2009 RENAULT TWINGO RS battery

19A-17
COOLING
Cooling radiator: Removal - Refitting
K9K
19A
-the top hose on the radiator,
-the bottom hose on the radiator.
a
aLubricate the seals with the recommended air condi-
tioning oil to facilitate fitting.
aFit the condenser connecting pipes.
aFit the connecting pipe unions to the condenser.
aRefit the plastic cover on the condenser.
aConnect the pressostat connector.
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
aConnect the battery (see ) (80A, Battery).
aFill and bleed the cooling system (see 19A, Cool-
ing, Cooling system: Draining - Refilling, page
19A-9) .aCheck that the system is operating correctly (see Air
conditioning: Check) (62A, Air conditioning).
aFill the refrigerant circuit using a refrigerant charg-
ing station (see Refrigerant circuit: Draining -
Filling) (62A, Air conditioning).
aCheck the refrigerant circuit (see Refrigerant cir-
cuit: Check) (62A, Air conditioning). AIR CONDITIONING
WARNING
Do not remove the blanking plugs from each
component until the last moment.
Also, do not remove the components from their
packaging until they are to be fitted to the vehi-
cle.
WARNING
To avoid any leaks, check that the seal and the
pipe surface are in good condition. The seal and
the surface must be clean and scratch free.
AIR CONDITIONING

19A-18
COOLING
Cooling radiator: Removal - Refitting
D4F or D7F, and STANDARD HEATING
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aDisconnect the battery (see ) (MR 411, 80A, Bat-
tery).
aRemove:
-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection).
aDisconnect the air filter unit air inlet pipe (1) from the
air filter unit cover.
aRemove:
-the air filter unit air inlet pipe bolt from the cross
member (2) ,-the air filter unit air inlet pipe.
aDrain the cooling system (see 19A, Cooling, Cool-
ing system: Draining - Refilling, page 19A-9) .
aRemove using the (Mot. 1448) :
-the radiator top hose clip,
-the radiator degassing hose clip.
aDisconnect:
-the radiator top hose,
-the radiator degassing hose.
aUnclip:
-the lower hose from the engine cooling fan assem-
bly,
-the wiring harness from the engine cooling fan as-
sembly.
aDisconnect the engine cooling fan assembly con-
nectors.
II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove:
-the radiator mounting cross member (see Radiator
mounting cross member: Removal - Refitting)
(MR 412, 41A, Front lower structure),
-the « radiator / engine cooling fan assembly » unit.
Stripping the cooling radiator
aRemove the radiator plastic deflectors.
aUnclip the engine cooling fan assembly.
REFITTING
I - REFITTING PREPARATIONS OPERATION
Rebuilding the cooling radiator
aClip the engine cooling fan assembly in place.
aRefit the radiator plastic deflectors.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the « radiator / engine cooling fan assembly » unit, Special tooling required
Mot. 1448Remote operation pliers for
hose clips .
D4F, and 780
122833

19A-19
COOLING
Cooling radiator: Removal - Refitting
D4F or D7F, and STANDARD HEATING
19A
-the radiator mounting cross member (see Radiator
mounting cross member: Removal - Refitting)
(MR 412, 41A, Front lower structure).
III - FINAL OPERATION
aConnect the engine cooling fan assembly connec-
tors.
aClip:
-the wiring harness to the engine cooling fan as-
sembly,
-the bottom hose to the engine cooling fan assem-
bly.
aConnect:
-the radiator degassing hose,
-the radiator top hose.
aUsing the (Mot. 1448), fit:
-the radiator degassing hose clip,
-the radiator top hose clip.
aRefit:
-the air filter box air inlet pipe,
-the air filter unit air inlet pipe bolt on the cross
member.
aConnect the air filter unit air inlet pipe to the air filter
unit cover.
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres).
aConnect the battery (see ) (MR 411, 80A, Battery).
aFill and bleed the cooling system (see 19A, Cool-
ing, Cooling system: Draining - Refilling, page
19A-9) . D4F, and 780

19A-20
COOLING
Cooling radiator: Removal - Refitting
K4M
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aDrain the air conditioning circuit using a refrigerant
charging station (see Refrigerant circuit: Drain-
ing - Filling) (62A, Air conditioning).
aRemove:
-the engine undertray bolts,
-the engine undertray,
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection).
aDrain the cooling system (see 19A, Cooling, Cool-
ing system: Draining - Refilling, page 19A-9) . Special tooling required
Mot. 1448Remote operation pliers for
hose clips .
Equipment required
refrigerant charging station
safety strap(s)
Tightening torquesm
bolt of the dehydrator
reservoir - « expansion
valve connecting pipe » 8 N.m
compressor - con-
denser « connecting
pipe bolt » 8 N.m
air conditioning connect-
ing pipe bolts8 N.m
IMPORTANT
When working in the engine compartment, take
care as the radiator fan(s) may start up unexpect-
edly (risk of being cut).
To avoid any risk of serious burns when the engine
is hot:
-do not open the expansion bottle cap,
-do not drain the cooling system,
-do not open the bleed screw(s).
WARNING
Prepare for the flow of fluid, and protect the sur-
rounding components.
WARNING
When carr ying out a repair that requires a complete
change, it is essential to flush the circuit with clean
water, blast compressed air through the circuit to
drive out the water, fill and bleed the circuit and
then measure the effective protection.
The cr iteria to be met are:
-protection down to -25˚C ±± ± ±
2 for cold and temper-
ate countries,
-protection down to -40˚C ±± ± ±
2 for "extreme cold"
countries.

