2009 RENAULT TWINGO RS dashboard

87B-2
PASSENGER COMPARTMENT CONNECTION UNIT
UCH: Removal - Refitting
87B
aUnclip the upper dashboard storage compartment
(3) .
aRemove:
-the glovebox (see Glovebox: Removal - Refit-
ting) (MR 412, 57A, Interior equipment),
-the passenger front airbag (see 88C, Air bag and
Pretensioners, Passenger's frontal airbag: Re-
moval - Refitting, page 88C-8) .aRemove the front left-hand side air distribution duct
(see Front side air distribution duct: Removal -
Refitting) (61A, Heating system).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the UCH from its mounting at (5) .
aTilt the UCH at (6) .
119502
RIGHT-HAND DRIVE
121208
LEFT-HAND DRIVE
119507

87B-3
PASSENGER COMPARTMENT CONNECTION UNIT
UCH: Removal - Refitting
87B
aExtract the UCH (7) by the location of the upper das-
hboard storage compartment.
aDisconnect the connectors (8) from the UCH.
aUnclip the UCH from its mounting at (5) .
aTilt the UCH at (6) .aExtract the UCH (7) by the location of the front pas-
senger's airbag.
aDisconnect the connectors (8) from the UCH.
aRemove the UCH.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aConnect the UCH connectors.
aRefit the UCH on its mounting.
aClip the UCH onto its mounting.
II - FINAL OPERATION.
aRefit the front left-hand side air distribution duct (see
Front side air distribution duct: Removal - Refit-
ting) (61A, Heating system).
aClip the upper dashboard storage compartment into
place.
aConnect the various connectors of the dashboard
lower trim.
aClip on the dashboard lower trim.
121207
RIGHT-HAND DRIVE
125234
125235
LEFT-HAND DRIVE

87C-1
OPENING ELEMENT MANAGEMENT
Opening elements management: List and location of components87C
I - LIST OF COMPONENTS
II - LOCATION OF COMPONENTS
1 - UCH
The UCH is located in the dashboard, above the pas-
senger compartment relay/fuse box; to remove it (see
87B, Passenger compartment connection unit,
UCH: Removal - Refitting, page 87B-1) .2 - Passenger compartment fuse and relay box
3 - Remote door locking control
To replace the battery (see 82A, Engine immobiliser,
Battery for remote door locking control: Removal -
Refitting, page 82A-8) . No. Description
(1) UCH
(2) Passenger compartment fuse and relay
box
(3) Remote door locking control
(4) Centr al door locking switch
(5) Tailgate opening switch
119507
119504
107733

87D-2
ELECTRIC WINDOWS - SUNROOF
Electric sunroof: List and location of components
OPENING ROOF
87D
I - LIST OF COMPONENTS
II - LOCATION OF COMPONENTS
1 - UCH
The UCH is located in the dashboard, above the pas-
senger compartment relay unit; to remove it (see 87B,
Passenger compartment connection unit, UCH: Re-
moval - Refitting, page 87B-1) .2 - Passenger compartment relay unit
3 - Sunroof switch No. Description
(1) UCH
(2) Passenger compartment fuse and relay
box
(3) Sunroof switch
(4) Sunroof moving panel
(5) Sunroof motor - computer
119507
119504
121391

87F-1
PARKING DISTANCE CONTROL
Parking distance control: List and location of components
REAR PROXIMITY RADAR
87F
I - LIST OF COMPONENTS
II - LOCATION OF COMPONENTS
1 - Parking distance control switch
The parking distance control switch (1) is located on
the dashboard lower trim under the steering wheel.2 - Parking distance control buzzer
The parking distance control buzzer (2) is located un-
der the left-hand rear quarter panel trim (see Quarter
panel trim: Removal - Refitting) (MR 412, 71A, Body
internal trim).
3 - Distance control radar No. Description
(1) Parking distance control switch
(2) Parking distance control buzzer
(3) Distance control radar
(4) Parking distance control computer
121372
121367
121374

87F-3
PARKING DISTANCE CONTROL
Parking distance control switch: Removal - Refitting
REAR PROXIMITY RADAR
87F
REMOVAL
I - REMOVAL PREPARATION OPERATION
aUnclip the dashboard lower trim (1)
aDisconnect the connectors.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the parking distance control switch from the
dashboard lower trim by pressing the clips (2) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aClip the parking distance control switch on the dash-
board lower trim.
II - FINAL OPERATION.
aConnect the connectors.
aClip on the dashboard lower trim.
120278
121373

