2009 RENAULT TWINGO RS wiring

86A-55
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86A150$120.mif
RADIO
Fault finding – Interpretation of faults86A
R2-08
Vdiag No.: 64
DF054
PRESENT
OR
STOREDREAR LEFT-HAND TWEETER
CO: Open circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–The multimedia system was switched on using the on/off button for at least
10 seconds,
–Command AC007 Rear left-hand speaker line test was run,
–The fault can only be detected if the battery voltage is between:
12 V < X < 15 V.
Note:
The rear tweeters are integrated into the rear speakers and are only available on
New Twingo.
Use the Wiring Diagrams Technical Note for New Twingo.
Check the condition and connection of the connectors of radio 261 and of the rear left-hand speaker 190 (bent or
broken tabs, etc.).
If any of the connectors are faulty and there is a repair method (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Disconnect the connector of component 190 (see MR 411 (New Twingo) Mechanical, 86A, Radio, Rear speaker:
Removal - Refitting).
Measure the resistance of component 190 using a multimeter, with the ignition off.
If the resistance is not between: 3.5 Ω < X < 4.5 Ω, replace component 190 (see MR 411 (New Twingo)
Mechanical, 86A, Radio, Rear speaker: Removal - Refitting).
Check the continuity, insulation and absence of interference resistance on the following connections:
•34A between components 261 and 190,
•34B between components 261 and 190.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault persists, contact your Techline.
R208_V64_DF054

86A-58
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86A150$120.mif
RADIO
Fault finding – Interpretation of faults86A
R2-08
Vdiag No.: 64
DF056
PRESENT
OR
STOREDMICROPHONE
CC.0: Short circuit to earth
CO: Open circuit
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
–the + after ignition feed is activated,
–the multimedia system has been switched on using the on/off button,
–the "hands-free" function has been activated,
–the command AC010 Microphone test was run.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Look for any damage to the wiring harness and check the condition and connection of the connectors for
components 261 and 789.
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Run command AC010 Microphone Test and check that the microphone, component code 789 is correctly
supplied between connections 107G and 107J.
Check the continuity, insulation and absence of interference resistance on the following connections:
•107F between components 261 and 789,
•107G between components 261 and 789,
•107J between components 261 and 789,
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the microphone (see MR 392 (Clio III) or MR 411 (New Twingo) Mechanical,
86B, Car phone, "Hands-free" microphone: Removal - Refitting).
R208_V64_DF056

86A-59
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory, after pressing the ON/
OFF button.
Deal with any other faults.
V1 MR-413-X44-86A150$120.mif
RADIO
Fault finding – Interpretation of faults86A
R2-08
Vdiag No.: 64
DF064
PRESENT
OR
STOREDACTIVATION SIGNAL
CC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–the + after ignition feed is activated,
–the multimedia system has been switched on using the on/off button.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
For a vehicle equipped with a navigation system, use the multimedia connection unit
computer, component code 1714, for fault finding.
For a vehicle without a navigation system, use the display computer, component code
653, for fault finding.
Check the condition of the connector on the radio, component code 261, and, depending on the equipment level,
on the display, component code 653, or on the multimedia connection unit, component code 1714.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connections:
•34HY between,components 261 and 653 or 1714,
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connection is correct, replace the radio (see MR 392 (Clio III) or MR 411 (New Twingo) Mechanical, 86A,
Radio, Radio: Removal - Refitting).
If the fault persists, contact your Techline.
R208_V64_DF064