19A-22
COOLING
Cooling radiator: Removal - Refitting
K4M
19A
On the workbench
aUnclip:
-the engine cooling fan assembly from the radiator
at (8) by pushing it upwards to detach the brackets
holding it,
-the cooling radiator protector (9) .
REFITTING
I - REFITTING PREPARATION OPERATION
aAlways replace the seals on the air conditioning
pipes.
On the workbench
aClip:
-the radiator protector,
-the engine cooling fan assembly to the cooling ra-
diator.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the « radiator - condenser - fan » assembly,
-the radiator mounting cross member (see Radiator
mounting cross member: Removal - Refitting)
(41A, Front lower structure).III - FINAL OPERATION.
aClip:
-the cooling radiator top and bottom hose on the en-
gine cooling fan assembly,
-the engine cooling fan assembly wiring.
aConnect:
-the engine cooling fan assembly connector,
-the engine cooling fan assembly resistor connec-
tor.
aConnect:
-the cooling radiator top hose,
-the cooling radiator degassing hose.
aUsing the (Mot. 1448), fit:
-the cooling radiator top hose clip,
-the cooling radiator degassing hose clip.
aRefit the new seals on the air conditioning pipes.
aConnect:
-the « dehydrator reservoir - expansion valve » con-
necting pipe,
-the « compressor - condenser » connecting pipe.
aTighten to torque:
-the bolt of the dehydrator reservoir -
« expansion valve connecting pipe » (8 N.m),
-the compressor - condenser « connecting pipe
bolt » (8 N.m).
aTorque tighten the air conditioning connecting
pipe bolts (8 N.m).
aRefit the condenser protector.
aConnect the air conditioning pressure sensor con-
nector.
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
132336

19A-24
COOLING
Coolant pump: Removal - Refitting
D4F or D7F
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aDisconnect the battery (see ) (MR 411, 80A, Bat-
tery).
aRemove:
-the front right-hand wheel (see Wheel: Removal -
Refitting) (MR 411, 35A, Wheels and tyres),
-the front wheel arch liner (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the engine tie-bar (see 19D, Engine mounting,
Lower engine tie-bar: Removal - Refitting, page
19D-18) ,
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) ,
-the timing belt (see 11A, Top and front of engine,
Timing belt: Removal - Refitting, page 11A-27) .
aDrain the cooling system (see 19A, Cooling, Cool-
ing system: Draining - Refilling, page 19A-9) .
aRemove the rigid coolant pipe bolt on the multifunc-
tion support.
aMove the rigid water pump pipe aside.aRemove the coolant pump inlet pipe (see 19A,
Cooling, Coolant pump inlet pipe: Removal - Re-
fitting, page 19A-58) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the coolant pump bolts,
-the coolant pump,
-the coolant pump seal.
aRemove the coolant pump bolts.
aMove the coolant pump 5 mm away from its bearing
face.
aPivot the coolant pump casing in the direction of the
arrows, (1) and then (2) .
aRemove:
-the coolant pump, Tightening torquesm
coolant pump bolts10 N.m
AIR CONDITIONING
D4F, and 780 or 782
STANDARD HEATING
AIR CONDITIONING
120515

19A-26
COOLING
Coolant pump: Removal - Refitting
D4F or D7F
19A
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the front wheel arch liner (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front right-hand wheel (see Wheel: Removal -
Refitting) (MR 411, 35A, Wheels and tyres).
aFill and bleed the cooling system (see 19A, Cool-
ing, Cooling system: Draining - Refilling, page
19A-9) .
aConnect the battery (see ) (MR 411, 80A, Battery).

19A-27
COOLING
Coolant pump: Removal - Refitting
K9K
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove:
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment),
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the halogen headlights (see Halogen headlight:
Removal - Refitting) (80B, Headlights),
-the front upper cross member (see Front upper
cross member: Removal - Refitting) (42A, Upper
front structure),-the lower engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) ,
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the crankshaft accessories pulley (see 11A, Top
and front of engine, Crankshaft accessories
pulley: Removal - Refitting, page 11A-20) ,
-the camshaft position sensor (see 13B, Diesel in-
jection, Camshaft position sensor: Removal -
Refitting, page 13B-14) ,
-the timing belt (see 11A, Top and front of engine,
Timing belt: Removal - Refitting, page 11A-27) .
aRemove:
-the inner timing cover bolts (1) ,
-the inner timing cover.
aDrain the cooling system (see 19A, Cooling, Cool-
ing system: Draining - Refilling, page 19A-9) . Tightening torquesm
coolant pump bolts10 N.m
WARNING
The coolant helps to keep the engine running prop-
erly (heat exchange).
The system does not operate using pure water.
WARNING
Drain with the engine warm.
Flush and refill with the engine cold or warm.
Never flush a hot engine (risk of major thermal
shock).
102266