fuel filter.
aRemove the fuel filter cage bolts.
aRemove the fuel filter cage. Special tooling required
Mot. 1672Low er engine support.
Tightening torquesm
right-hand suspended
engine mounting bolts
on the engine62 Nm
right-hand suspended
engine mounting bolts
on the body62 Nm
axle sub-frame front
bolts62 Nm
axle sub-frame rear
bolts105 Nm
120040
120045

19D-14
ENGINE MOUNTING
Right-hand suspended engine mounting: Removal - Refitting
C44, and K9K
19D
aRemove:
-the right-hand suspended engine mounting bolts
(3) on the engine,
-the right-hand suspended engine mounting bolts
(4) on the body,
-the right-hand suspended engine mounting.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the right-hand suspended engine mounting,
-the right-hand suspended engine mounting bolts
on the body,
-the right-hand suspended engine mounting bolts
on the engine.
aTighten all bolts on the suspended engine mounting
until they make contact.
aTorque tighten:
-the right-hand suspended engine mounting
bolts on the engine (62 Nm),
-the right-hand suspended engine mounting
bolts on the body ( 62 Nm).
aFit the clip to the right-hand suspended engine
mounting.
aPosition the fuel filter cage.aRefit the fuel filter cage bolts.
aPosition the fuel filter.
aTighten the fuel filter cage nut.
aClip on the fuel pipes.
II - FINAL OPERATION.
aRefit the expansion bottle bolt.
aRemove the (Mot. 1672).
aTighten the new bolts on the axle sub-frame until
they make contact.
aTorque tighten:
-the axle sub-frame front bolts (62 Nm),
-the axle sub-frame rear bolts (105 Nm).
120047
Note:
Make sure that the clip on the high pressure
pump side is proper ly clipped onto the right-hand
suspended engine mounting.