2009 RENAULT TWINGO RS stop start

17B-200V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET062FLYWHEEL SIGNAL–detected
–not detected
STATUS
DEFINITIONDETECTED: This status indicates that the engine flywheel signal is detected.
NOT DETECTED: This status indicates that the engine flywheel signal is not detected.
NOTESThere must be no present or stored faults.
Special notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: engine stopped and ignition on.
NOT DETECTEDThe engine flywheel signal is detected after the engine is started.
In the event of a fault apply the interpretation for DF154 Flywheel signal sensor
circuit.
Conformity check with engine running at idle speed, engine coolant temperature > 80˚C
DETECTED The engine flywheel signal is detected after the engine is started.
In the event of a fault apply the interpretation for DF154 Flywheel signal sensor
circuit.
SIM32_V44_ET062/SIM32_V4C_ET062/SIM32_V50_ET062/SIM32_V54_ET062
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-202V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET076STARTING
STATUS
DEFINITIONPROHIBITED: This status indicates that starting is not possible.
AUTHORISED: This status indicates that starting is possible.
NOTESSpecial note:
Only perform the tests if the statuses do not correspond with the system programming
functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
"PROHIBITED"Refer to the UCH fault finding note, (see 87B, Passenger compartment connection
unit) or to the Protection and Switching Unit fault finding note, (see 87G, Engine
compartment connection unit).
"AUTHORISED"Refer to the UCH fault finding note, (see 87B, Passenger compartment connection
unit) or to the Protection and Switching Unit fault finding note, (see 87G, Engine
compartment connection unit).
SIM32_V44_ET076/SIM32_V4C_ET076/SIM32_V50_ET076/SIM32_V54_ET076
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-208V7 MR-413-X44-17B000$152.mif
17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET088REQUEST TO START COMPRESSOR
STATUS
DEFINITIONACTIVE: This status indicates that the compressor is engaged.
INACTIVE: This status indicates that the compressor is not engaged.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Engine running, engine coolant temperature > 80˚C
"ACTIVE"The air conditioning request has been made by the driver when pressing one of the
air conditioning controls (Auto or AC).
Status ET088 becomes ACTIVE and the computer authorises or does not authorise
air conditioning depending on the operating conditions.
If status ET088 does not become ACTIVE when the control button is pressed, refer
to the air conditioning fault finding note (see 62A, Heating system, 62B, Climate
control or 62C, Manual air conditioning).
Note: Compressor operation is only authorised when the engine is running.
Conformity check with engine stopped and ignition on.
"INACTIVE"When the driver deactivates the air conditioning, status ET088 must become
INACTIVE.
If it does not, refer to the air conditioning fault finding note (see 62A, Heating system,
62B, Climate control or 62C, Manual air conditioning).
Note: Compressor operation is only authorised when the engine is running.
SIM32_V44_ET088/SIM32_V4C_ET088/SIM32_V50_ET088/SIM32_V54_ET088
PETROL INJECTION
Fault finding – Interpretation of statuses
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-221V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET290FUEL PUMP RELAY CONTROL
STATUS
DEFINITIONACTIVE: This status indicates that the fuel pump relay control is active.
INACTIVE: This status indicates that the fuel pump relay control is deactivated.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
There must be no present or stored faults.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
"ACTIVE"
or
"INACTIVE"This status becomes active when the engine is started.
In the event of a fault, apply the interpretation of DF085 Fuel pump relay control
circuit
SIM32_V44_ET290/SIM32_V4C_ET290/SIM32_V50_ET290/SIM32_V54_ET290
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-224V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET341IMMOBILISER CODE PROGRAMMED
STATUS
DEFINITIONYES: This status indicates that the immobiliser code has been programmed.
NO: This status indicates that the immobiliser code has not been programmed.
NOTESSpecial notes:
Perform these checks if the parameters correspond with the system operation
programming.
There must be no present or stored faults.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
"YES"Status ET341 is YES if dialogue is possible between the UCH computer and the
injection computer and the key code is recognised.
The engine is only authorised to start if the code is recognised by the UCH computer
and if status ET003 Immobiliser is INACTIVE.
