2009 RENAULT TWINGO RS coolant

17B-220V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET289INSTRUMENT PANEL INJECTION CONNECTION
STATUS
DEFINITIONCONNECTED: This status indicates that the connection between the injection
computer and the instrument panel is not defective.
DISCONNECTED: This status indicates that the connection between the injection
computer and the instrument panel is defective.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
NOT CONNECTEDThe connection between the injection computer and the instrument panel is defective,
test the instrument panel (see 83A, Instrument panel) and the multiplex network
(see 88B, Multiplexing).
SIM32_V44_ET289/SIM32_V4C_ET289/SIM32_V50_ET289/SIM32_V54_ET289
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-221V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET290FUEL PUMP RELAY CONTROL
STATUS
DEFINITIONACTIVE: This status indicates that the fuel pump relay control is active.
INACTIVE: This status indicates that the fuel pump relay control is deactivated.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
There must be no present or stored faults.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
"ACTIVE"
or
"INACTIVE"This status becomes active when the engine is started.
In the event of a fault, apply the interpretation of DF085 Fuel pump relay control
circuit
SIM32_V44_ET290/SIM32_V4C_ET290/SIM32_V50_ET290/SIM32_V54_ET290
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-222V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET300RICHNESS REGULATION
STATUS
DEFINITIONACTIVE: This indicates that the richness is regulated.
INACTIVE: This status indicates that the richness is not regulated.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check with engine stopped and ignition on.
"ACTIVE"The status is ACTIVE when the engine is running.
"INACTIVE"The status is INACTIVE when the engine is not running.
Conformity check with the engine running and engine coolant temperature > 80˚C
SIM32_V44_ET300/SIM32_V4C_ET300/SIM32_V50_ET300/SIM32_V54_ET300
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-223V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET340AUTOMATIC TRANSMISSION REQUEST TO ACTIVATE OBD

WARNING LIGHT
STATUS
DEFINITIONACTIVE: This status indicates that the automatic transmission computer request to
activate the OBD warning light is active.
INACTIVE: This status indicates that the automatic transmission computer request to
activate the OBD warning light is inactive.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
"ACTIVE"
or
"INACTIVE"For normal engine operation, the status must be INACTIVE.
If activation of the OBD warning light on the instrument panel is not consistent with
the status,
test the instrument panel (see 83A, Instrument panel).
SIM32_V44_ET340/SIM32_V4C_ET340/SIM32_V50_ET340/SIM32_V54_ET340
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-224V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET341IMMOBILISER CODE PROGRAMMED
STATUS
DEFINITIONYES: This status indicates that the immobiliser code has been programmed.
NO: This status indicates that the immobiliser code has not been programmed.
NOTESSpecial notes:
Perform these checks if the parameters correspond with the system operation
programming.
There must be no present or stored faults.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
"YES"Status ET341 is YES if dialogue is possible between the UCH computer and the
injection computer and the key code is recognised.
The engine is only authorised to start if the code is recognised by the UCH computer
and if status ET003 Immobiliser is INACTIVE.
In the event of a fault, (see 87B, Passenger compartment connection unit,
conformity check).
"NO"Status ET341 is NO if dialogue is not possible between the UCH computer and the
injection computer (status ET003 remains ACTIVE).
This fault may be caused by incorrect key programming or a lack of key programming.
In this case, refer to the UCH fault finding note (see 87B, Passenger compartment
connection unit) and follow the key programming procedure.
If the key programming is not the cause, run a multiplex network test (see 88B,
Multiplexing) and check that dialogue between the UCH and the injection
computer is possible.
If dialogue is not established, contact the Techline.
SIM32_V44_ET341/SIM32_V4C_ET341/SIM32_V50_ET341/SIM32_V54_ET341
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-225V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET351INJECTION ELECTRONIC STABILITY PROGRAM CONNECTION
STATUS
DEFINITIONCONNECTED: This status indicates that the connection between the injection
computer and the ESP is not defective.
DISCONNECTED: This status indicates that the connection between the injection
computer and the ESP is defective.
NOTESSpecial notes:
Perform these checks if the parameters correspond with the system operation
programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
NOT CONNECTEDThe connection between the injection computer and the ESP is defective, test the
ABS/ESP computer (see 38C, Anti-lock braking system) and the multiplex network
(see 88B, Multiplexing).
SIM32_V44_ET351/SIM32_V4C_ET351/SIM32_V50_ET351/SIM32_V54_ET351
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-226V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET405CLUTCH PEDAL SWITCH
STATUS
DEFINITIONACTIVE: this status indicates that the clutch pedal is depressed.
INACTIVE: this status indicates that the clutch pedal is released.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Use the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III
or MODUS.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
"ACTIVE"Clutch pedal depressed.
Non-conformity of the brake signals and or the clutch switch signals can cause the
engine to race during gear changes.
"INACTIVE"Clutch pedal released.
Non-conformity of the brake signals and or the clutch switch signals can cause the
engine to race during gear changes.
SIM32_V44_ET405/SIM32_V4C_ET405/SIM32_V50_ET405/SIM32_V54_ET405
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-228V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET415CRUISE CONTROL/SPEED LIMITER DEACTIVATION
STATUS
DEFINITIONThis status varies according to engine specifications.
NOTESSpecial notes:
Perform these checks if the parameters correspond with the system operation
programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
STATUS 1:Traction control request.
STATUS 2:Brake pedal depressed.
STATUS 3:Clutch pedal depressed.
STATUS 4:Suspend button pressed.
STATUS 5:Cruise control or speed limiter monitoring.
STATUS 6:Inconsistency between the request and the vehicle speed. Gear lever in neutral
(manual gearbox) or the N position (automatic gearbox).
SIM32_V44_ET415/SIM32_V4C_ET415/SIM32_V50_ET415/SIM32_V54_ET415
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.