2009 RENAULT TWINGO RS air condition

86A-68
AFTER REPAIRRepeat the conformity check from the start.
V1 MR-413-X44-86A150$160.mif
86A
R2-08
Vdiag No.: 64
PR007FM1 RADIO FIELD INTENSITY
NOTESThe values shown in this conformity check are given as a guide.
Test conditions: Engine off, ignition on and radio on.
Perform the conformity check outside, in an area with good radio reception and
without obstacles.
Conformity check:
Monitor the PR007 value of the diagnostic tool data display.
Display of frequency received for the radio station currently set.
Radio field intensity parameterRadio reception level
(data display)
Outdoor testUnit: dBµV
Data interpretation:
Radio reception value Status
X > 18 dBµVCorrect radio reception
14 dBµV < X < 18 dBµVCorrect sound quality
RDS decoding (for example: display
of station names) correct
Automatic synchronisation / Presence
in the radio list
not satisfactory
10 dBµV < X < 14 dBµVCorrect sound quality
RDS decoding (for example: display
of station names) not satisfactory
Automatic synchronisation / Presence
in the radio list
not satisfactory
X > 10 dBµVRadio reception not satisfactory
If the fault is still present, contact the Techline.
R208_V64_PR007
RADIO
Fault finding – Interpretation of parameters

86A-71
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-413-X44-86A150$190.mif
86A
R02-08
Vdiag No.: 64
ALP 1 No dialogue with the computer
NOTESTry to establish dialogue with a computer on another vehicle to check that the
diagnostic tool is not faulty. If the diagnostic tool is not causing the fault and dialogue
cannot be established with any other computer on the same vehicle, it may be that
a faulty computer is disrupting the fault finding line.
Use a process of successive disconnections to locate this computer.
Check the battery voltage, component code 107, and perform the necessary operations
to obtain the correct voltage (12 V < X < 15 V).
Ensure that the communication conditions are met: + After ignition feed activated
and radio On/Off button pressed.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
For a vehicle equipped with a Navigation computer, use component 1714, Multimedia
connection unit, for fault finding on the Multimedia interface unit.
Otherwise use component 653, display computer.
Is the multimedia interface unit recognised
during the multiplex network test?The multimedia interface unit activates other
multimedia system computers.
Consult ALP 1 for the multimedia interface unit
(see 86D, Multimedia interface unit, Fault
finding chart).
Reconfigure the multimedia interface unit
(see 86D, Multimedia interface unit,
Configurations and Programming).
NO
YES
A
R208_V64_ALP1
RADIO
Fault finding – Fault Finding Chart

86A-74
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-413-X44-86A150$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: 64
ALP 1
CONTINUED 3
Check the condition and connection of the radio
computer connector, component code 261.
If the connector is faulty and there is a repair
method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace
the wiring.
Disconnect the radio computer connector,
component code 261.
Check for + 12 V and earth on the radio between
the following connections:
•BCP4 of component 261 and the MAO
(New Twingo) or MT (Clio III) earth.
Are the checks correct?
Check for + 12 V on the radio computer between
the following connections:
•BCP4 of component 261 and earth.Check the continuity, insulation and
absence of interference resistance of
connection MAO (New Twingo) or MT
(Clio III) between the radio computer,
component code 261 and the earth.
If the connection is faulty and there is a repair
procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring,
otherwise replace it. Is the result of the check correct?
B
NO
YESD
NO
YES
NO
E

86A-83
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V1 MR-413-X44-86A150$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: 64
ALP 3 The radio does not operate when the ON button is pressed
NOTESNone.
Press the ON button of the radio.
Switch on the lights
Does the radio backlighting operate?See ALP1 No dialogue with the computer.
Is the volume 0 or on pause?Increase the volume or restart play.
Is the front/rear balance set completely to
the rear speakers?Set the front/rear balance to 0.
Are the condition and connections of the
speaker connector and speaker connections
in order?Reconnect or repair the connector(s), otherwise
replace the wiring. (see Technical Note 6015A,
Repairing electrical wiring, Wiring:
Precautions for repair).
See ALP 10 Sound fault for a speaker or
tweeter.
NO
YES
YES
NO
YES
NO
NO
YES
R208_V64_ALP3

