2009 RENAULT TWINGO RS battery

19B-14
EXHAUST
Catalytic converter: Removal - Refitting
K9K
19B
aIf they are replaced, torque tighten the catalytic
converter studs on the turbocharger (9 Nm ).
II - REFITTING OPERATION FOR PART
CONCERNED
aFrom underneath the vehicle, fit:
-the catalytic converter on the turbocharger fitted
with a new seal between the catalytic converter
and the turbocharger,
-one of the catalytic converter nuts on the turbo-
charger.
aIn order, fit (without tightening):
-the catalytic converter upstream strut bolts on the
engine,
-the catalytic converter downstream strut bolt and
nut on the gearbox,
-the catalytic converter upstream strut bolts on the
catalytic converter,
-the catalytic converter downstream strut bolt on the
catalytic converter,
-the catalytic converter nuts on the turbocharger,
aTorque tighten and in order:
-the catalytic converter nuts on the turbocharger
(26 Nm),
-the catalytic converter upstream strut bolts on
the engine (44 Nm),
-the catalytic converter downstream strut bolts
on the gearbox (21 Nm),
-the catalytic converter downstream strut nut on
the gearbox (21 Nm),
-the catalytic converter upstream strut bolts on
the catalytic converter (26 Nm),
-the catalytic converter downstream strut bolt
on the catalytic converter (21 Nm).
aFit in order:
-a new exhaust system sealing ring on the catalytic
converter,
-the exhaust pipe on the catalytic converter,
-the exhaust pipe springs and bolts on the catalytic
converter.aTorque tighten the exhaust pipe bolts on the cata-
lytic converter (21 Nm).
aCheck the following and deal with if necessary:
-that there is no contact with the underbody,
-the presence and correct positioning of all the ex-
haust pipe heat shields.
III - FINAL OPERATION.
aRefit:
-the engine tie-bar (see 19D, Engine mounting,
Lower engine tie-bar: Removal - Refitting, page
19D-18) ,
-the air filter box (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the scoop under the scuttle panel grille ( (see
Scoop under the scuttle panel grille: Removal -
Refitting) ),
-the scuttle panel grille ( (see Scuttle panel grille:
Removal - Refitting) ),
-the windscreen wiper arms ( (see Windscreen
wiper arm: Removal - Refitting) ).
aConnect the battery ( (see Battery: Removal - Re-
fitting) ).
aStart the engine.
aCheck that there are no leaks and deal with them if
necessary. Note:
Check that there is no contact between the cata-
lytic conver ter and the turbocharger oil return
pipe during the entire catalytic converter tighten-
ing operation.

19B-16
EXHAUST
Catalytic converter: Removal - Refitting
D4F, and 780 or 782
19B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aRemove:
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the air filter box strut bolt,-the air filter box strut,
-the upstream oxygen sensor (see 17B, Petrol in-
jection, Oxygen sensors: Removal - Refitting,
page 17B-13) . Tightening torquesm
catalytic converter lower
bracket bolt on the gear-
box44 N.m
bolts of the catalytic
converter lower bracket
on the engine25 N.m
side bracket bolts on the
catalytic converter21 N.m
side bracket bolts on the
engine21 N.m
catalytic converter nuts
on the turbocharger (ini-
tial torque)20 N.m
catalytic converter nuts
on the turbocharger30 N.m
bolts of the catalytic
converter lower bracket
on the catalytic con-
verter (initial torque)20 N.m
bolts of the catalytic
converter lower bracket
on the catalytic con-
verter30 N.m
exhaust downpipe bolts21 N.m
catalytic converter strut
nut21 N.m
catalytic converter strut
bolt on the rocker cover21 N.m

19B-21
EXHAUST
Catalytic converter: Removal - Refitting
D4F, and 780 or 782
19B
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).

19C-1
TANK
Fuel tank: Draining
K9K
19C
I - DRAINING PREPARATION OPERATION
aDisconnect the battery (see ) (MR 441, 80A, Bat-
tery).
aRemove the front engine cover.aDisconnect the engine fuel supply quick-release
union (1) from the fuel filter outlet.
II - DRAINING THE FUEL TANK
aConnect a pneumatic transfer pump for fuels to
the fuel filter outlet.
aDrain the fuel tank.
III - FINAL OPERATION.
aDisconnect the pneumatic transfer pump for fuels
from the fuel filter.
aConnect the engine fuel filter outlet engine supply
quick-release union to the fuel filter.
aRefit the engine cover.
aConnect the battery (see ) (MR 441, 80A, Battery). Equipment required
pneumatic transfer pump for fuels
IMPORTANT
During this oper ation, be sure to:
-refrain from smoking or bringing red hot objects
close to the working area,
-be careful of fuel splashes when disconnecting the
union.
IMPORTANT
Wear goggles with side protectors for this opera-
tion.
IMPORTANT
Wear latex gloves during the operation.
WARNING
To prevent impurities from entering the circuit, plugs
must be fitted to the openings of all the fuel circuit
components exposed to the open air.
WARNING
To avoid any corrosion or damage, protect the
areas on which fuel is likely to run.
121441