88A-3
WIRING HARNESS
Front left-hand wiring: Removal - Refitting
LEFT-HAND DRIVE
88A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aSwitch off the ignition.
aRemove:
-the battery (see 80A, Battery, Battery: Removal -
Refitting, page 80A-2) ,
-the battery tray (see 80A, Battery, Battery tray:
Removal - Refitting, page 80A-6) ,
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the side indicators (see 80B, Headlights, Side in-
dicator: Removal - Refitting, page 80B-13) ,
-the master cylinder (see Master cylinder: Remo-
val - Refitting) (MR 411, 37A, Mechanical compo-
nent controls),
-the brake servo (see Brake servo: Removal - Re-
fitting) (MR 411, 37A, Mechanical component con-
trols),
-the left-hand suspended engine mounting (see
Left-hand suspended engine mounting: Remo-
val - Refitting) (MR 411, 19D, Engine mounting).aUnclip the glovebox.
aRemove the dashboard lower trim.
aDisconnect the cruise control switch connector (1) .
aRemove:
-the bolts (2) IMPORTANT
Consult the safety and cleanliness advice and ope-
ration recommendations before carrying out any
repair (see 88A, Wiring harness, Wiring: Precau-
tions for the repair, page 88A-2) .
Note:
The dashboard does not need to be removed in
order to access the pedal wiring.
119506
CRUISE CONTROL
121212

88A-7
WIRING HARNESS
Front left-hand wiring: Removal - Refitting
LEFT-HAND DRIVE
88A
-the horn connector (13) ,
-the windscreen washer pump connector (14) ,
-the front left-hand side light connector (15) ,
-the front left-hand headlight connector (16) ,
-the front left-hand indicator connector (17) ,
-the headlight beam adjustment motor connectors
(18) ,
-the front right-hand wheel speed sensor connector
(19) ,
-the hydraulic brake unit connector (20) ,
-the injection computer connector (21) ,
-the front left-hand wheel speed sensor connector
(22) ,
-the front left-hand wiring/passenger compartment
wiring connectors (23) ,
-the clutch pedal position sensor connector (24) ,
-the STOP warning light switch connector (25) ,
-the acceleration pedal potentiometer connector
(26) .
aDisconnect the regulated additional heater connec-
tor (27) .
aRemove the additional heater earth wiring nut (28) .
aDisconnect the gearbox pump assembly relay con-
nector (29) .
aRemove:
-the earth wiring nut on the front right-hand side
member (30) ,
-the earth wiring nut on the front left-hand side
member (31) ,
-the earth wiring nut on the body (32) ,
-the hydraulic brake unit earth wiring nut (33) ,
-the earth wiring nut on the negative battery terminal
(34) ,
-the earth wiring nut on the bodywork (35) ,-the front windscreen wiper mechanism (see 85A,
Wiping - Washing, Windscreen wiper mecha-
nism: Removal - Refitting, page 85A-10) .
aUnclip:
-the section of wiring from the bulkhead,
-the section of wiring on the front bumper cross
member,
-the section of wiring from the windscreen washer
reservoir
-the section of wiring from the dashboard cross
member.
aUnclip the front left-hand wiring from the bulkhead.
aRemove the front left-hand wiring through the engi-
ne compartment.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aIf replacing with a complete wiring harness, lock the
unused connectors (see Connectors: Sealing and
locking) (Technical Note 6015A, 88A, Wiring).
II - REFITTING OPERATION FOR PART
CONCERNED
aPosition the front left-hand wiring across the bulk-
head.
aClip the front left-hand wiring onto the bulkhead.
aConnect:
-the acceleration pedal potentiometer connector,
-the STOP warning light switch connector,
-the clutch pedal position sensor connector ,
-the front left-hand wiring/passenger compartment
wiring connectors,
-the injection computer connector,
-the front left-hand wheel speed sensor connector,
-the hydraulic brake unit connector,
-the front right-hand wheel speed sensor connector,
-the headlight beam adjustment motor connectors, CLIMATE CONTROL
JH1
WARNING
To prevent any damage during the removal ope-
ration, check that the wiring is free from its moun-
tings (retaining clip, plastic clip, adhesive tape,
connector, etc.).