In the event of a fault, (see 87B, Passenger compartment connection unit,
conformity check).
"NO"Status ET341 is NO if dialogue is not possible between the UCH computer and the
injection computer (status ET003 remains ACTIVE).
This fault may be caused by incorrect key programming or a lack of key programming.
In this case, refer to the UCH fault finding note (see 87B, Passenger compartment
connection unit) and follow the key programming procedure.
If the key programming is not the cause, run a multiplex network test (see 88B,
Multiplexing) and check that dialogue between the UCH and the injection
computer is possible.
If dialogue is not established, contact the Techline.
SIM32_V44_ET341/SIM32_V4C_ET341/SIM32_V50_ET341/SIM32_V54_ET341
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-240V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET561Operating mode
STATUS
DEFINITIONALCOHOL: This status indicates that the engine runs on ETHANOL (E85).
PETROL: This status indicates that the engine runs on petrol.
NOTESThere must be no present or stored faults.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
ALCOHOL
or
PETROLThe status ET561 is ALCOHOL if the vehicle runs on ETHANOL (E85).
The status ET561 is PETROL if the vehicle runs on petrol.
–Reprogram the alcohol level (see Configurations and programming, Alcohol
level programming):
–start the engine,
–allow the engine coolant temperature to reach 75˚C, check using parameter PR064
Coolant temperature,
–run the engine at 1500 rpm for at least 5 mins,
–check that the programming has been carried out using status ET671 Alcohol
level programming and parameter PR743 Estimated alcohol level in tank,
the programming is saved when the ignition is switched off.
If the fault is still present, contact the Techline.
SIM32_V44_ET561/SIM32_V4C_ET561/SIM32_V50_ET561/SIM32_V54_ET561
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-250V7 MR-413-X44-17B000$153.mif
17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET671PROGRAMMING THE ALCOHOL LEVEL
STATUS
DEFINITIONCOMPLETED: This status indicates that the alcohol level has been programmed.
NOT COMPLETED: This status indicates that the alcohol level has not been
programmed.
NOTESSpecial notes:
Perform these checks if the statuses correspond with the system operation
programming.
There must be no present or stored faults.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
COMPLETEDStatus ET671 must be COMPLETED if the vehicle runs on alcohol.
NOT
COMPLETEDReprogram the alcohol level (see Configurations and programming, Alcohol level
programming):
–start the engine,
–allow the engine coolant temperature to reach 75˚C, check using parameter PR064
Coolant temperature,
–run the engine at 1500 rpm for at least 5 mins,
–check that the programming has been carried out using status ET671 and
parameter PR743 Estimated alcohol level in tank,
the programming is saved when the ignition is switched off.
If the fault is still present, contact the Techline.
SIM32_V44_ET671 / SIM32_V4C_ET671 / SIM32_V50_ET671 / SIM32_V54_ET671
PETROL INJECTION
Fault finding – Interpretation of statuses
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-323V7 MR-413-X44-17B000$172.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
SIM 32 injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
For CLIO III or MODUS only
PR743ALCOHOL LEVEL ESTIMATED IN THE TANK
PARAMETER
DEFINITIONThis parameter is used to estimate the percentage of alcohol contained in the petrol in
the main tank.
NOTESThere must be no present or stored faults.
Refer to CLIO III or MODUS Wiring Diagram Technical Note.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature
> 80˚C.
This percentage must be between:
0 < PR743 < 100%
This parameter allows the computer to estimate the alcohol level contained in the petrol.
Status ET671 Alcohol level programming should be COMPLETED. This indicates that the percentage of alcohol
in the tank has been detected.
If status ET671 Alcohol level programming is NOT COMPLETED, repeat the programming procedure (see
Configurations and programming, Alcohol level programming).
Disconnect the battery and the injection computer.
Check the cleanliness and condition of the connections
Using the universal bornier, check the insulation and continuity on the following connections:
●3GH between components 887 and 120.
●3GK between components 887 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the upstream oxygen sensor.
If the fault is still present, contact the Techline.
SIM32_V44_PR743 / SIM32_V4C_PR743 / SIM32_V50_PR743 / SIM32_V54_PR743
AFTER REPAIRRepeat the conformity check from the start.