86A-85
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V1 MR-413-X44-86A150$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: 64
ALP 5 The radio control satellite does not operate or operates poorly
NOTESUse the Wiring Diagrams Technical Note for Clio III or New Twingo.
Has dialogue been established with the
multimedia interface unit (Display or
multimedia connection unit)?Consult ALP 1 No dialogue with the
computer for the multimedia interface unit
(see 86D, Multimedia interface unit, Fault
finding charts).
Check the condition of the radio control satellite
(see 86D, Multimedia interface unit,
Conformity check).
Are the satellite statuses correct?Contact the Techline.
NO
YES
YES
NO
A
R208_V64_ALP5

86A-86
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V1 MR-413-X44-86A150$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: 64
ALP 5
CONTINUED 1
Check the condition and connection of the
satellite control connector, component code 325
(New Twingo) or 1519 (Clio III).
If the connector is faulty and there is a repair
method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace
the wiring.
Check the continuity, insulation and absence of
interference resistance on the following
connections:
•34AT, between components 653 or 1714
and 325 (New Twingo) or 1519 (Clio III),
•34AR, between components 653 or 1714
and 325 (New Twingo) or 1519 (Clio III),
•34AS, between components 653 or 1714
and 325 (New Twingo) or 1519 (Clio III),
•34AQ, between components 653 or 1714
and 325 (New Twingo) or 1519 (Clio III),
•34AU, between components 653 or 1714
and 325 (New Twingo) or 1519 (Clio III),
•34AP between components 653 or 1714
and 325 (New Twingo) or 1519 (Clio III),
•34AO between components 653 or 1714
and 1519 (Clio III only).If the connection or connections are faulty and
there is a repair procedure (see Technical
Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the
wiring, otherwise replace it.
Are the checks correct?
If the fault is still present, contact Techline.
A
NO
NO
YES
B

86A-88
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V1 MR-413-X44-86A150$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: 64
ALP 6 Radio reception fault.
NOTESSee Clio III or New Twingo wiring diagrams.
For the aerial, use component code 1874 for a vehicle equipped with a navigation
system, and 1208 for a vehicle without this option.
Check the presence and condition of the radio
aerial.Replace the radio aerial, component code
1208 or 1874 (see MR 392, 86A, Radio, Radio
aerial: Removal - Refitting) for New Twingo
or (see MR 411, 86A, Radio, Radio aerial:
Removal - Refitting) for Clio III. Is the radio aerial correct?
Check the condition of the connections of the
radio aerial coaxial cable at the radio aerial,
component code 1208 or 1874 and of the radio,
component code 261.
Are the connections correct?If the connectors are faulty and if there is a
repair procedure (see Technical Note 6015A,
Repairing electrical wiring, Wiring:
Precautions for repair) repair the
connector(s); otherwise, replace the wiring.
NO
YES
NO
YES
A
R208_V64_ALP6

86A-94
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V1 MR-413-X44-86A150$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: 64
ALP 10 Sound fault for a speaker or tweeter (regardless of source).
NOTESUse the Wiring Diagrams Technical Note for Clio III or New Twingo.
Run a command for each speaker using AC004 Front
right-hand speaker line test, AC005 Front left-hand
speaker line test, AC006 Rear right-hand speaker line
test, AC007 Rear left-hand speaker line test.
Did the tests successfully identify which speaker(s)
is the source of the problem? Repeat the procedure, and if the fault
still does not appear, contact the
Techline.
Check the speaker or tweeter which is the source of the
problem (visual appearance and mechanical: presence
of foreign bodies, mounting and condition of the
membrane).If possible, repair the incorrect
component(s), otherwise replace the
faulty speaker(s), component codes
1597, 1598, 189 and 190 (see MR 392
(Clio III) or MR 411 (New Twingo),
86A, Radio, Front speakers:
Removal - Refitting or (see MR 392
(Clio III) or MR 411 (New Twingo),
86A, Radio, Rear speakers:
Removal - Refitting) and/or the faulty
tweeter(s), component codes 365, 366
(see MR 392 (Clio III) or MR 411
(New Twingo), 86A, Radio, Tweeter:
Removal - Refitting). Are the checks correct?
NO
YES
NO
YES
A
R208_V64_ALP10