86A-71
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-413-X44-86A150$190.mif
86A
R02-08
Vdiag No.: 64
ALP 1 No dialogue with the computer
NOTESTry to establish dialogue with a computer on another vehicle to check that the
diagnostic tool is not faulty. If the diagnostic tool is not causing the fault and dialogue
cannot be established with any other computer on the same vehicle, it may be that
a faulty computer is disrupting the fault finding line.
Use a process of successive disconnections to locate this computer.
Check the battery voltage, component code 107, and perform the necessary operations
to obtain the correct voltage (12 V < X < 15 V).
Ensure that the communication conditions are met: + After ignition feed activated
and radio On/Off button pressed.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
For a vehicle equipped with a Navigation computer, use component 1714, Multimedia
connection unit, for fault finding on the Multimedia interface unit.
Otherwise use component 653, display computer.
Is the multimedia interface unit recognised
during the multiplex network test?The multimedia interface unit activates other
multimedia system computers.
Consult ALP 1 for the multimedia interface unit
(see 86D, Multimedia interface unit, Fault
finding chart).
Reconfigure the multimedia interface unit
(see 86D, Multimedia interface unit,
Configurations and Programming).
NO
YES
A
R208_V64_ALP1
RADIO
Fault finding – Fault Finding Chart

86A-73
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-413-X44-86A150$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: 64
ALP 1
CONTINUED 2
Check the continuity, insulation and absence
of interference resistance on the following
connection:
•34HU between components 261 and 1714.
If the connection is faulty and there is a
repair procedure (see Technical Note
6015A, Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring,
otherwise replace it. Are the checks correct?
Check the insulation, continuity and absence of
interference resistance on the following
connections:
•34GC between components 662 and 261,
•34GB between components 662 and 261.If the connection or connections are faulty
and there is a repair procedure (see
Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it. Are the checks correct?
Check the insulation, continuity and absence of
interference resistance on the following
connections:
•34GC and 107X between components 261 and
1714,
•34GB and 107W between components 261 and
1714.Replace the navigation computer,
component code 662 (see MR 392,
Mechanical, 83C, On-board telematics
system, Navigation computer:
Removal – Refitting). Are the checks correct?
Replace the radio, component code 261 (see MR
392, Mechanical, 86A, Radio, Radio: Removal -
Refitting).
C
YES
NO
YES
NO
YES
NO
YES

86A-74
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-413-X44-86A150$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: 64
ALP 1
CONTINUED 3
Check the condition and connection of the radio
computer connector, component code 261.
If the connector is faulty and there is a repair
method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace
the wiring.
Disconnect the radio computer connector,
component code 261.
Check for + 12 V and earth on the radio between
the following connections:
•BCP4 of component 261 and the MAO
(New Twingo) or MT (Clio III) earth.
Are the checks correct?
Check for + 12 V on the radio computer between
the following connections:
•BCP4 of component 261 and earth.Check the continuity, insulation and
absence of interference resistance of
connection MAO (New Twingo) or MT
(Clio III) between the radio computer,
component code 261 and the earth.
If the connection is faulty and there is a repair
procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring,
otherwise replace it. Is the result of the check correct?
B
NO
YESD
NO
YES
NO
E

86A-75
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-413-X44-86A150$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: 64
ALP 1
CONTINUED 4
Check the continuity, insulation and absence of
interference resistance on the following
connections:
•BCP4 between components 261 and 710,
•BP69 between components 260 and 710
(only for Clio III).
If the connection or connections are faulty and
there is a repair procedure (see Technical Note
6015A, Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring,
otherwise replace it.
E
NO

86A-77
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-413-X44-86A150$190.mif
RADIO
Fault finding – Fault Finding Chart86A
R01-08
Vdiag No.: 64
ALP 1
CONTINUED 6
Check the continuity, insulation and absence
of interference resistance on the following
connection:
•34HY between components 261 and 653 or
1714.If the connection is faulty and there is a repair
procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring,
otherwise replace it. Is the result of the check correct?
Replace the display, component code 653
(see MR 392 (Clio III) or MR 411 (New Twingo)
Mechanical, 86A, Radio, Display: Removal –
Refitting) or the multimedia connection unit,
component code 1714 or (see MR 392 (Clio III)
Mechanical, 83C, On-board telematics system,
Multimedia network interface
unit: Removal – Refitting).
G
YES
NO
YES