19C-2
TANK
Fuel tank: Draining
D4F or D7F or K4M
19C
I - DRAINING PREPARATION OPERATION
aDisconnect the battery (see ) (80A, Battery).
aRemove the engine oil filler neck.aDisconnect the fuel supply union (1) from the injector
rail.
aFit a T (Mot. 1311-08) union. Special tooling required
Mot. 1311-08Union for taking fuel pres-
sure measurements .
Equipment required
pneumatic transfer pump for fuels
IMPORTANT
During this oper ation, be sure to:
-refrain from smoking or bringing red hot objects
close to the working area,
-be careful of fuel splashes when disconnecting the
union.
IMPORTANT
Wear goggles with side protectors for this opera-
tion.
IMPORTANT
Wear leaktight gloves (Nitrile type) for this opera-
tion.
WARNING
To prevent impurities from entering the circuit, place
protective plugs on all fuel circuit components
exposed to the open air.
WARNING
To avoid any corrosion or damage, protect the
areas on which fuel is likely to run.
D4F
D4F
121778

19C-3
TANK
Fuel tank: Draining
D4F or D7F or K4M
19C
aDisconnect the fuel supply union (2) from the injector
rail.
aFit a T (Mot. 1311-08) union.aDisconnect the fuel supply union (3) from the injector
rail.
aFit a T (Mot. 1311-08) union.
II - TANK DRAINING PROCEDURE
aConnect a pneumatic transfer pump for fuels on
the outlet of the "T" union.
aDrain the fuel tank.
III - FINAL OPERATION.
aDisconnect the pneumatic transfer pump for fu-
els. .
aRemove the “T” union (Mot. 1311-08).
aConnect the fuel supply union.
aRefit the engine oil filler neck.
aConnect the battery (see ) (80A, Battery). D7F
121779
K4M
132334
D4F

19C-4
TANK
Fuel tank: Removal - Refitting
D4F or D7F or K4M or K9K
19C
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aDrain the fuel tank (see 19C, Tank, Fuel tank:
Draining, page 19C-1) .
aLift up:
-the rear bench seat,
-the carpet.
aRemove the access flap (1) to the fuel level sensor
module. Equipment requiredcomponent support
Tightening torquesm
tank bolts21 N.m
exhaust pipe rubber
mounting bush bolt21 N.m
clip between the cata-
lytic converter and the
rear silencer21 N.m
IMPORTANT
During this oper ation, be sure to:
-refrain from smoking or bringing red hot objects
close to the working area,
-be careful of fuel splashes when disconnecting the
union.
IMPORTANT
Wear leaktight gloves (Nitrile type) for this opera-
tion.
IMPORTANT
Wear goggles with side protectors for this opera-
tion.
WARNING
To prevent impurities from entering the circuit, plugs
must be fitted to the openings of all the fuel circuit
components exposed to the open air.
WARNING
To avoid any corrosion or damage, protect the
areas on which fuel is likely to run.
119692

19C-10
TANK
Fuel tank: Removal - Refitting
D4F or D7F or K4M or K9K
19C
aRefit:
-the heat shield under the tank,
-the heat shield clips under the tank
aTighten to torque:
-the exhaust pipe rubber mounting bush bolt (21
N.m),
-the clip between the catalytic converter and the
rear silencer (21 N.m).
aClip:
-the handbrake cable onto the flange,
-the handbrake cable onto the secondary brake
shoe.
aRefit the rear brake drums (see Rear brake drum:
Removal - Refitting) (33A,Rear axle components).
aRefit the rear wheels (see Wheel: Removal - Refit-
ting) (35A, Wheels and tyres).
aConnect:
-the fuel level sensor module pipe union,
-the fuel level sensor module connector.
aRefit the access flap for the fuel level sensor mod-
ule.
aRefit the rear bench seat.
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery). D4F or D7F or K9K